Re: [PATCH v3 1/4] iio: add power and energy measurement modifiers

[David Lechner <dlechner@baylibre.com>]

On 8/8/25 9:10 AM, Antoniu Miclaus wrote:
> Add new IIO modifiers to support power and energy measurement devices:
> 
> Power modifiers:
> - IIO_MOD_ACTIVE: Real power consumed by the load
> - IIO_MOD_REACTIVE: Power that oscillates between source and load
> - IIO_MOD_APPARENT: Magnitude of complex power
> - IIO_MOD_FUND_REACTIVE: Reactive power at fundamental frequency
> - IIO_MOD_FACTOR: Power factor (ratio of active to apparent power)
> 
> Signal quality modifiers:
> - IIO_MOD_RMS: Root Mean Square value
> 
> These modifiers enable proper representation of power measurement
> devices like energy meters and power analyzers.
> 
> Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
> ---
> changes in v3:
>  - remove accumulated energy modifiers
>  - rename power_factor to powerfactor for consistency
>  Documentation/ABI/testing/sysfs-bus-iio | 11 +++++++++++
>  drivers/iio/industrialio-core.c         |  5 +++++
>  include/linux/iio/types.h               |  1 +
>  include/uapi/linux/iio/types.h          |  4 ++++
>  4 files changed, 21 insertions(+)
> 
> diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
> index 2fb2cea4b192..28f51e4cc367 100644
> --- a/Documentation/ABI/testing/sysfs-bus-iio
> +++ b/Documentation/ABI/testing/sysfs-bus-iio
> @@ -167,7 +167,12 @@ Description:
>  		is required is a consistent labeling.  Units after application
>  		of scale and offset are millivolts.
>  
> +What:		/sys/bus/iio/devices/iio:deviceX/in_altvoltageY_rms_raw

This looks out of place. There is no existing in_altvoltage_raw, so we need
to start a new section.

> +
>  What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_raw
> +What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_active_raw
> +What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_reactive_raw
> +What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_apparent_raw
>  KernelVersion:	4.5
>  Contact:	linux-iio@vger.kernel.org
>  Description:
> @@ -176,6 +181,8 @@ Description:
>  		unique to allow association with event codes. Units after
>  		application of scale and offset are milliwatts.
>  
> +What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_powerfactor

This one also needs a new section with Description: etc.

> +
>  What:		/sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw
>  KernelVersion:	3.2
>  Contact:	linux-iio@vger.kernel.org
> @@ -1569,6 +1576,9 @@ Description:
>  
>  What:		/sys/.../iio:deviceX/in_energy_input
>  What:		/sys/.../iio:deviceX/in_energy_raw
> +What:		/sys/.../iio:deviceX/in_energyY_active_raw
> +What:		/sys/.../iio:deviceX/in_energyY_reactive_raw
> +What:		/sys/.../iio:deviceX/in_energyY_apparent_raw
>  KernelVersion:	4.0
>  Contact:	linux-iio@vger.kernel.org
>  Description:
> @@ -1692,6 +1702,7 @@ Description:
>  
>  What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
>  What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
> +What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_rms_raw

Shouldn't this be in_altcurrentY_rms_raw? in_currentY_raw is DC current, not AC.
And we will likely need IIO_ALTCURRENT to go with it.

>  KernelVersion:	3.17
>  Contact:	linux-iio@vger.kernel.org
>  Description: