[PATCH] ARM: realview: DT support for the PBA8 and PBX-A9

[robin.murphy@arm.com (Robin Murphy)]

On 24/02/16 15:54, Linus Walleij wrote:
> This adds a devicetree for the ARM RealView PBA8 platform,
> also known as HBI-0178, "RealView Platform Baseboard for
> Cortex-A8" and PBX-A9 "RealView Platform Baseboard
> Explore for Cortex-A9"
>
> Tested in QEMU with -M realview-pb-a8, as well as with
> -M realview-pbx-a9 -smp cpus=2
>
> Cc: Arnd Bergmann <arnd@arndb.de>
> Cc: Pawel Moll <pawel.moll@arm.com>
> Cc: Peter Maydell <peter.maydell@linaro.org>
> Cc: Marc Zyngier <marc.zyngier@arm.com>
> Cc: Robin Murphy <robin.murphy@arm.com>

After staying up late reading the SD card spec, I realise my diagnosis 
of the 'unsupported voltage' problem was off the mark - it's not a 
hardware compatibility issue, it's that realview_defconfig doesn't have 
CONFIG_REGULATOR_FIXED_VOLTAGE=y, so the mmc core simply didn't know of 
any available voltages at all.

For both realview_defconfig (from your realview-defconfig-redux tag with 
regulators added) and multi_v7_defconfig (with REALVIEW_DT added), the 
PB-A8 boots without complaint to a busybox nfsroot using this DT plus 
the sp810 patch. As with the Versatile AB I scored from a junk pile, 
trying to boot a full userspace from SD card makes slow progress through 
a storm of data transfer errors and eventually dies. USB is similarly 
flaky, with occasional device resets and command errors, but I don't see 
that it's this patch's fault - I think this might even be a 
pre-production board, and with the boardfile instead of DT the USB 
behaves the same while MMC and networking don't even show up - so you 
can call this a (Lightly-)Tested-By if you like.

Robin.

> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ChangeLog v1->v2:
> - Realized that the PBA8 and the PBX-A9 is very similar so
>    merged these machines into one patch sharing a common PBX
>    .dtsi file and enabled PBX-A9 as well.
> - Fixed the assignment of the SD/MMC card detect to route
>    to gpio instance 2.
> - Drop QEMU sob story from commit message.
> ---
>   arch/arm/boot/dts/Makefile                |   4 +-
>   arch/arm/boot/dts/arm-realview-pba8.dts   | 178 ++++++++++
>   arch/arm/boot/dts/arm-realview-pbx-a9.dts | 229 +++++++++++++
>   arch/arm/boot/dts/arm-realview-pbx.dtsi   | 542 ++++++++++++++++++++++++++++++
>   4 files changed, 952 insertions(+), 1 deletion(-)
>   create mode 100644 arch/arm/boot/dts/arm-realview-pba8.dts
>   create mode 100644 arch/arm/boot/dts/arm-realview-pbx-a9.dts
>   create mode 100644 arch/arm/boot/dts/arm-realview-pbx.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 39deb1741465..74261429e679 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -537,7 +537,9 @@ dtb-$(CONFIG_ARCH_REALVIEW) += \
>   	arm-realview-eb.dtb \
>   	arm-realview-eb-11mp.dtb \
>   	arm-realview-eb-11mp-revb.dtb \
> -	arm-realview-eb-a9mp.dtb
> +	arm-realview-eb-a9mp.dtb \
> +	arm-realview-pba8.dtb \
> +	arm-realview-pbx-a9.dtb
>   dtb-$(CONFIG_ARCH_ROCKCHIP) += \
>   	rk3036-evb.dtb \
>   	rk3036-kylin.dtb \
> diff --git a/arch/arm/boot/dts/arm-realview-pba8.dts b/arch/arm/boot/dts/arm-realview-pba8.dts
> new file mode 100644
> index 000000000000..d3238c252b59
> --- /dev/null
> +++ b/arch/arm/boot/dts/arm-realview-pba8.dts
> @@ -0,0 +1,178 @@
> +/*
> + * Copyright 2016 Linaro Ltd
> + *
> + * Permission is hereby granted, free of charge, to any person obtaining a copy
> + * of this software and associated documentation files (the "Software"), to deal
> + * in the Software without restriction, including without limitation the rights
> + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
> + * copies of the Software, and to permit persons to whom the Software is
> + * furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice shall be included in
> + * all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
> + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
> + * THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "arm-realview-pbx.dtsi"
> +
> +/ {
