From: nicolas.ferre@atmel.com (Nicolas Ferre)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
Date: Tue, 1 Mar 2016 11:12:10 +0100 [thread overview]
Message-ID: <56D56AFA.6050605@atmel.com> (raw)
In-Reply-To: <1453825818-25217-1-git-send-email-nicolas.ferre@atmel.com>
Le 26/01/2016 17:30, Nicolas Ferre a ?crit :
> The dmas/dma-names properties are added to the UART nodes. Note that additional
> properties are needed to enable them at the board level: check bindings for
> details.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Added to at91-4.6-dt.
Bye,
> ---
> arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
> index 3f750f6170f2..82d0c19e9720 100644
> --- a/arch/arm/boot/dts/sama5d2.dtsi
> +++ b/arch/arm/boot/dts/sama5d2.dtsi
> @@ -880,6 +880,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf801c000 0x100>;
> interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(35))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(36))>;
> + dma-names = "tx", "rx";
> clocks = <&uart0_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -889,6 +896,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8020000 0x100>;
> interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(37))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(38))>;
> + dma-names = "tx", "rx";
> clocks = <&uart1_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -898,6 +912,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8024000 0x100>;
> interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(39))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(40))>;
> + dma-names = "tx", "rx";
> clocks = <&uart2_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1016,6 +1037,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc008000 0x100>;
> interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(41))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(42))>;
> + dma-names = "tx", "rx";
> clocks = <&uart3_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1024,6 +1052,13 @@
> uart4: serial at fc00c000 {
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc00c000 0x100>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(43))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(44))>;
> + dma-names = "tx", "rx";
> interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
> clocks = <&uart4_clk>;
> clock-names = "usart";
>
--
Nicolas Ferre
WARNING: multiple messages have this Message-ID (diff)
From: Nicolas Ferre <nicolas.ferre@atmel.com>
To: Alexandre Belloni <alexandre.belloni@free-electrons.com>,
<linux-arm-kernel@lists.infradead.org>
Cc: <linux-kernel@vger.kernel.org>,
Ludovic Desroches <ludovic.desroches@atmel.com>,
Cyrille Pitchen <cyrille.pitchen@atmel.com>
Subject: Re: [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
Date: Tue, 1 Mar 2016 11:12:10 +0100 [thread overview]
Message-ID: <56D56AFA.6050605@atmel.com> (raw)
In-Reply-To: <1453825818-25217-1-git-send-email-nicolas.ferre@atmel.com>
Le 26/01/2016 17:30, Nicolas Ferre a écrit :
> The dmas/dma-names properties are added to the UART nodes. Note that additional
> properties are needed to enable them at the board level: check bindings for
> details.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Added to at91-4.6-dt.
Bye,
> ---
> arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
> index 3f750f6170f2..82d0c19e9720 100644
> --- a/arch/arm/boot/dts/sama5d2.dtsi
> +++ b/arch/arm/boot/dts/sama5d2.dtsi
> @@ -880,6 +880,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf801c000 0x100>;
> interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(35))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(36))>;
> + dma-names = "tx", "rx";
> clocks = <&uart0_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -889,6 +896,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8020000 0x100>;
> interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(37))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(38))>;
> + dma-names = "tx", "rx";
> clocks = <&uart1_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -898,6 +912,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8024000 0x100>;
> interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(39))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(40))>;
> + dma-names = "tx", "rx";
> clocks = <&uart2_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1016,6 +1037,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc008000 0x100>;
> interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(41))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(42))>;
> + dma-names = "tx", "rx";
> clocks = <&uart3_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1024,6 +1052,13 @@
> uart4: serial@fc00c000 {
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc00c000 0x100>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(43))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(44))>;
> + dma-names = "tx", "rx";
> interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
> clocks = <&uart4_clk>;
> clock-names = "usart";
>
--
Nicolas Ferre
next prev parent reply other threads:[~2016-03-01 10:12 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-26 16:30 [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes Nicolas Ferre
2016-01-26 16:30 ` Nicolas Ferre
2016-03-01 10:12 ` Nicolas Ferre [this message]
2016-03-01 10:12 ` Nicolas Ferre
-- strict thread matches above, loose matches on Subject: below --
2017-03-27 9:09 Alexandre Belloni
2017-03-27 9:09 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56D56AFA.6050605@atmel.com \
--to=nicolas.ferre@atmel.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.