[U-Boot] u-boot: x86: interrupt mapping

[Jian Luo <Jian.Luo4@boschrexroth.de>]

Hi Christian,

I took some time to recall what I did by patching FSP:

- search in every PE32 and TE image section for binary sequence
81c9000100008908c6460e01
and change to
81c9000102008908c6460e00

- then replace them in-place

The difference can be better understand if disassemblies are compared, eg:
  Disassembly of section .data:
@@ -3367,9 +3367,9 @@
      25fc:    05 00 05 00 00           add    $0x500,%eax
      2601:    8b 08                    mov    (%eax),%ecx
      2603:    81 e1 ff ff f8 ff        and    $0xfff8ffff,%ecx
-    2609:    81 c9 00 01 00 00        or     $0x100,%ecx
+    2609:    81 c9 00 01 02 00        or     $0x20100,%ecx
What I did here is setting BAUDSEL to SYS_25MHz.

      260f:    89 08                    mov    %ecx,(%eax)
-    2611:    c6 46 0e 01              movb   $0x1,0xe(%esi)
+    2611:    c6 46 0e 00              movb   $0x0,0xe(%esi)
Can't recall why I did this, maybe bypassing PLL altogether?

      2615:    c6 46 0f 00              movb   $0x0,0xf(%esi)
      2619:    c6 46 03 83              movb   $0x83,0x3(%esi)
      261d:    c6 46 01 00              movb   $0x0,0x1(%esi)

Since I don't rely on Topcliff UART for output, the baud rate 
recalculation is all skipped.

Best regards,

*Jian Luo
DC-IA/EAH2*

Tel.  +49(9352)18-4266

*Be**QIK
*

On 19.07.2016 17:21, Christian Gmeiner wrote:
> Hi Jian,
>
>> For the moment I have no answer to this question. I need to dive into
>> the vxworks code, which
>> is not what I like to do now (but needs to be done)-
>>
>> Yes, please do track it down. The interrupt line register configured
>> by U-Boot should be enough for VxWorks to function under PIC mode.
>>
>> I have an other (wired) question you may could help out.
>>
>> http://www.mouser.com/pdfdocs/Intel_Platform_Controller_Hub_EG20T_datasheet.pdf
>> (page 124)
>>
>> On my development board the uart_clk is connected to a oscillator and
>> everything works as expected.
>> But on the production devices the uart_clk is not connected and fsp
>> hangs with post code 0x2e.
>>
>> I am not sure about the meaning of post code 0x2e. Jian has some
>> working experience on Atom E6xx with U-Boot. Adding him.
>>
>> 0x2e == POST_PRE_MRC (arch/x86/include/asm/post.h)
>>
>> Now I would like to change the initial mux settings to use usb_48mhz
>> but I am quite sure that I need
>> to have the pci bus and its devices initialised already in order to
>> change the CLKCFG register. Do you
>> think there is an other way of accessing this register like fixed
>> memory address etc?
>>
>> Which register do you want to program for this uart_clk? If it's on
>> the PCI configuration space, you can use PCI config APIs to program.
>>
>> There a handful of registers I would need to program but all of them are
>> accessible via pic config space. E.g CLKCFG:
>>
>> Size: 32-bit Default: 20000C00 Power Well: Core
>> Access PCI Configuration B:D:F D0:F0 Offset Start: Offset End: 500h 503h
>>              Memory Mapped I/O BAR: PKTHubCTLBASE Offset: 500h
>>
>>
>> As I need to program those registers before fsp_init I must setup the pci
>> bus by myself, change the register values and call fsb_init routine.
>> Correct?
>>
>> My board had this problem too. I however toke a different approach
>> by patching the original FSP. The waiting for Topcliff UART ready is
>> completely
>> bypassed in all UEFI blobs. You can use UEFITool [1] to extract blobs in
>> the attached FSP for comparison.
>>
> Sooo... I did use the UEFITool to compare your fsp with mine and yeah...
> some files are different.
>
> File_Raw_06A70056_3D0F_4A94_A743_5491CC9391D3_body.bin
> Section_PE32_image_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_body.bin
> Section_PE32_image_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_header.bin
> Section_PE32_image_4D1F48D8_0498_4C09_8EDE_72F30B58B1F2_MpInit_body.bin
> Section_PE32_image_74D3B506_EE9C_47ED_B749_41261401DA78_TCInitDxe_body.bin
> Section_TE_image_1BA0062E_C779_4582_8566_336AE8F78F09_Volume_Top_File_body.bin
> Section_TE_image_52C05B14_0B98_496C_BC3B_04B50211D680_PeiCore_body.bin
> Section_TE_image_86D70125_BAA3_4296_A62F_602BEBBB9081_DxeIpl_body.bin
> Section_TE_image_9618C0DC_50A4_496C_994F_7241F282ED01_PlatformEarlyInit_body.bin
> Section_TE_image_9B3ADA4F_AE56_4C24_8DEA_F03B7558AE50_PcdPeim_body.bin
> Section_TE_image_D2C69B26_82E1_4A1B_AD35_ED0261B9F347_MemoryInitPei_body.bin
> File_PEI_module_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_info.txt
> File_PEI_module_4D1F48D8_0498_4C09_8EDE_72F30B58B1F2_MpInit_info.txt
> File_PEI_module_74D3B506_EE9C_47ED_B749_41261401DA78_TCInitDxe_info.txt
> Section_Compressed_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_info.txt
> Section_Compressed_4D1F48D8_0498_4C09_8EDE_72F30B58B1F2_MpInit_info.txt
> Section_Compressed_74D3B506_EE9C_47ED_B749_41261401DA78_TCInitDxe_info.txt
> Section_PE32_image_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_info.txt
> Section_PEI_dependency_47EA2673_2533_4C07_AABA_69CE5A7C5D35_PlatformLateInit_info.txt
> Section_PEI_dependency_4D1F48D8_0498_4C09_8EDE_72F30B58B1F2_MpInit_info.txt
>
> Any hint at what to look for? Sadly I am not an UEFI guy.
>
> greets
> --
> Christian Gmeiner, MSc
>
> https://soundcloud.com/christian-gmeiner