Which is the correct BSP to use for a freescale LS1021A-IOT development kit?

Which is the correct BSP to use for a freescale LS1021A-IOT development kit?

[Thomas A. F. Thorne MEng AUS MIET]

[-- Attachment #1.1.1: Type: text/plain, Size: 720 bytes --]

Good afternoon,

I have a freescale LS1021A-IOT development board and was wondering if
the meta-fsl-arm layer was the correct board support package for it?  I
can see the ls1021atwr.conf in  meta-fsl-arm/conf/machine/ which targets
the ls102xa chipset so it seems likely to be the correct one. 

What makes me wonder if it the correct one is that there is a dedicated
ls1021aiot.conf in the meta-fsl-arm layer provided by the LS1021A-IOT
SDK found at
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-arm-processors/qoriq-ls1021a-iot-gateway-reference-design:LS1021A-IoT?fpsp=1&tab=Design_Tools_Tab


Regards, Tom

-- 
Thomas Thorne  Software Engineer  Net2Edge Limited


[-- Attachment #1.1.2: Type: text/html, Size: 1327 bytes --]

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 484 bytes --]

Re: Which is the correct BSP to use for a freescale LS1021A-IOT development kit?

[Zhenhua Luo]

[-- Attachment #1: Type: text/plain, Size: 1234 bytes --]

Hello Tom,

The meta-fsl-arm layer in Yocto git repo only supports ls1021atwr. To support ls1021a-iot board, you should use the SDK in the NXP official website.


Best Regards,

Zhenhua

From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-bounces@yoctoproject.org] On Behalf Of Thomas A. F. Thorne MEng AUS MIET
Sent: Thursday, July 14, 2016 12:34 AM
To: meta-freescale@yoctoproject.org
Subject: [meta-freescale] Which is the correct BSP to use for a freescale LS1021A-IOT development kit?

Good afternoon,

I have a freescale LS1021A-IOT development board and was wondering if the meta-fsl-arm layer was the correct board support package for it?  I can see the ls1021atwr.conf in  meta-fsl-arm/conf/machine/ which targets the ls102xa chipset so it seems likely to be the correct one.

What makes me wonder if it the correct one is that there is a dedicated ls1021aiot.conf in the meta-fsl-arm layer provided by the LS1021A-IOT SDK found at http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-arm-processors/qoriq-ls1021a-iot-gateway-reference-design:LS1021A-IoT?fpsp=1&tab=Design_Tools_Tab

Regards, Tom


--

Thomas Thorne  Software Engineer  Net2Edge Limited

[-- Attachment #2: Type: text/html, Size: 5614 bytes --]

Re: Which is the correct BSP to use for a freescale LS1021A-IOT development kit?

[Thomas A. F. Thorne MEng AUS MIET]

[-- Attachment #1.1.1: Type: text/plain, Size: 1723 bytes --]

Hello Zhenhua,

Thank you for confirming that.  I will stick to using the code supplied
in the SDK which seems to contain Yocto 1.6.1 daisy.  I'll make sure to
reference documents relating to that version 1.6 Yocto and the
corresponding Poky 11.0 version. 

Thomas Thorne  Software Engineer  Net2Edge Limited

On 14/07/16 12:43, Zhenhua Luo wrote:
>
> Hello Tom,
>
>  
>
> The meta-fsl-arm layer in Yocto git repo only supports ls1021atwr. To
> support ls1021a-iot board, you should use the SDK in the NXP official
> website.
>
>  
>
>  
>
> Best Regards,
>
>  
>
> Zhenhua
>
>  
>
> *From:*meta-freescale-bounces@yoctoproject.org
> [mailto:meta-freescale-bounces@yoctoproject.org] *On Behalf Of *Thomas
> A. F. Thorne MEng AUS MIET
> *Sent:* Thursday, July 14, 2016 12:34 AM
> *To:* meta-freescale@yoctoproject.org
> *Subject:* [meta-freescale] Which is the correct BSP to use for a
> freescale LS1021A-IOT development kit?
>
>  
>
> Good afternoon,
>
> I have a freescale LS1021A-IOT development board and was wondering if
> the meta-fsl-arm layer was the correct board support package for it? 
> I can see the ls1021atwr.conf in  meta-fsl-arm/conf/machine/ which
> targets the ls102xa chipset so it seems likely to be the correct one. 
>
> What makes me wonder if it the correct one is that there is a
> dedicated ls1021aiot.conf in the meta-fsl-arm layer provided by the
> LS1021A-IOT SDK found at
> http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-arm-processors/qoriq-ls1021a-iot-gateway-reference-design:LS1021A-IoT?fpsp=1&tab=Design_Tools_Tab
>
>
> Regards, Tom
>
> -- 
> Thomas Thorne  Software Engineer  Net2Edge Limited


[-- Attachment #1.1.2: Type: text/html, Size: 7067 bytes --]

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 484 bytes --]