From: johnzeng <johnzeng2013@yahoo.com>
To: Sven Eckelmann <sven@narfation.org>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Subject: Re: Whether Batman-adv need suitable wifi network card (support interface modes ( mesh point ) ) .
Date: Wed, 26 Oct 2016 15:19:02 +0800 [thread overview]
Message-ID: <581058E6.4080706@yahoo.com> (raw)
In-Reply-To: <4752844.Su7blveJaV@bentobox>
Hello Sven:
HostB wlan0 : mac addr : ether 00:1d:43:10:15:44
HostA wlan0 : mac addr: ether c8:3a:35:c9:ce:71
i run the command at Host A ( Rt2070 ) at ( ping HostA from HostB)
iw dev wlan0 station dump:
Station 00:1d:43:10:15:44 (on wlan0)
inactive time: 140 ms
rx bytes: 4977553
rx packets: 126014
tx bytes: 0
tx packets: 0
tx retries: 0
tx failed: 0
rx drop misc: 0
signal: -39 dBm
signal avg: -39 dBm
tx bitrate: 1.0 MBit/s
rx bitrate: 1.0 MBit/s
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: no
MFP: no
TDLS peer: no
DTIM period: 0
beacon interval:100
connected time: 10084 seconds
[root@alarmpi ~]# tcpdump -i bat0
07:01:40.635517 ARP, Reply 0.0.0.0 is-at 43:05:43:05:00:00 (oui
Unknown), length 28
07:01:50.655521 ARP, Reply 0.0.0.0 is-at 43:05:43:05:00:00 (oui
Unknown), length 28
[root@alarmpi ~]# tcpdump -i wlan0
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on wlan0, link-type EN10MB (Ethernet), capture size 262144 bytes
07:02:35.815528 c8:3a:35:c9:ce:71 (oui Unknown) > Broadcast, ethertype
Unknown (0x4305), length 66:
0x0000: 000f 3202 d7e6 278c c83a 35c9 ce71 c83a ..2...'..:5..q.:
0x0010: 35c9 ce71 00ff 001c 0401 000c 0104 0001 5..q............
0x0020: 48b5 3b30 0000 0000 0601 0004 0000 0000 H.;0............
0x0030: 0201 0000
and i ping ip address belong to hostB (wlan0 )from HostA and it will be
fine .
batctl o No batman nodes in range
-----------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------
and i run same command at Host B ( RTL8188CUS ) at ( ping HostB from HostA)
iw dev wlan0 station dump:
" is blank "
[root@alarmpi ~]# tcpdump -i bat0
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on bat0, link-type EN10MB (Ethernet), capture size 262144 bytes
06:55:51.505401 ARP, Request who-has bogon tell bogon, length 28
06:55:51.506177 ARP, Reply bogon is-at a6:b8:8a:11:be:a2 (oui Unknown),
length 28
tcpdump -i wlan0
06:57:11.425351 c8:3a:35:c9:ce:71 (oui Unknown) > Broadcast, ethertype
Unknown (0x4305), length 66:
0x0000: 000f 3202 d7e6 2649 c83a 35c9 ce71 c83a ..2...&I.:5..q.:
0x0010: 35c9 ce71 00ff 001c 0401 000c 0104 0001 5..q............
0x0020: 48b5 3b30 0000 0000 0601 0004 0000 0000 H.;0............
0x0030: 0201 0000 ....
06:57:11.534759 00:1d:43:10:15:44 (oui Unknown) > Broadcast, ethertype
Unknown (0x4305), length 66:
0x0000: 000f 3105 d7e6 2649 c83a 35c9 ce71 c83a ..1...&I.:5..q.:
0x0010: 35c9 ce71 0000 001c 0401 000c 0104 0001 5..q............
0x0020: 48b5 3b30 0000 0000 0601 0004 0000 0000 H.;0............
0x0030: 0201 0000
and i ping ip address belong to hostA wlan0 from HostB and it will be fine .
batctl o No batman nodes in range
------------------------------------------------------------------------------------------------------------
And i thought Rt2070 support Broadcast and RTL8188CUS don't support
Broadcast or send ...
because when i ping ip (RTL8188CUS) from Rt2070 , and i can see ping
packet via (tcpdump -i bat0 ) and i can see Rt2070 mac addr via (tcpdump
-i wlan0 ) at HOSTB,
but i ping ip (Rt2070) from RTL8188CUS and i can't see any ping packet
from RTL8188CUS and i can't see RTL8188CUS mac via (tcpdump -i wlan0 )
at HOSTA
Whether it will be master reason ?
Thanks
...
于 2016年10月26日 14:07, Sven Eckelmann 写道:
> iw dev wlan0 station dump
next prev parent reply other threads:[~2016-10-26 7:19 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-25 9:25 Whether Batman-adv need suitable wifi network card (support interface modes ( mesh point ) ) johnzeng
2016-10-25 9:45 ` [B.A.T.M.A.N.] " Sven Eckelmann
2016-10-25 23:19 ` johnzeng
[not found] ` <580FFD64.7020704@yahoo.com>
2016-10-26 6:07 ` [B.A.T.M.A.N.] " Sven Eckelmann
2016-10-26 7:19 ` johnzeng [this message]
2016-10-26 8:17 ` Sven Eckelmann
2016-10-26 12:52 ` johnzeng
2016-10-26 13:05 ` [B.A.T.M.A.N.] " Sven Eckelmann
2016-10-26 13:42 ` johnzeng
2016-10-26 14:58 ` Martin Hundebøll
[not found] ` <mailman.170.1477486357.610.b.a.t.m.a.n@lists.open-mesh.org>
2016-10-26 15:09 ` [B.A.T.M.A.N.] " Simon Wunderlich
2016-10-26 7:00 ` Sven Eckelmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=581058E6.4080706@yahoo.com \
--to=johnzeng2013@yahoo.com \
--cc=b.a.t.m.a.n@lists.open-mesh.org \
--cc=sven@narfation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.