> +	model = "ARM RealView Platform Baseboard for Cortex-A8";
> +	compatible = "arm,realview-pba8";
> +	arm,hbi = <0x178>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "arm,realview-smp";
> +
> +		cpu0: cpu at 0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a8";
> +			reg = <0>;
> +		};
> +	};
> +
> +	pmu: pmu at 0 {
> +		compatible = "arm,cortex-a8-pmu";
> +		interrupt-parent = <&intc>;
> +		interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&cpu0>;
> +	};
> +
> +	/* Primary GIC PL390 interrupt controller in the test chip */
> +	intc: interrupt-controller at 1e000000 {
> +		compatible = "arm,pl390";
> +		#interrupt-cells = <3>;
> +		#address-cells = <1>;
> +		interrupt-controller;
> +		reg = <0x1e001000 0x1000>,
> +		      <0x1e000000 0x100>;
> +	};
> +};
> +
> +&ethernet {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&usb {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&soc {
> +	compatible = "arm,realview-pba8-soc", "simple-bus";
> +};
> +
> +&syscon {
> +	compatible = "arm,realview-pba8-syscon", "syscon", "simple-mfd";
> +};
> +
> +&serial0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial2 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial3 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&ssp {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&wdog0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&wdog1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer01 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer23 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio2 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&rtc {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer45 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer67 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&aaci {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&mmc {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>,
> +		     <0 18 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&kmi0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&kmi1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&clcd {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
> +};
> diff --git a/arch/arm/boot/dts/arm-realview-pbx-a9.dts b/arch/arm/boot/dts/arm-realview-pbx-a9.dts
> new file mode 100644
> index 000000000000..db808f92dd79
> --- /dev/null
> +++ b/arch/arm/boot/dts/arm-realview-pbx-a9.dts
> @@ -0,0 +1,229 @@
> +/*
> + * Copyright 2016 Linaro Ltd
> + *
> + * Permission is hereby granted, free of charge, to any person obtaining a copy
> + * of this software and associated documentation files (the "Software"), to deal
> + * in the Software without restriction, including without limitation the rights
> + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
> + * copies of the Software, and to permit persons to whom the Software is
> + * furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice shall be included in
> + * all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
> + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
> + * THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "arm-realview-pbx.dtsi"
> +
> +/ {
> +	/*
> +	 * This is the RealView Platform Baseboard Explore for Cortex-A9
> +	 * (HBI0182 + HBI0183) as described in ARM DUI 0440B
> +	 */
> +	model = "ARM RealView Platform Baseboard Explore for Cortex-A9";
> +	arm,hbi = <0x182>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "arm,realview-smp";
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&CPU0>;
> +				};
> +				core1 {
> +					cpu = <&CPU1>;
> +				};
> +			};
> +		};
> +		CPU0: cpu at 0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0x0>;
> +			next-level-cache = <&L2>;
> +		};
> +		CPU1: cpu at 1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a9";
> +			reg = <0x1>;
> +			next-level-cache = <&L2>;
> +		};
> +	};
> +
> +	L2: l2-cache {
> +		compatible = "arm,pl310-cache";
> +		reg = <0x1f002000 0x1000>;
> +		cache-unified;
> +		cache-level = <2>;
> +		/*
> +		 * Override default cache size, sets and
> +		 * associativity as these may be erroneously set
> +		 * up by boot loader(s).
