Hi,

I have a MPC8347 based embedded PC running Linux 2.6.27.
I am trying to access a NAND device connected to the LBC and UPM.
The Ready/Busy* pin of the NAND device is connected to the built in GPIO-1 on pin 4 (input).

When I try to access the NAND device, the function of_get_gpio() from drivers/of/gpio.c gets called, and
it reports that my GPIO is not registered. Here are the actual debug messages:

LK_DEBUG: gpio.c : of_get_gpio : name=upm type=<NULL> index=0
LK_DEBUG: gpio.c : of_get_gpio : got property
LK_DEBUG: gpio.c : of_get_gpio : nr_cell=3
LK_DEBUG: gpio.c : of_get_gpio : gc.name=gpio-controller gc.type=<NULL> gc->Data=0x0
LK_DEBUG: gpio.c : of_get_gpio : /localbus/upm@1,0: gpio controller /soc8349@e0000000/gpio-controller@e0000c00: is not registered

When I check in /proc/device-tree/soc8349@e0000000/, I find that entries are present for both GPIOs are present.

Here are debug registration messages, indicating that gpio registered successfully:

##### LK_DEBUG: of_plat_dev_create : NAME=soc8349
##### LK_DEBUG: of_plat_dev_create : NAME=wdt
##### LK_DEBUG: of_plat_dev_create : NAME=i2c
##### LK_DEBUG: of_plat_dev_create : NAME=i2c
##### LK_DEBUG: of_plat_dev_create : NAME=spi
##### LK_DEBUG: of_plat_dev_create : NAME=dma
##### LK_DEBUG: of_plat_dev_create : NAME=usb
##### LK_DEBUG: of_plat_dev_create : NAME=usb
##### LK_DEBUG: of_plat_dev_create : NAME=mdio
##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
##### LK_DEBUG: of_plat_dev_create : NAME=ethernet
##### LK_DEBUG: of_plat_dev_create : NAME=serial
##### LK_DEBUG: of_plat_dev_create : NAME=serial
##### LK_DEBUG: of_plat_dev_create : NAME=crypto
##### LK_DEBUG: of_plat_dev_create : NAME=pic
##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
##### LK_DEBUG: of_plat_dev_create : NAME=gpio-controller
##### LK_DEBUG: of_plat_dev_create : NAME=localbus
##### LK_DEBUG: of_plat_dev_create : NAME=upm

Most probably something is wrong in my device tree (listed below). Can someone please point me in the right direction?

thanks a lot for your help.
LK

-------------------------------------------------------------

/*
* MPC8349E MDS Device Tree Source
*
* Copyright 2005, 2006 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/

/dts-v1/;

/ {
        model = "MPC8349EMDS";
        compatible = "MPC8349EMDS", "MPC834xMDS", "MPC83xxMDS";
        #address-cells = <1>;
        #size-cells = <1>;

        aliases {
                ethernet0 = &enet0;
                ethernet1 = &enet1;
                serial0 = &serial0;
                serial1 = &serial1;
                pci0 = &pci0;
                pci1 = &pci1;
        };

        cpus {
                #address-cells = <1>;
                #size-cells = <0>;

                PowerPC,8349@0 {
                        device_type = "cpu";
                        reg = <0x0>;
                        d-cache-line-size = <32>;
                        i-cache-line-size = <32>;
                        d-cache-size = <32768>;
                        i-cache-size = <32768>;
                        timebase-frequency = <0>;       // from bootloader
                        bus-frequency = <0>;            // from bootloader
                        clock-frequency = <0>;          // from bootloader
                };
        };

        memory {
                device_type = "memory";
                reg = <0x00000000 0x10000000>; // 256MB at 0
        };

        bcsr@e2400000 {
                device_type = "board-control";
                reg = <0xe2400000 0x8000>;
        };

        soc8349@e0000000 {
                #address-cells = <1>;
                #size-cells = <1>;
                device_type = "soc";
                compatible = "simple-bus";
                ranges = <0x0 0xe0000000 0x00100000>;
                reg = <0xe0000000 0x00000200>;
                bus-frequency = <0>;

                wdt@200 {
                        device_type = "watchdog";
                        compatible = "mpc83xx_wdt";
                        reg = <0x200 0x100>;
                };

                i2c@3000 {
                        #address-cells = <1>;
                        #size-cells = <0>;
                        cell-index = <0>;
                        compatible = "fsl-i2c";
                        reg = <0x3000 0x100>;
                        interrupts = <14 0x8>;
                        interrupt-parent = <&ipic>;
                        dfsrr;

