From: Alexander Stein <alexander.stein@ew.tq-group.com>
To: Frank Li <Frank.Li@nxp.com>
Cc: jun.li@nxp.com, frank.li@nxp.com, a-govindraju@ti.com,
gregkh@linuxfoundation.org, hzpeterchen@gmail.com,
imx@lists.linux.dev, linux-kernel@vger.kernel.org,
linux-usb@vger.kernel.org, pawell@cadence.com,
peter.chen@kernel.org, rogerq@kernel.org, stable@kernel.org
Subject: Re: [PATCH v2 1/1] usb: cdns3: host: fix endless superspeed hub port reset
Date: Thu, 27 Oct 2022 09:06:22 +0200 [thread overview]
Message-ID: <5877757.lOV4Wx5bFT@steina-w> (raw)
In-Reply-To: <20221026190749.2280367-1-Frank.Li@nxp.com>
Am Mittwoch, 26. Oktober 2022, 21:07:49 CEST schrieb Frank Li:
> From: Li Jun <jun.li@nxp.com>
>
> When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device,
> some usb hub reports endless port reset message.
>
> [ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd
> [ 190.352834] hub 2-1:1.0: USB hub found
> [ 190.356995] hub 2-1:1.0: 4 ports detected
> [ 190.700056] usb 2-1: USB disconnect, device number 88
> [ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd
> [ 192.500820] hub 2-1:1.0: USB hub found
> [ 192.504977] hub 2-1:1.0: 4 ports detected
> [ 192.852066] usb 2-1: USB disconnect, device number 89
>
> The reason is the runtime pm state of USB2.0 port is active and
> USB 3.0 port is suspend, so parent device is active state.
>
> cat
> /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/po
> wer/runtime_status
>
> suspended
>
> cat
> /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/po
> wer/runtime_status
>
> active
>
> cat
> /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/r
> untime_status
>
> active
>
> cat
> /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status
>
> active
>
> So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied.
>
> move U3 configure into host start. Reinit again in resume function in case
> controller power lost during suspend.
>
> Cc: stable@vger.kernel.org 5.10
> Signed-off-by: Li Jun <jun.li@nxp.com>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
>
> Change from V1 to V2.
> - call xhci_cdns3_plat_start() in xhci_cdns3_resume_quirk
> in case power lost during suspend
>
> drivers/usb/cdns3/host.c | 56 ++++++++++++++++++++--------------------
> 1 file changed, 28 insertions(+), 28 deletions(-)
>
> diff --git a/drivers/usb/cdns3/host.c b/drivers/usb/cdns3/host.c
> index 9643b905e2d8..6164fc4c96a4 100644
> --- a/drivers/usb/cdns3/host.c
> +++ b/drivers/usb/cdns3/host.c
> @@ -24,11 +24,37 @@
> #define CFG_RXDET_P3_EN BIT(15)
> #define LPM_2_STB_SWITCH_EN BIT(25)
>
> -static int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd);
> +static void xhci_cdns3_plat_start(struct usb_hcd *hcd)
> +{
> + struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> + u32 value;
> +
> + /* set usbcmd.EU3S */
> + value = readl(&xhci->op_regs->command);
> + value |= CMD_PM_INDEX;
> + writel(value, &xhci->op_regs->command);
> +
> + if (hcd->regs) {
> + value = readl(hcd->regs + XECP_AUX_CTRL_REG1);
> + value |= CFG_RXDET_P3_EN;
> + writel(value, hcd->regs + XECP_AUX_CTRL_REG1);
> +
> + value = readl(hcd->regs + XECP_PORT_CAP_REG);
> + value |= LPM_2_STB_SWITCH_EN;
> + writel(value, hcd->regs + XECP_PORT_CAP_REG);
> + }
> +}
> +
> +static int xhci_cdns3_resume_quirk(struct usb_hcd *hcd)
> +{
> + xhci_cdns3_plat_start(hcd);
> + return 0;
> +}
>
> static const struct xhci_plat_priv xhci_plat_cdns3_xhci = {
> .quirks = XHCI_SKIP_PHY_INIT | XHCI_AVOID_BEI,
> - .suspend_quirk = xhci_cdns3_suspend_quirk,
> + .plat_start = xhci_cdns3_plat_start,
> + .resume_quirk = xhci_cdns3_resume_quirk,
> };
>
> static int __cdns_host_init(struct cdns *cdns)
> @@ -90,32 +116,6 @@ static int __cdns_host_init(struct cdns *cdns)
> return ret;
> }
>
> -static int xhci_cdns3_suspend_quirk(struct usb_hcd *hcd)
> -{
> - struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> - u32 value;
> -
> - if (pm_runtime_status_suspended(hcd->self.controller))
> - return 0;
> -
> - /* set usbcmd.EU3S */
> - value = readl(&xhci->op_regs->command);
> - value |= CMD_PM_INDEX;
> - writel(value, &xhci->op_regs->command);
> -
> - if (hcd->regs) {
> - value = readl(hcd->regs + XECP_AUX_CTRL_REG1);
> - value |= CFG_RXDET_P3_EN;
> - writel(value, hcd->regs + XECP_AUX_CTRL_REG1);
> -
> - value = readl(hcd->regs + XECP_PORT_CAP_REG);
> - value |= LPM_2_STB_SWITCH_EN;
> - writel(value, hcd->regs + XECP_PORT_CAP_REG);
> - }
> -
> - return 0;
> -}
> -
> static void cdns_host_exit(struct cdns *cdns)
> {
> kfree(cdns->xhci_plat_data);
Although I could only test it on v5.15 downstream kernel
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
next prev parent reply other threads:[~2022-10-27 7:07 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-26 19:07 [PATCH v2 1/1] usb: cdns3: host: fix endless superspeed hub port reset Frank Li
2022-10-27 5:51 ` Peter Chen
2022-10-27 7:06 ` Alexander Stein [this message]
2022-11-03 15:29 ` [EXT] " Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5877757.lOV4Wx5bFT@steina-w \
--to=alexander.stein@ew.tq-group.com \
--cc=Frank.Li@nxp.com \
--cc=a-govindraju@ti.com \
--cc=gregkh@linuxfoundation.org \
--cc=hzpeterchen@gmail.com \
--cc=imx@lists.linux.dev \
--cc=jun.li@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=pawell@cadence.com \
--cc=peter.chen@kernel.org \
--cc=rogerq@kernel.org \
--cc=stable@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.