From: Angelo <s104259@yahoo.it>
To: Linuxppc-dev@ozlabs.org
Subject: Installation on a MPC5200 based custom board
Date: Fri, 5 Dec 2008 10:47:01 +0000 (GMT) [thread overview]
Message-ID: <688884.68610.qm@web23105.mail.ird.yahoo.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 4311 bytes --]
Hi all.
I saw that someones trying to work on a custom board based on mpc5200.
I have:
* u-boot 1.2.0
* kernel 2.6.21
* arch=powerpc
* custom dts based on lite5200b.dts
* USB port (USB2) configured on the Ethernet port
Is it necessary to combine Ethernet and usb nodes?
However this is the log when a usb-storage is plugged:
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0004
ppc-of-ohci f0001000.usb: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ppc-of-ohci f0001000.usb: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ppc-of-ohci and address 2
BUG: soft lockup detected on CPU#0!
Call Trace:
[C7E05A50] [C0007FD8] show_stack+0x3c/0x194 (unreliable)
[C7E05A80] [C004A380] softlockup_tick+0xa4/0xd4
[C7E05AA0] [C002B998] run_local_timers+0x18/0x28
[C7E05AB0] [C002B9D8] update_process_times+0x30/0x7c
[C7E05AC0] [C003FF3C] tick_sched_timer+0xb0/0x280
[C7E05B20] [C003C538] hrtimer_interrupt+0x214/0x26c
[C7E05B80] [C000E744] timer_interrupt+0x88/0x354
[C7E05BF0] [C0011C04] ret_from_except+0x0/0x14
--- Exception: 901 at handle_IRQ_event+0x7c/0x1e8
LR = handle_level_irq+0x90/0x13c
[C7E05CB0] [C7F15C00] 0xc7f15c00 (unreliable)
[C7E05CD0] [C004C2E0] handle_level_irq+0x90/0x13c
[C7E05CE0] [C0006304] do_IRQ+0x98/0xbc
[C7E05CF0] [C0011C04] ret_from_except+0x0/0x14
--- Exception: 501 at schedule+0x38/0x64c
LR = schedule_timeout+0x68/0xe4
[C7E05DB0] [C01A1650] usb_hcd_submit_urb+0x190/0x8a0 (unreliable)
[C7E05E00] [C02389A4] schedule_timeout+0x68/0xe4
[C7E05E40] [C0238378] wait_for_completion_timeout+0x8c/0x138
[C7E05E80] [C01A2B60] usb_start_wait_urb+0x64/0x124
[C7E05EB0] [C01A2E1C] usb_control_msg+0xc4/0xf0
[C7E05EF0] [C019D0D0] hub_port_init+0x424/0x614
[C7E05F40] [C019F42C] hub_thread+0x434/0xe64
[C7E05FC0] [C0037E60] kthread+0xc0/0xfc
[C7E05FF0] [C00123F8] original_kernel_thread+0x44/0x60
ppc-of-ohci f0001000.usb: OHCI Unrecoverable Error, disabled
ppc-of-ohci f0001000.usb: OHCI controller state
ppc-of-ohci f0001000.usb: OHCI 1.0, NO legacy support registers
ppc-of-ohci f0001000.usb: control 0x093 HCFS=operational CLE CBSR=3
ppc-of-ohci f0001000.usb: cmdstatus 0x00000 SOC=0
ppc-of-ohci f0001000.usb: intrstatus 0x00000074 RHSC FNO UE SF
ppc-of-ohci f0001000.usb: intrenable 0x8000001a MIE UE RD WDH
ppc-of-ohci f0001000.usb: ed_controlhead 07fcc000
ppc-of-ohci f0001000.usb: ed_controlcurrent fffffff0
ppc-of-ohci f0001000.usb: hcca frame #ddb6
ppc-of-ohci f0001000.usb: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
ppc-of-ohci f0001000.usb: roothub.b 00000000 PPCM=0000 DR=0000
ppc-of-ohci f0001000.usb: roothub.status 00008000 DRWE
ppc-of-ohci f0001000.usb: roothub.portstatus [0] 0x00000100 PPS
ppc-of-ohci f0001000.usb: roothub.portstatus [1] 0x00030100 PESC CSC PPS
ppc-of-ohci f0001000.usb: HC died; cleaning up
irq 134: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[C046FDF0] [C0007FD8] show_stack+0x3c/0x194 (unreliable)
[C046FE20] [C004B358] __report_bad_irq+0x34/0xac
[C046FE40] [C004B4AC] note_interrupt+0xdc/0x288
[C046FE70] [C004C344] handle_level_irq+0xf4/0x13c
[C046FE80] [C0006304] do_IRQ+0x98/0xbc
[C046FE90] [C0011C04] ret_from_except+0x0/0x14
--- Exception: 501 at schedule+0x304/0x64c
LR = schedule+0x2d8/0x64c
[C046FFA0] [C004A2B4] watchdog+0x4c/0x74
[C046FFC0] [C0037E60] kthread+0xc0/0xfc
[C046FFF0] [C00123F8] original_kernel_thread+0x44/0x60
handlers:
[<c01a1008>] (usb_hcd_irq+0x0/0x9c)
Disabling IRQ #134
usb 1-2: khubd timed out on ep0in len=0/64
hub 1-0:1.0: cannot reset port 2 (err = -19)
hub 1-0:1.0: cannot disable port 2 (err = -19)
ppc-of-ohci f0001000.usb: leak ed c7fcc000 (#00) state 0 (has tds)
hub 1-0:1.0: cannot reset port 2 (err = -19)
hub 1-0:1.0: cannot disable port 2 (err = -19)
hub 1-0:1.0: cannot reset port 2 (err = -19)
hub 1-0:1.0: cannot disable port 2 (err = -19)
hub 1-0:1.0: cannot reset port 2 (err = -19)
hub 1-0:1.0: cannot disable port 2 (err = -19)
hub 1-0:1.0: cannot disable port 2 (err = -19)
hub 1-0:1.0: state 0 ports 2 chg 0000 evt 0004
Please mail me any idea...
Thanks,
@ngel
[-- Attachment #2: Type: text/html, Size: 4672 bytes --]
next reply other threads:[~2008-12-05 10:47 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-05 10:47 Angelo [this message]
2008-12-05 12:20 ` Installation on a MPC5200 based custom board Gary Thomas
2008-12-05 13:00 ` R: " gianfranco.casanova
2008-12-05 17:36 ` Juergen Beisert
2008-12-05 19:33 ` Jon Smirl
2008-12-05 20:29 ` Angelo
-- strict thread matches above, loose matches on Subject: below --
2008-07-11 22:07 Sylvain Lamontagne
2008-07-11 22:12 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=688884.68610.qm@web23105.mail.ird.yahoo.com \
--to=s104259@yahoo.it \
--cc=Linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.