> +		 */
> +		cache-size = <1048576>; // 1MB
> +		cache-sets = <4096>;
> +		cache-line-size = <32>;
> +		arm,parity-disable;
> +		arm,tag-latency = <1>;
> +		arm,data-latency = <1 1>;
> +		arm,dirty-latency = <1>;
> +	};
> +
> +	scu: scu at 1f000000 {
> +		compatible = "arm,cortex-a9-scu";
> +		reg = <0x1f000000 0x100>;
> +	};
> +
> +	twd_timer: timer at 1f000600 {
> +		compatible = "arm,cortex-a9-twd-timer";
> +		reg = <0x1f000600 0x20>;
> +		interrupt-parent = <&intc>;
> +		interrupts = <1 13 0xf04>;
> +	};
> +
> +	twd_wdog: watchdog at 1f000620 {
> +		compatible = "arm,cortex-a9-twd-wdt";
> +		reg = <0x1f000620 0x20>;
> +		interrupt-parent = <&intc>;
> +		interrupts = <1 14 0xf04>;
> +	};
> +
> +	pmu: pmu at 0 {
> +		compatible = "arm,cortex-a9-pmu";
> +		interrupt-parent = <&intc>;
> +		interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>,
> +			     <0 45 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&CPU0>, <&CPU1>;
> +	};
> +
> +	/* Primary GIC PL390 interrupt controller in the test chip */
> +	intc: interrupt-controller at 1f000000 {
> +		compatible = "arm,cortex-a9-gic";
> +		#interrupt-cells = <3>;
> +		#address-cells = <1>;
> +		interrupt-controller;
> +		reg = <0x1f001000 0x1000>,
> +		      <0x1f000100 0x100>;
> +	};
> +};
> +
> +&ethernet {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&usb {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial2 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&serial3 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&ssp {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&wdog0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&wdog1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer01 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer23 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&gpio2 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&rtc {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer45 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&timer67 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&aaci {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&mmc {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>,
> +		     <0 18 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&kmi0 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&kmi1 {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&clcd {
> +	interrupt-parent = <&intc>;
> +	interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
> +};
> diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm-realview-pbx.dtsi
> new file mode 100644
> index 000000000000..aeb49c4bd773
> --- /dev/null
> +++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
> @@ -0,0 +1,542 @@
> +/*
> + * Copyright 2016 Linaro Ltd
> + *
> + * Permission is hereby granted, free of charge, to any person obtaining a copy
> + * of this software and associated documentation files (the "Software"), to deal
> + * in the Software without restriction, including without limitation the rights
> + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
> + * copies of the Software, and to permit persons to whom the Software is
> + * furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice shall be included in
> + * all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
> + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
> + * THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "skeleton.dtsi"
> +
> +/ {
> +	compatible = "arm,realview-pbx";
> +
> +	chosen { };
> +
> +	aliases {
> +		serial0 = &serial0;
> +		serial1 = &serial1;
> +		serial2 = &serial2;
> +		serial3 = &serial3;
> +		i2c0 = &i2c;
> +	};
> +
> +	memory {
> +		/* 128 MiB memory @ 0x0 */
> +		reg = <0x00000000 0x08000000>;
> +	};
> +
> +	/* The voltage to the MMC card is hardwired at 3.3V */
> +	vmmc: fixedregulator at 0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vmmc";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +        };
> +
