[U-Boot] Latest U-boot branch not booting on Hummingbird A31

[Hans de Goede <hdegoede@redhat.com>]

HI,

On 21-03-16 10:49, wens Tsai wrote:
> Hi Hans,
>
> I updated U-boot on my boards to your latest sunxi-wip branch:
>
>      f965340 ("sunxi: Enable support for the eMMC found on the orangepi plus")
>
> My Hummingbird A31 fails to boot after this. See log:
>
> HELLO! BOOT0 is starting!
> boot0 version : 3.0.0
> reg_addr 0x01f00100 =0x00000000
> reg_addr 0x01f00104 =0x00000000
> reg_addr 0x01f00108 =0x00000000
> reg_addr 0x01f0010c =0x00000000
> reg_addr 0x01f00110 =0x00000000
> reg_addr 0x01f00114 =0x00000000
> [DRAM]ver 1.03 clk = 312
> cpu 0 pmu 0
> dram size =1024
> sum=0x31776fa8
> src_sum=0x31776fa8
> Ready to disable icache.
> Jump to secend Boot.
> [      0.209]
>
> U-Boot 2011.09-rc1 (Jun 17 2014 - 17:30:56) Allwinner Technology
>
> [      0.217]version: 1.1.0
> [      0.220]pmbus:   ready
> [      0.222]PMU: AXP221
> [      0.225]PMU: AXP22x found
> [      0.227]PMU: bat ratio = 100
> [      0.231]PMU: dcdc3 1260
> [      0.233]PMU: pll1 1008 Mhz
> dcdc1_vol = 3000
> dcdc2_vol = 1200
> dcdc3_vol = 1260
> dcdc4_vol = 1200
> dcdc5_vol = 1500
> aldo1_vol = 3000
> aldo2_vol = 1800
> aldo3_vol = 3000
> eldo3_vol = 1800
> find power_sply to end
> fel key old mode
> run key detect
> no key found
> no key input
> dram_para_set start
> dram_para_set end
> [      0.277]DRAM:  1 GiB
> relocation Offset is: 15b25000
> donn't initialize ther user_gpio (main_key:boot_init_gpio)
> deu_mode1 not exist.
> lcdgamma4iep for lcd1 not exist.
> DRV_DISP_Init: opened
> [      0.542]fetch script data boot_disp.output_type fail
> [      0.547]fetch script data boot_disp.output_mode fail
> [      0.552]fetch script data boot_disp.auto_hpd fail
> [      0.557]lcd0_para.lcd_used=1
> workmode = 0
> [      0.603]NAND: NAND_UbootInit
> NB1 : enter NAND_LogicInit
> not burn nand partition table!
> NB1 : nftl num: 2
>   init nftl: 0
> NB1 : NAND_LogicInit ok, result = 0x0
> [      1.268]sunxi flash init ok
> probe mmc0 if exist
> SUNXI SD/MMC: 0
> Man 1d4144 Snr d3602657
> SD
> 0.2
> boot0 capacity: 0KB,boot1 capacity: 0KB
> boot0 magic = eGON.BT0??
> set next system status
> DRV_DISP_Exit: closed
> sunxi_board_close_source
> NAND_UbootExit
> NB1 : NAND_LogicExit
> reset cpu
> HELLO! BOOT0 is starting!
> boot0 version : 3.0.0
> reg_addr 0x01f00100 =0x00007347
> reg_addr 0x01f00104 =0x0000703b
> reg_addr 0x01f00108 =0x5aa5a55a
> reg_addr 0x01f0010c =0x000000ff
> reg_addr 0x01f00110 =0x000000ff
> reg_addr 0x01f00114 =0x000000ff
> eraly jump fel
>
> U-Boot SPL 2016.03-00320-geeea041 (Mar 21 2016 - 15:16:34)
> DRAM: 1024 MiB
> Trying to boot from MMC1
>
>
> and hangs...
>
> geeea041 is the SinA31s patch I have on top of your sunxi-wip branch.
>
> I bisected it down to 107fb76 ("sunxi: Fix gmac not working due to
> cpu_eth_init no longer being called"). Not sure why this commit fails though.

Hmm, can you try commenting out these 2 lines in arch/arm/cpu/armv7/sunxi/board.c :

#ifdef CONFIG_MACPWR
         gpio_request(CONFIG_MACPWR, "macpwr");
         gpio_direction_output(CONFIG_MACPWR, 1);
#endif

Around line 103 ? That is the only bit which has changed in
the SPL path due to this patch.

Regards,

Hans




>
>
> Regards
> ChenYu
>