                        rtc@68 {
                                compatible = "dallas,ds1374";
                                reg = <0x68>;
                        };
                };

                i2c@3100 {
                        #address-cells = <1>;
                        #size-cells = <0>;
                        cell-index = <1>;
                        compatible = "fsl-i2c";
                        reg = <0x3100 0x100>;
                        interrupts = <15 0x8>;
                        interrupt-parent = <&ipic>;
                        dfsrr;
                };

                spi@7000 {
                        cell-index = <0>;
                        compatible = "fsl,spi";
                        reg = <0x7000 0x1000>;
                        interrupts = <16 0x8>;
                        interrupt-parent = <&ipic>;
                        mode = "cpu";
                };

                dma@82a8 {
                        #address-cells = <1>;
                        #size-cells = <1>;
                        compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
                        reg = <0x82a8 4>;
                        ranges = <0 0x8100 0x1a8>;
                        interrupt-parent = <&ipic>;
                        interrupts = <71 8>;
                        cell-index = <0>;
                        dma-channel@0 {
                                compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
                                reg = <0 0x80>;
                                interrupt-parent = <&ipic>;
                                interrupts = <71 8>;
                        };
                        dma-channel@80 {
                                compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
                                reg = <0x80 0x80>;
                                interrupt-parent = <&ipic>;
                                interrupts = <71 8>;
                        };
                        dma-channel@100 {
                                compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
                                reg = <0x100 0x80>;
                                interrupt-parent = <&ipic>;
                                interrupts = <71 8>;
                        };
                        dma-channel@180 {
                                compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
                                reg = <0x180 0x28>;
                                interrupt-parent = <&ipic>;
                                interrupts = <71 8>;
                        };
                };

                /* phy type (ULPI or SERIAL) are only types supported for MPH */
                /* port = 0 or 1 */
                usb@22000 {
                        compatible = "fsl-usb2-mph";
                        reg = <0x22000 0x1000>;
                        #address-cells = <1>;
                        #size-cells = <0>;
                        interrupt-parent = <&ipic>;
                        interrupts = <39 0x8>;
                        phy_type = "ulpi";
                        port1;
                };
                /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
                usb@23000 {
                        compatible = "fsl-usb2-dr";
                        reg = <0x23000 0x1000>;
                        #address-cells = <1>;
                        #size-cells = <0>;
                        interrupt-parent = <&ipic>;
                        interrupts = <38 0x8>;
                        dr_mode = "otg";
                        phy_type = "ulpi";
                };

                mdio@24520 {
                        #address-cells = <1>;
                        #size-cells = <0>;
                        compatible = "fsl,gianfar-mdio";
                        reg = <0x24520 0x20>;

                        phy0: ethernet-phy@0 {
                                interrupt-parent = <&ipic>;
                                interrupts = <17 0x8>;
                                reg = <0x1>;
                                device_type = "ethernet-phy";
                        };
                        phy1: ethernet-phy@1 {
                                interrupt-parent = <&ipic>;
                                interrupts = <18 0x8>;
                                reg = <0x2>;
                                device_type = "ethernet-phy";
                        };
                };

                enet0: ethernet@24000 {
                        cell-index = <0>;
                        device_type = "network";
                        model = "TSEC";
                        compatible = "gianfar";
                        reg = <0x24000 0x1000>;
                        local-mac-address = [ 00 00 00 00 00 00 ];
                        interrupts = <32 0x8 33 0x8 34 0x8>;
                        interrupt-parent = <&ipic>;
                        phy-handle = <&phy0>;
                        linux,network-index = <0>;
                };

                enet1: ethernet@25000 {
                        cell-index = <1>;
                        device_type = "network";
                        model = "TSEC";
                        compatible = "gianfar";
                        reg = <0x25000 0x1000>;
                        local-mac-address = [ 00 00 00 00 00 00 ];
                        interrupts = <35 0x8 36 0x8 37 0x8>;
                        interrupt-parent = <&ipic>;
                        phy-handle = <&phy1>;
                        linux,network-index = <1>;
                };

