[PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[christopher.spinrath at rwth-aachen.de]

From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>

The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
---

Changes since v1:
 - remove regulator pseudo-bus
 - remove partition layout from spi flash node
 - remove unneeded label of the spi flash node
 - convert downstream power-on-gpio property of pcie node to a proper
   regulator
 - sort usb* related nodes alphabetically
 - make use of GPIO_ACTIVE_{LOW,HIGH} defines
 - replace 0x80000000 iomuxc configs by proper defaults obtained from
   u-boot

 arch/arm/boot/dts/imx6q-cm-fx6.dts | 125 +++++++++++++++++++++++++++++++++++++
 1 file changed, 125 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index 21c513f..c6f0e58 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -12,6 +12,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6q.dtsi"
 
 / {
@@ -31,6 +32,49 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	reg_pcie_power_on_gpio: regulator-pcie-power-on-gpio {
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-pcie-power-on-gpio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: usb_h1_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: usb_otg_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	m25p80 at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
 };
 
 &fec {
@@ -46,7 +90,30 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+	clock-frequency = <100000>;
+
+	eeprom at 50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
 &iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK	0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO	0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI	0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30	0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x100b1
+		>;
+	};
+
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
@@ -90,12 +157,55 @@
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x1b0b1
+		>;
+	};
+
 	pinctrl_uart4: uart4grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
 			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
 		>;
 	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x130b0
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&reg_pcie_power_on_gpio>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
 };
 
 &uart4 {
@@ -103,3 +213,18 @@
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 };
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	status = "okay";
+};
-- 
2.8.3

[PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg]

From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>

The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.

Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
---

Changes since v1:
 - remove regulator pseudo-bus
 - remove partition layout from spi flash node
 - remove unneeded label of the spi flash node
 - convert downstream power-on-gpio property of pcie node to a proper
   regulator
 - sort usb* related nodes alphabetically
 - make use of GPIO_ACTIVE_{LOW,HIGH} defines
 - replace 0x80000000 iomuxc configs by proper defaults obtained from
   u-boot

 arch/arm/boot/dts/imx6q-cm-fx6.dts | 125 +++++++++++++++++++++++++++++++++++++
 1 file changed, 125 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index 21c513f..c6f0e58 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -12,6 +12,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx6q.dtsi"
 
 / {
@@ -31,6 +32,49 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	reg_pcie_power_on_gpio: regulator-pcie-power-on-gpio {
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-pcie-power-on-gpio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: usb_h1_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: usb_otg_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
 };
 
 &fec {
@@ -46,7 +90,30 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+	clock-frequency = <100000>;
+
+	eeprom@50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
 &iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK	0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO	0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI	0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30	0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x100b1
+		>;
+	};
+
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
@@ -90,12 +157,55 @@
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x1b0b1
+		>;
+	};
+
 	pinctrl_uart4: uart4grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
 			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
 		>;
 	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x130b0
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&reg_pcie_power_on_gpio>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
 };
 
 &uart4 {
@@ -103,3 +213,18 @@
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 };
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	status = "okay";
+};
-- 
2.8.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[Fabio Estevam]

On Sun, Jun 5, 2016 at 3:26 PM,  <christopher.spinrath@rwth-aachen.de> wrote:

> +&pcie {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_pcie>;
> +       reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;

I suppose this should be active low, right?

With this fixed:

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Re: [PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[Fabio Estevam]

On Sun, Jun 5, 2016 at 3:26 PM,  <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org> wrote:

> +&pcie {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_pcie>;
> +       reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;

I suppose this should be active low, right?

With this fixed:

Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[Christopher Spinrath]

Hi Fabio,

Thanks for your review!

On 06/05/2016 09:14 PM, Fabio Estevam wrote:
> On Sun, Jun 5, 2016 at 3:26 PM,  <christopher.spinrath@rwth-aachen.de> wrote:
> 
>> +&pcie {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_pcie>;
>> +       reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> 
> I suppose this should be active low, right?
> 
hmm, the vendor devicetree uses active high but does not set
reset-gpio-active-high. In a quick test it turned out that setting this
property keeps the pci bus in reset.
In fact, the linux driver ignores the polarity and falls back to active
low. This explains why specifying active high "worked" here...

So you are right and it should be active low. I'll fix that.