> +	veth: fixedregulator at 0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "veth";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +	};
> +
> +	xtal24mhz: xtal24mhz at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <24000000>;
> +	};
> +
> +	refclk32khz: refclk32khz {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <32768>;
> +	};
> +
> +	timclk: timclk at 1M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <24>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	mclk: mclk at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <1>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	kmiclk: kmiclk at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <1>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	sspclk: sspclk at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <1>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	uartclk: uartclk at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <1>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	wdogclk: wdogclk at 24M {
> +		#clock-cells = <0>;
> +		compatible = "fixed-factor-clock";
> +		clock-div = <1>;
> +		clock-mult = <1>;
> +		clocks = <&xtal24mhz>;
> +	};
> +
> +	/* FIXME: this actually hangs off the PLL clocks */
> +	pclk: pclk at 0 {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <0>;
> +	};
> +
> +	flash0 at 40000000 {
> +		/* 2 * 32MiB NOR Flash memory */
> +		compatible = "arm,versatile-flash", "cfi-flash";
> +		reg = <0x40000000 0x04000000>;
> +		bank-width = <4>;
> +	};
> +
> +	flash1 at 44000000 {
> +		/* 2 * 32MiB NOR Flash memory */
> +		compatible = "arm,versatile-flash", "cfi-flash";
> +		reg = <0x44000000 0x04000000>;
> +		bank-width = <4>;
> +	};
> +
> +	/* SMSC 9118 ethernet with PHY and EEPROM */
> +	ethernet: ethernet at 4e000000 {
> +		compatible = "smsc,lan9118", "smsc,lan9115";
> +		reg = <0x4e000000 0x10000>;
> +		phy-mode = "mii";
> +		reg-io-width = <4>;
> +		smsc,irq-active-high;
> +		smsc,irq-push-pull;
> +		vdd33a-supply = <&veth>;
> +		vddvario-supply = <&veth>;
> +	};
> +
> +	usb: usb at 4f000000 {
> +		compatible = "nxp,usb-isp1761";
> +		reg = <0x4f000000 0x20000>;
> +		port1-otg;
> +	};
> +
> +	soc: soc at 0 {
> +		compatible = "arm,realview-pbx-soc", "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		regmap = <&syscon>;
> +		ranges;
> +
> +		syscon: syscon at 10000000 {
> +			compatible = "arm,realview-pbx-syscon", "syscon", "simple-mfd";
> +			reg = <0x10000000 0x1000>;
> +
> +			led at 08.0 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x01>;
> +				label = "versatile:0";
> +				linux,default-trigger = "heartbeat";
> +				default-state = "on";
> +			};
> +			led at 08.1 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x02>;
> +				label = "versatile:1";
> +				linux,default-trigger = "mmc0";
> +				default-state = "off";
> +			};
> +			led at 08.2 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x04>;
> +				label = "versatile:2";
> +				linux,default-trigger = "cpu0";
> +				default-state = "off";
> +			};
> +			led at 08.3 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x08>;
> +				label = "versatile:3";
> +				default-state = "off";
> +			};
> +			led at 08.4 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x10>;
> +				label = "versatile:4";
> +				default-state = "off";
> +			};
> +			led at 08.5 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x20>;
> +				label = "versatile:5";
> +				default-state = "off";
> +			};
> +			led at 08.6 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x40>;
> +				label = "versatile:6";
> +				default-state = "off";
> +			};
> +			led at 08.7 {
> +				compatible = "register-bit-led";
> +				offset = <0x08>;
> +				mask = <0x80>;
> +				label = "versatile:7";
> +				default-state = "off";
> +			};
> +			oscclk0: osc0 at 0c {
> +				compatible = "arm,syscon-icst307";
> +				#clock-cells = <0>;
> +				lock-offset = <0x20>;
> +				vco-offset = <0x0C>;
> +				clocks = <&xtal24mhz>;
> +			};
> +			oscclk1: osc1 at 10 {
> +				compatible = "arm,syscon-icst307";