                serial0: serial@4500 {
                        cell-index = <0>;
                        device_type = "serial";
                        compatible = "ns16550";
                        reg = <0x4500 0x100>;
                        clock-frequency = <0>;
                        interrupts = <9 0x8>;
                        interrupt-parent = <&ipic>;
                };

                serial1: serial@4600 {
                        cell-index = <1>;
                        device_type = "serial";
                        compatible = "ns16550";
                        reg = <0x4600 0x100>;
                        clock-frequency = <0>;
                        interrupts = <10 0x8>;
                        interrupt-parent = <&ipic>;
                };

                crypto@30000 {
                        compatible = "fsl,sec2.0";
                        reg = <0x30000 0x10000>;
                        interrupts = <11 0x8>;
                        interrupt-parent = <&ipic>;
                        fsl,num-channels = <4>;
                        fsl,channel-fifo-len = <24>;
                        fsl,exec-units-mask = <0x7e>;
                        fsl,descriptor-types-mask = <0x01010ebf>;
                };

                /* IPIC
                 * interrupts cell = <intr #, sense>
                 * sense values match linux IORESOURCE_IRQ_* defines:
                 * sense == 8: Level, low assertion
                 * sense == 2: Edge, high-to-low change
                 */
                ipic: pic@700 {
                        interrupt-controller;
                        #address-cells = <0>;
                        #interrupt-cells = <2>;
                        reg = <0x700 0x100>;
                        device_type = "ipic";
                };

                gpio1: gpio-controller@e0000c00 {
                        #gpio-cells = <2>;
                        compatible = "fsl,mpc8349-gpio-bank";
                        reg = <0xe0000c00 0x100>;
                        gpio-controller;
                };

                gpio2: gpio-controller@e0000d00 {
                        #gpio-cells = <2>;
                        compatible = "fsl,mpc8349-gpio-bank";
                        reg = <0xe0000d00 0x100>;
                        gpio-controller;
                };
        };

        localbus {
                compatible = "fsl,pq3-localbus", "simple-bus";
                #address-cells = <2>;
                #size-cells = <1>;
                reg = <0xe0005000 0x100000>;       // BRx, ORx, etc.

                upm@1,0 {
                        #address-cells = <1>;
                        #size-cells = <1>;
                        compatible = "fsl,upm-nand";
                        reg = <3 0xa0000000 0x800>;
                        fsl,upm-addr-offset = <0x10>;
                        fsl,upm-cmd-offset = <0x08>;
                        gpios = <&gpio1 4 0>;

                        nand@0 {
                                #address-cells = <1>;
                                #size-cells = <1>;
                                compatible = "fsl,lbc-nand";

                                partition@0 {
                                        label = "EVERYTHING";
                                        reg = <0x00000000 0x01000000>;
                                };
                        };
                };
        };

        pci0: pci@e0008500 {
                cell-index = <1>;
                interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
                interrupt-map = <

                                /* IDSEL 0x11 */
                                 0x8800 0x0 0x0 0x1 &ipic 20 0x8
                                 0x8800 0x0 0x0 0x2 &ipic 21 0x8
                                 0x8800 0x0 0x0 0x3 &ipic 22 0x8
                                 0x8800 0x0 0x0 0x4 &ipic 23 0x8

                                /* IDSEL 0x12 */
                                 0x9000 0x0 0x0 0x1 &ipic 22 0x8
                                 0x9000 0x0 0x0 0x2 &ipic 23 0x8
                                 0x9000 0x0 0x0 0x3 &ipic 20 0x8
                                 0x9000 0x0 0x0 0x4 &ipic 21 0x8

                                /* IDSEL 0x13 */
                                 0x9800 0x0 0x0 0x1 &ipic 23 0x8
                                 0x9800 0x0 0x0 0x2 &ipic 20 0x8
                                 0x9800 0x0 0x0 0x3 &ipic 21 0x8
                                 0x9800 0x0 0x0 0x4 &ipic 22 0x8

                                /* IDSEL 0x15 */
                                 0xa800 0x0 0x0 0x1 &ipic 20 0x8
                                 0xa800 0x0 0x0 0x2 &ipic 21 0x8
                                 0xa800 0x0 0x0 0x3 &ipic 22 0x8
                                 0xa800 0x0 0x0 0x4 &ipic 23 0x8