> With this fixed:
> 
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
> 

Thanks,
Christopher

Re: [PATCH v2 2/4] ARM: dts: imx6q: extend support for the cm-fx6

[Christopher Spinrath]

Hi Fabio,

Thanks for your review!

On 06/05/2016 09:14 PM, Fabio Estevam wrote:
> On Sun, Jun 5, 2016 at 3:26 PM,  <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org> wrote:
> 
>> +&pcie {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_pcie>;
>> +       reset-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> 
> I suppose this should be active low, right?
> 
hmm, the vendor devicetree uses active high but does not set
reset-gpio-active-high. In a quick test it turned out that setting this
property keeps the pci bus in reset.
In fact, the linux driver ignores the polarity and falls back to active
low. This explains why specifying active high "worked" here...

So you are right and it should be active low. I'll fix that.

> With this fixed:
> 
> Reviewed-by: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
> 

Thanks,
Christopher
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 3/4] ARM: dts: imx6q: add support for the Utilite Pro

[christopher.spinrath at rwth-aachen.de]

From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>

The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.

Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
---

Changes since v1:
 - use GPL/X11 dual license (in agreement with CompuLab)
 - use GPIO_ACTIVE_{LOW,HIGH} defines to specify gpios
 - use KEY_POWER define for the power key
 - replace 0x80000000 iomuxc configs by proper defaults
   obtained from u-boot
 - remove iomuxc container node
 - iomuxc: remove hog group and move the gpio-key pins
   to a proper gpio_keys group
 - clean up uart2 node (remove dma properties already
   present in imx6qdl.dtsi and replace deprecated
   fsl,uart-has-rtscts by the generic one)

 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/imx6q-utilite-pro.dts | 153 ++++++++++++++++++++++++++++++++
 2 files changed, 154 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-utilite-pro.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 515a428..287044c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -369,6 +369,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-tx6q-1110.dtb \
 	imx6q-tx6q-11x0-mb7.dtb \
 	imx6q-udoo.dtb \
+	imx6q-utilite-pro.dtb \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
 	imx6qp-nitrogen6_max.dtb \
diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/imx6q-utilite-pro.dts
new file mode 100644
index 0000000..7219745
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-utilite-pro.dts
@@ -0,0 +1,153 @@
+/*
+ * Copyright 2013 CompuLab Ltd.
+ * Copyright 2016 Christopher Spinrath
+ *
+ * Based on the devicetree distributed with the vendor kernel for the
+ * Utilite Pro:
+ *	Copyright 2013 CompuLab Ltd.
+ *	Author: Valentin Raevsky <valentin@compulab.co.il>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "imx6q-cm-fx6.dts"
+
+/ {
+	model = "CompuLab Utilite Pro";
+	compatible = "compulab,utilite-pro", "compulab,cm-fx6", "fsl,imx6q";
+
+	aliases {
+		ethernet1 = &eth1;
+		rtc0 = &em3027;
+		rtc1 = &snvs_rtc;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	eeprom at 50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	em3027: rtc at 56 {
+		compatible = "emmicro,em3027";
+		reg = <0x56>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_GPIO_8__UART2_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+		>;
+	};
+};
+
+&pcie {
+	pcie at 0,0 {
+		reg = <0x000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		/* non-removable i211 ethernet card */
+		eth1: intel,i211 at pcie0,0 {
+			reg = <0x010000 0 0 0 0>;
+		};
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
-- 
2.8.3

[PATCH v2 3/4] ARM: dts: imx6q: add support for the Utilite Pro

[christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg]

From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>

The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.

Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.

Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
Cc: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
---

Changes since v1:
 - use GPL/X11 dual license (in agreement with CompuLab)
 - use GPIO_ACTIVE_{LOW,HIGH} defines to specify gpios
 - use KEY_POWER define for the power key
 - replace 0x80000000 iomuxc configs by proper defaults
   obtained from u-boot
 - remove iomuxc container node
 - iomuxc: remove hog group and move the gpio-key pins
   to a proper gpio_keys group
 - clean up uart2 node (remove dma properties already
   present in imx6qdl.dtsi and replace deprecated
   fsl,uart-has-rtscts by the generic one)

 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/imx6q-utilite-pro.dts | 153 ++++++++++++++++++++++++++++++++
 2 files changed, 154 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-utilite-pro.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 515a428..287044c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -369,6 +369,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-tx6q-1110.dtb \
 	imx6q-tx6q-11x0-mb7.dtb \
 	imx6q-udoo.dtb \
+	imx6q-utilite-pro.dtb \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
 	imx6qp-nitrogen6_max.dtb \
diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/imx6q-utilite-pro.dts
new file mode 100644
index 0000000..7219745
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-utilite-pro.dts
@@ -0,0 +1,153 @@
+/*
+ * Copyright 2013 CompuLab Ltd.
+ * Copyright 2016 Christopher Spinrath
+ *
+ * Based on the devicetree distributed with the vendor kernel for the
+ * Utilite Pro:
+ *	Copyright 2013 CompuLab Ltd.
+ *	Author: Valentin Raevsky <valentin-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "imx6q-cm-fx6.dts"
+
+/ {
+	model = "CompuLab Utilite Pro";
+	compatible = "compulab,utilite-pro", "compulab,cm-fx6", "fsl,imx6q";
+
+	aliases {
+		ethernet1 = &eth1;
+		rtc0 = &em3027;
+		rtc1 = &snvs_rtc;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "at24,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	em3027: rtc@56 {
+		compatible = "emmicro,em3027";
+		reg = <0x56>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_GPIO_8__UART2_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+		>;
+	};
+};
+
+&pcie {
+	pcie@0,0 {
+		reg = <0x000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		/* non-removable i211 ethernet card */
+		eth1: intel,i211@pcie0,0 {
+			reg = <0x010000 0 0 0 0>;
+		};
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
-- 
2.8.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 3/4] ARM: dts: imx6q: add support for the Utilite Pro

[Igor Grinberg]

On 06/05/2016 09:26 PM, christopher.spinrath at rwth-aachen.de wrote:
> From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
> 
> The CompuLab Utilite Pro is a miniature fanless desktop pc based on
> the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
> USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
> DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
> 
> Add initial support for it including USB, Ethernet (both ports), sata
> and HDMI support.
> 
> Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
> Cc: Igor Grinberg <grinberg@compulab.co.il>

Acked-by: Igor Grinberg <grinberg@compulab.co.il>

-- 
Regards,
Igor.

Re: [PATCH v2 3/4] ARM: dts: imx6q: add support for the Utilite Pro

[Igor Grinberg]

On 06/05/2016 09:26 PM, christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org wrote:
> From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
> 
> The CompuLab Utilite Pro is a miniature fanless desktop pc based on
> the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
> USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
> DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
> 
> Add initial support for it including USB, Ethernet (both ports), sata
> and HDMI support.
> 
> Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
> Cc: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>

Acked-by: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>

-- 
Regards,
Igor.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[christopher.spinrath at rwth-aachen.de]

From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>

GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
licensed under GPLv2/X11.

Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
---

Changes since v1:
 - new patch in v2; without it the dual licensed of the imx6q-utilite-pro.dts
   is not really useful because it includes imx6q-cm-fx6.dts.

 arch/arm/boot/dts/imx6q-cm-fx6.dts | 40 +++++++++++++++++++++++++++++++++-----
 1 file changed, 35 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index c6f0e58..fe2c868 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -3,12 +3,42 @@
  *
  * Author: Valentin Raevsky <valentin@compulab.co.il>
  *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
  *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
-- 
2.8.3

[PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg]

From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>

GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
licensed under GPLv2/X11.

Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.

Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
Cc: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
---

Changes since v1:
 - new patch in v2; without it the dual licensed of the imx6q-utilite-pro.dts
   is not really useful because it includes imx6q-cm-fx6.dts.

 arch/arm/boot/dts/imx6q-cm-fx6.dts | 40 +++++++++++++++++++++++++++++++++-----
 1 file changed, 35 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index c6f0e58..fe2c868 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -3,12 +3,42 @@
  *
  * Author: Valentin Raevsky <valentin-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
  *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
  *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
-- 
2.8.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[Igor Grinberg]

Hi Christopher,

On 06/05/2016 09:26 PM, christopher.spinrath at rwth-aachen.de wrote:
> From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
> 
> GPLv2-only devicetrees make reuse difficult for software components
> licensed under a different license. In particular, the Utilite Pro
> devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
                                               ^^^
That's a downgrade ;-)
With the above fixed, please add my ack below.

> licensed under GPLv2/X11.
> 
> Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.