> +				#clock-cells = <0>;
> +				lock-offset = <0x20>;
> +				vco-offset = <0x10>;
> +				clocks = <&xtal24mhz>;
> +			};
> +			oscclk2: osc2 at 14 {
> +				compatible = "arm,syscon-icst307";
> +				#clock-cells = <0>;
> +				lock-offset = <0x20>;
> +				vco-offset = <0x14>;
> +				clocks = <&xtal24mhz>;
> +			};
> +			oscclk3: osc3 at 18 {
> +				compatible = "arm,syscon-icst307";
> +				#clock-cells = <0>;
> +				lock-offset = <0x20>;
> +				vco-offset = <0x18>;
> +				clocks = <&xtal24mhz>;
> +			};
> +			oscclk4: osc4 at 1c {
> +				compatible = "arm,syscon-icst307";
> +				#clock-cells = <0>;
> +				lock-offset = <0x20>;
> +				vco-offset = <0x1c>;
> +				clocks = <&xtal24mhz>;
> +			};
> +		};
> +
> +		sp810_syscon0: sysctl at 10001000 {
> +			compatible = "arm,sp810", "arm,primecell";
> +			reg = <0x10001000 0x1000>;
> +			clocks = <&refclk32khz>, <&timclk>, <&xtal24mhz>;
> +			clock-names = "refclk", "timclk", "apb_pclk";
> +			#clock-cells = <1>;
> +			clock-output-names = "timerclk0",
> +					     "timerclk1",
> +					     "timerclk2",
> +					     "timerclk3";
> +			assigned-clocks = <&sp810_syscon0 0>,
> +					  <&sp810_syscon0 1>,
> +					  <&sp810_syscon0 2>,
> +					  <&sp810_syscon0 3>;
> +			assigned-clock-parents = <&timclk>,
> +					       <&timclk>,
> +					       <&timclk>,
> +					       <&timclk>;
> +		};
> +
> +		i2c: i2c at 10002000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "arm,versatile-i2c";
> +			reg = <0x10002000 0x1000>;
> +
> +			rtc at 68 {
> +				compatible = "dallas,ds1338";
> +				reg = <0x68>;
> +			};
> +		};
> +
> +		serial0: serial at 10009000 {
> +			compatible = "arm,pl011", "arm,primecell";
> +			reg = <0x10009000 0x1000>;
> +			clocks = <&uartclk>, <&pclk>;
> +			clock-names = "uartclk", "apb_pclk";
> +		};
> +
> +		serial1: serial at 1000a000 {
> +			compatible = "arm,pl011", "arm,primecell";
> +			reg = <0x1000a000 0x1000>;
> +			clocks = <&uartclk>, <&pclk>;
> +			clock-names = "uartclk", "apb_pclk";
> +		};
> +
> +		serial2: serial at 1000b000 {
> +			compatible = "arm,pl011", "arm,primecell";
> +			reg = <0x1000b000 0x1000>;
> +			clocks = <&uartclk>, <&pclk>;
> +			clock-names = "uartclk", "apb_pclk";
> +		};
> +
> +		ssp: ssp at 1000d000 {
> +			compatible = "arm,pl022", "arm,primecell";
> +			reg = <0x1000d000 0x1000>;
> +			clocks = <&sspclk>, <&pclk>;
> +			clock-names = "SSPCLK", "apb_pclk";
> +		};
> +
> +		wdog0: watchdog at 1000f000 {
> +			compatible = "arm,sp805", "arm,primecell";
> +			reg = <0x1000f000 0x1000>;
> +			clocks = <&wdogclk>, <&pclk>;
> +			clock-names = "wdogclk", "apb_pclk";
> +			status = "disabled";
> +		};
> +
> +		wdog1: watchdog at 10010000 {
> +			compatible = "arm,sp805", "arm,primecell";
> +			reg = <0x10010000 0x1000>;
> +			clocks = <&wdogclk>, <&pclk>;
> +			clock-names = "wdogclk", "apb_pclk";
> +			status = "disabled";
> +		};
> +
> +		timer01: timer at 10011000 {
> +			compatible = "arm,sp804", "arm,primecell";
> +			reg = <0x10011000 0x1000>;
> +			clocks = <&sp810_syscon0 0>,
> +			         <&sp810_syscon0 1>,
> +				 <&pclk>;
> +			clock-names = "timerclk0",
> +				    "timerclk1",
> +				    "apb_pclk";
> +		};
> +
> +		timer23: timer at 10012000 {
> +			compatible = "arm,sp804", "arm,primecell";
> +			reg = <0x10012000 0x1000>;
> +			clocks = <&sp810_syscon0 2>,
> +			         <&sp810_syscon0 3>,
> +				 <&pclk>;
> +			clock-names = "timerclk2",
> +				    "timerclk3",
> +				    "apb_pclk";
> +		};
> +
> +		gpio0: gpio at 10013000 {
> +			compatible = "arm,pl061", "arm,primecell";
> +			reg = <0x10013000 0x1000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			clocks = <&pclk>;
> +			clock-names = "apb_pclk";
> +		};
> +
> +		gpio1: gpio at 10014000 {
> +			compatible = "arm,pl061", "arm,primecell";
> +			reg = <0x10014000 0x1000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			clocks = <&pclk>;
> +			clock-names = "apb_pclk";
> +		};
> +
> +		gpio2: gpio at 10015000 {