                                /* IDSEL 0x16 */
                                 0xb000 0x0 0x0 0x1 &ipic 23 0x8
                                 0xb000 0x0 0x0 0x2 &ipic 20 0x8
                                 0xb000 0x0 0x0 0x3 &ipic 21 0x8
                                 0xb000 0x0 0x0 0x4 &ipic 22 0x8

                                /* IDSEL 0x17 */
                                 0xb800 0x0 0x0 0x1 &ipic 22 0x8
                                 0xb800 0x0 0x0 0x2 &ipic 23 0x8
                                 0xb800 0x0 0x0 0x3 &ipic 20 0x8
                                 0xb800 0x0 0x0 0x4 &ipic 21 0x8

                                /* IDSEL 0x18 */
                                 0xc000 0x0 0x0 0x1 &ipic 21 0x8
                                 0xc000 0x0 0x0 0x2 &ipic 22 0x8
                                 0xc000 0x0 0x0 0x3 &ipic 23 0x8
                                 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
                interrupt-parent = <&ipic>;
                interrupts = <66 0x8>;
                bus-range = <0 0>;
                ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
                          0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
                          0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
                clock-frequency = <66666666>;
                #interrupt-cells = <1>;
                #size-cells = <2>;
                #address-cells = <3>;
                reg = <0xe0008500 0x100>;
                compatible = "fsl,mpc8349-pci";
                device_type = "pci";
        };

        pci1: pci@e0008600 {
                cell-index = <2>;
                interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
                interrupt-map = <

                                /* IDSEL 0x11 */
                                 0x8800 0x0 0x0 0x1 &ipic 20 0x8
                                 0x8800 0x0 0x0 0x2 &ipic 21 0x8
                                 0x8800 0x0 0x0 0x3 &ipic 22 0x8
                                 0x8800 0x0 0x0 0x4 &ipic 23 0x8

                                /* IDSEL 0x12 */
                                 0x9000 0x0 0x0 0x1 &ipic 22 0x8
                                 0x9000 0x0 0x0 0x2 &ipic 23 0x8
                                 0x9000 0x0 0x0 0x3 &ipic 20 0x8
                                 0x9000 0x0 0x0 0x4 &ipic 21 0x8

                                /* IDSEL 0x13 */
                                 0x9800 0x0 0x0 0x1 &ipic 23 0x8
                                 0x9800 0x0 0x0 0x2 &ipic 20 0x8
                                 0x9800 0x0 0x0 0x3 &ipic 21 0x8
                                 0x9800 0x0 0x0 0x4 &ipic 22 0x8

                                /* IDSEL 0x15 */
                                 0xa800 0x0 0x0 0x1 &ipic 20 0x8
                                 0xa800 0x0 0x0 0x2 &ipic 21 0x8
                                 0xa800 0x0 0x0 0x3 &ipic 22 0x8
                                 0xa800 0x0 0x0 0x4 &ipic 23 0x8

                                /* IDSEL 0x16 */
                                 0xb000 0x0 0x0 0x1 &ipic 23 0x8
                                 0xb000 0x0 0x0 0x2 &ipic 20 0x8
                                 0xb000 0x0 0x0 0x3 &ipic 21 0x8
                                 0xb000 0x0 0x0 0x4 &ipic 22 0x8

                                /* IDSEL 0x17 */
                                 0xb800 0x0 0x0 0x1 &ipic 22 0x8
                                 0xb800 0x0 0x0 0x2 &ipic 23 0x8
                                 0xb800 0x0 0x0 0x3 &ipic 20 0x8
                                 0xb800 0x0 0x0 0x4 &ipic 21 0x8

                                /* IDSEL 0x18 */
                                 0xc000 0x0 0x0 0x1 &ipic 21 0x8
                                 0xc000 0x0 0x0 0x2 &ipic 22 0x8
                                 0xc000 0x0 0x0 0x3 &ipic 23 0x8
                                 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
                interrupt-parent = <&ipic>;
                interrupts = <67 0x8>;
                bus-range = <0 0>;
                ranges = <0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
                          0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
                          0x01000000 0x0 0x00000000 0xe2100000 0x0 0x00100000>;
                clock-frequency = <66666666>;
                #interrupt-cells = <1>;
                #size-cells = <2>;
                #address-cells = <3>;
                reg = <0xe0008600 0x100>;
                compatible = "fsl,mpc8349-pci";
                device_type = "pci";
        };

        chosen {
                linux,stdout-path = &serial0;
        };
};