Off topic of this patch, I think SPDX works much better than having
this huge license "hat" in each file.

> 
> Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
> Cc: Igor Grinberg <grinberg@compulab.co.il>

Acked-by: Igor Grinberg <grinberg@compulab.co.il>

> ---
> 
> Changes since v1:
>  - new patch in v2; without it the dual licensed of the imx6q-utilite-pro.dts
>    is not really useful because it includes imx6q-cm-fx6.dts.
> 
>  arch/arm/boot/dts/imx6q-cm-fx6.dts | 40 +++++++++++++++++++++++++++++++++-----
>  1 file changed, 35 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
> index c6f0e58..fe2c868 100644
> --- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
> +++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
> @@ -3,12 +3,42 @@
>   *
>   * Author: Valentin Raevsky <valentin@compulab.co.il>
>   *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 or later at the following locations:
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
>   *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
>   */
>  
>  /dts-v1/;
> 

-- 
Regards,
Igor.

Re: [PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[Igor Grinberg]

Hi Christopher,

On 06/05/2016 09:26 PM, christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org wrote:
> From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
> 
> GPLv2-only devicetrees make reuse difficult for software components
> licensed under a different license. In particular, the Utilite Pro
> devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
                                               ^^^
That's a downgrade ;-)
With the above fixed, please add my ack below.

> licensed under GPLv2/X11.
> 
> Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.

Off topic of this patch, I think SPDX works much better than having
this huge license "hat" in each file.

> 
> Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
> Cc: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>

Acked-by: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>

> ---
> 
> Changes since v1:
>  - new patch in v2; without it the dual licensed of the imx6q-utilite-pro.dts
>    is not really useful because it includes imx6q-cm-fx6.dts.
> 
>  arch/arm/boot/dts/imx6q-cm-fx6.dts | 40 +++++++++++++++++++++++++++++++++-----
>  1 file changed, 35 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
> index c6f0e58..fe2c868 100644
> --- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
> +++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
> @@ -3,12 +3,42 @@
>   *
>   * Author: Valentin Raevsky <valentin-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
>   *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 or later at the following locations:
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
>   *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
>   */
>  
>  /dts-v1/;
> 

-- 
Regards,
Igor.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[Christopher Spinrath]

Hi Igor,

On 06/06/2016 09:53 AM, Igor Grinberg wrote:
> Hi Christopher,
> 
> On 06/05/2016 09:26 PM, christopher.spinrath at rwth-aachen.de wrote:
>> From: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
>>
>> GPLv2-only devicetrees make reuse difficult for software components
>> licensed under a different license. In particular, the Utilite Pro
>> devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
>                                                ^^^
> That's a downgrade ;-)
> With the above fixed, please add my ack below.
> 

uups, I will fix it.

Thanks,
Christopher

>> licensed under GPLv2/X11.
>>
>> Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
> 
> Off topic of this patch, I think SPDX works much better than having
> this huge license "hat" in each file.
> 
>>
>> Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
>> Cc: Igor Grinberg <grinberg@compulab.co.il>
> 
> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
> 

[...]

Re: [PATCH v2 4/4] ARM: dts: imx6q-cm-fx6: Relicense under GPLv2/X11

[Christopher Spinrath]

Hi Igor,

On 06/06/2016 09:53 AM, Igor Grinberg wrote:
> Hi Christopher,
> 
> On 06/05/2016 09:26 PM, christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org wrote:
>> From: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
>>
>> GPLv2-only devicetrees make reuse difficult for software components
>> licensed under a different license. In particular, the Utilite Pro
>> devicetree file (which includes on imx6q-cm-fx5.dts) is already dual
>                                                ^^^
> That's a downgrade ;-)
> With the above fixed, please add my ack below.
> 

uups, I will fix it.

Thanks,
Christopher

>> licensed under GPLv2/X11.
>>
>> Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
> 
> Off topic of this patch, I think SPDX works much better than having
> this huge license "hat" in each file.
> 
>>
>> Signed-off-by: Christopher Spinrath <christopher.spinrath-vA1bhqPz9FBZXbeN9DUtxg@public.gmane.org>
>> Cc: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
> 
> Acked-by: Igor Grinberg <grinberg-UTxiZqZC01RS1MOuV/RT9w@public.gmane.org>
> 

[...]
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html