From: Michael Haas <haas@computerlinguist.org>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] Add CONFIG_GMAC_TX_DELAY=4 for OlinuXino Lime2
Date: Sat, 19 Mar 2016 10:35:49 +0100 [thread overview]
Message-ID: <56ED1D75.50008@computerlinguist.org> (raw)
In-Reply-To: <56ED1C96.30708@redhat.com>
On 03/19/2016 10:32 AM, Hans de Goede wrote:
> Hi,
>
> On 19-03-16 09:39, Fran?ois-David Collin wrote:
>> Hi,
>>
>> As I?m banging my head on this too, please allow me to provide some
>> details
>> I got two stable situations :
>> The Lime2 is connected directly to the Gbit interface of my laptop,
>> speed are OK:
>
> Michael Haas' work to debug this by looking at the phy registers
> seems to be the most promising so-far, the clk reg and axp209
> registers all seem to be identical between good and bad setups.
>
> Can you try to:
>
> 1) Stop the boot in u-boot (press a key on the serial console)
> 2) Bring up the network, e.g. type "dhcp" then ctrl+c when it tries
> to tftp
> 3) Do: "mii read 1 0x11" in u-boot and record the output ?
>
> Regards,
>
> Hans
I am currently (as I write this email) looking at the full set of
registers for the PHY, including the additional
pages:
setenv miipagedump 'for page in 0x0 0x01 0x02 0x03 0x04 0x05 0x06 0x07;
do echo "page $page"; mii write 1 0x1f $page; run miidump; done; mii
write 1 0x1f 0x00'
setenv miireadable 'setenv x 0x0; while test $x -le 5; do echo $x; mii
dump 1 $x; setexpr x $x + 1; done'
setenv miidump 'setenv x 0x0; while test $x -le 31; do echo $x; mii read
1 $x; setexpr x $x + 1; done'
setenv pmicdump 'i2c md 0x34 0xff'
setenv clkdump 'md 0x1c20164'
setenv doboot 'run pmicdump; run clkdump; setenv bootargs
console=ttyS0,115200 rootwait panic=10; setenv autoload no;dhcp; run
miireadable; run miipagedump; setenv serverip 192.168.1.170;tftpboot
${scriptaddr} /debian-installer/armhf/tftpboot.scr;source ${scriptaddr}'
No results as of yet, but I have yet to do a run where I successfully
dump all extpages.. the script was off before hand. Some registers were
different between working and non-working runs, but these were mostly
reserved. I will be posting a full log later on.
Interesting: 01c20224 is 14888022 for broken runs and 14888021 on
working runs - but I have not verified this extensively.
I'm hanging out as 'laga' in #u-boot.
Michael
Another
next prev parent reply other threads:[~2016-03-19 9:35 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-15 5:41 [U-Boot] [PATCH] Add CONFIG_GMAC_TX_DELAY=4 for OlinuXino Lime2 Michael Haas
[not found] ` <20160315180914.GA1878@excalibur.cnev.de>
2016-03-15 20:41 ` Tom Rini
2016-03-16 8:32 ` Michael Haas
2016-03-16 9:29 ` Hans de Goede
2016-03-16 10:53 ` Hans de Goede
[not found] ` <20160316203642.GC1817@excalibur.cnev.de>
2016-03-17 5:28 ` Michael Haas
2016-03-17 10:52 ` Hans de Goede
2016-03-17 21:53 ` Michael Haas
2016-03-18 7:41 ` Hans de Goede
[not found] ` <20160318190220.GC1815@excalibur.cnev.de>
2016-03-18 19:06 ` Michael Haas
2016-03-20 8:36 ` Michael Haas
2016-03-20 10:05 ` François-David Collin
2016-03-18 20:32 ` Michael Haas
2016-03-18 21:53 ` Michael Haas
2016-03-19 8:39 ` François-David Collin
2016-03-19 9:32 ` Hans de Goede
2016-03-19 9:35 ` Michael Haas [this message]
2016-03-19 9:45 ` Michael Haas
2016-03-19 13:40 ` Michael Haas
2016-03-19 14:35 ` François-David Collin
2016-03-20 13:45 ` Hans de Goede
2016-03-20 15:28 ` Michael Haas
2016-03-20 18:51 ` Hans de Goede
[not found] ` <20160321154714.GA4751@excalibur.cnev.de>
2016-03-21 18:57 ` Michael Haas
2016-03-21 20:59 ` Hans de Goede
2016-03-21 21:01 ` Hans de Goede
2016-03-21 21:47 ` Michael Haas
2016-03-21 22:00 ` Hans de Goede
2016-03-22 5:12 ` Michael Haas
2016-03-22 8:46 ` Peter Korsgaard
2016-03-22 8:57 ` Hans de Goede
2016-03-22 9:01 ` Michael Haas
2016-03-22 9:50 ` Peter Korsgaard
[not found] ` <20160321173000.GD4751@excalibur.cnev.de>
2016-03-21 20:56 ` Hans de Goede
-- strict thread matches above, loose matches on Subject: below --
2016-03-18 17:33 François-David Collin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56ED1D75.50008@computerlinguist.org \
--to=haas@computerlinguist.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.