> +			compatible = "arm,pl061", "arm,primecell";
> +			reg = <0x10015000 0x1000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			clocks = <&pclk>;
> +			clock-names = "apb_pclk";
> +		};
> +
> +		/* DVI serial bus control is at 10016000 */
> +
> +		rtc: rtc at 10017000 {
> +			compatible = "arm,pl031", "arm,primecell";
> +			reg = <0x10017000 0x1000>;
> +			clocks = <&pclk>;
> +			clock-names = "apb_pclk";
> +		};
> +
> +		timer45: timer at 10018000 {
> +			compatible = "arm,sp804", "arm,primecell";
> +			reg = <0x10018000 0x1000>;
> +			clocks = <&timclk>, <&timclk>, <&pclk>;
> +			clock-names = "timerclk4", "timerclk5", "apb_pclk";
> +		};
> +
> +		timer67: timer at 10019000 {
> +			compatible = "arm,sp804", "arm,primecell";
> +			reg = <0x10019000 0x1000>;
> +			clocks = <&timclk>, <&timclk>, <&pclk>;
> +			clock-names = "timerclk6", "timerclk7", "apb_pclk";
> +		};
> +
> +		sp810_syscon1: sysctl at 1001a000 {
> +			compatible = "arm,sp810", "arm,primecell";
> +			reg = <0x1001a000 0x1000>;
> +			clocks = <&refclk32khz>, <&timclk>, <&xtal24mhz>;
> +			clock-names = "refclk", "timclk", "apb_pclk";
> +			#clock-cells = <1>;
> +			clock-output-names = "timerclk4",
> +					     "timerclk5",
> +					     "timerclk6",
> +					     "timerclk7";
> +			assigned-clocks = <&sp810_syscon1 0>,
> +					  <&sp810_syscon1 1>,
> +					  <&sp810_syscon1 2>,
> +					  <&sp810_syscon1 3>;
> +			assigned-clock-parents = <&timclk>,
> +					       <&timclk>,
> +					       <&timclk>,
> +					       <&timclk>;
> +		};
> +	};
> +
> +
> +	/* These peripherals are inside the FPGA */
> +	fpga {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		aaci: aaci at 10004000 {
> +			compatible = "arm,pl041", "arm,primecell";
> +			reg = <0x10004000 0x1000>;
> +			clocks = <&pclk>;
> +			clock-names = "apb_pclk";
> +		};
> +
> +		mmc: mmcsd at 10005000 {
> +			compatible = "arm,pl18x", "arm,primecell";
> +			reg = <0x10005000 0x1000>;
> +
> +			/* Due to frequent FIFO overruns, use just 500 kHz */
> +			max-frequency = <500000>;
> +			bus-width = <4>;
> +			cap-sd-highspeed;
> +			cap-mmc-highspeed;
> +			clocks = <&mclk>, <&pclk>;
> +			clock-names = "mclk", "apb_pclk";
> +			vmmc-supply = <&vmmc>;
> +			cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> +			wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		kmi0: kmi at 10006000 {
> +			compatible = "arm,pl050", "arm,primecell";
> +			reg = <0x10006000 0x1000>;
> +			clocks = <&kmiclk>, <&pclk>;
> +			clock-names = "KMIREFCLK", "apb_pclk";
> +		};
> +
> +		kmi1: kmi at 10007000 {
> +			compatible = "arm,pl050", "arm,primecell";
> +			reg = <0x10007000 0x1000>;
> +			clocks = <&kmiclk>, <&pclk>;
> +			clock-names = "KMIREFCLK", "apb_pclk";
> +		};
> +
> +		serial3: serial at 1000c000 {
> +			compatible = "arm,pl011", "arm,primecell";
> +			reg = <0x1000c000 0x1000>;
> +			clocks = <&uartclk>, <&pclk>;
> +			clock-names = "uartclk", "apb_pclk";
> +		};
> +	};
> +
> +	/* These peripherals are inside the NEC ISSP */
> +	issp {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		clcd: clcd at 10020000 {
> +			compatible = "arm,pl111", "arm,primecell";
> +			reg = <0x10020000 0x1000>;
> +			interrupt-names = "combined";
> +			clocks = <&oscclk4>, <&pclk>;
> +			clock-names = "clcdclk", "apb_pclk";
> +
> +			port {
> +				clcd_pads: endpoint {
> +					remote-endpoint = <&clcd_panel>;
> +					arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
> +				};
> +			};
> +
> +			panel {
> +				compatible = "panel-dpi";
> +
> +				port {
> +					clcd_panel: endpoint {
> +						remote-endpoint = <&clcd_pads>;
> +					};
> +				};
> +
> +				/* Standard 640x480 VGA timings */
> +				panel-timing {
> +					clock-frequency = <25175000>;
> +					hactive = <640>;
> +					hback-porch = <48>;
> +					hfront-porch = <16>;
> +					hsync-len = <96>;
> +					vactive = <480>;
> +					vback-porch = <33>;
> +					vfront-porch = <10>;
> +					vsync-len = <2>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
>