Re: Promise sx6000

[Linux Lists <user_linux@citma.cu>]

Hi :

I have followed your advises and finally , it seem to be ok with my 
promise sx6000 card.
I have installed Red Hat 8 with 2.4.18-14 ,i2o support as module, but i 
can not find my card anywhere.

Here  i am sending you my dmesg and my modules.conf .
Notes I have a  120GB in hda where i have installed red hat , and 5 
hardrives in the promise card .
.............
.........

VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
PDC20276: IDE controller on PCI bus 02 dev 00
PDC20276: chipset revision 1
ide: Found promise 20265 in RAID mode.
PDC20276: not 100% native mode: will probe irqs later
PDC20276: simplex device:  DMA disabled
ide2: PDC20276 Bus-Master DMA disabled (BIOS)
PDC20276: simplex device:  DMA disabled
ide3: PDC20276 Bus-Master DMA disabled (BIOS)
PDC20276: IDE controller on PCI bus 02 dev 08
PDC20276: chipset revision 1
ide: Found promise 20265 in RAID mode.
PDC20276: not 100% native mode: will probe irqs later
PDC20276: simplex device:  DMA disabled
ide4: PDC20276 Bus-Master DMA disabled (BIOS)
PDC20276: simplex device:  DMA disabled
ide5: PDC20276 Bus-Master DMA disabled (BIOS)
PDC20276: IDE controller on PCI bus 02 dev 10
PDC20276: chipset revision 1
ide: Found promise 20265 in RAID mode.
PDC20276: not 100% native mode: will probe irqs later
PDC20276: simplex device:  DMA disabled
ide6: PDC20276 Bus-Master DMA disabled (BIOS)
PDC20276: simplex device:  DMA disabled
ide7: PDC20276 Bus-Master DMA disabled (BIOS)
hda: WDC WD1200JB-75CRA0, ATA DISK drive
hdb: no response (status = 0xa1), resetting drive
hdb: no response (status = 0xa1)
hdc: AOPEN 16XDVD-ROM/AMH 20020328, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: setmax LBA 234441648, native  234375000
hda: 234375000 sectors (120000 MB) w/8192KiB Cache, CHS=14589/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 220k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 17
I2O Block Storage OSM v0.9
   (c) Copyright 1999-2001 Red Hat Software.
i2o_block: registered device at major 80
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
Journalled Block Device driver loaded

Why is not my RAID under /dev/i2o/hda ?

David