From: Chris Rankin <rankincj@yahoo.com>
To: Andrew Morton <akpm@linux-foundation.org>
Cc: lenb@kernel.org, rankincj@yahoo.com,
linux-kernel@vger.kernel.org, mingo@elte.hu, tglx@linutronix.de,
linux-acpi@vger.kernel.org
Subject: Re: [BUG] 2.6.24 refuses to boot - NMI watchdog problem?
Date: Fri, 8 Feb 2008 23:22:55 +0000 (GMT) [thread overview]
Message-ID: <7606.9306.qm@web52905.mail.re2.yahoo.com> (raw)
In-Reply-To: <20080207122652.02a7d5d5.akpm@linux-foundation.org>
And the same thing with 2.6.24.1.
Cheers,
Chris
Linux version 2.6.24.1 (chris@twopit.underworld) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33))
#1 SMP PREEMPT Fri Feb 8 22:41:10 GMT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffeb000 (usable)
BIOS-e820: 000000001ffeb000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131051
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131051
DMI 2.3 present.
ACPI: RSDP 000F7B40, 0014 (r0 ASUS )
ACPI: RSDT 1FFEB000, 0030 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: FACP 1FFEB100, 0074 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: DSDT 1FFEB180, 39FA (r1 ASUS TUSL2-C 1000 MSFT 100000B)
ACPI: FACS 1FFFF000, 0040
ACPI: BOOT 1FFEB040, 0028 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: APIC 1FFEB080, 005A (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: PM-Timer IO Port: 0xe408
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
Enabling APIC mode: Logical Cluster. Using 1 I/O APICs, target cpus f
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130028
Kernel command line: ro root=LABEL=/ video=matroxfb:vesa:0x11A console=ttyS0,115200n8 console=tty0
nmi_watchdog=1
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c035f000 soft=c035b000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1005.042 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
console [ttyS0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513484k/524204k available (1577k kernel code, 10128k reserved, 607k data, 196k init, 0k
highmem)
virtual kernel memory layout:
fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB)
vmalloc : 0xe0800000 - 0xfffb3000 ( 503 MB)
lowmem : 0xc0000000 - 0xdffeb000 ( 511 MB)
.init : 0xc0327000 - 0xc0358000 ( 196 kB)
.data : 0xc028a7ca - 0xc03227c4 ( 607 kB)
.text : 0xc0100000 - 0xc028a7ca (1577 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 2011.89 BogoMIPS (lpj=4023790)
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
CPU0: Intel Pentium III (Coppermine) stepping 06
Leaving ESR disabled.
Total of 1 processors activated (2011.89 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
WARNING: at arch/x86/kernel/smp_32.c:561 native_smp_call_function_mask()
Pid: 1, comm: swapper Not tainted 2.6.24.1 #1
[<c0105020>] show_trace_log_lvl+0x1a/0x2f
[<c0105990>] show_trace+0x12/0x14
[<c010613d>] dump_stack+0x6c/0x72
[<c0113ab5>] native_smp_call_function_mask+0x44/0x102
[<c0114cc5>] smp_call_function+0x1e/0x22
[<c0125bbc>] on_each_cpu+0x2a/0x57
[<c01170f2>] setup_nmi+0x33/0x4a
[<c0332a22>] setup_IO_APIC+0x929/0xf11
[<c0330178>] native_smp_prepare_cpus+0x487/0x497
[<c03273de>] kernel_init+0x54/0x2c3
[<c0104c83>] kernel_thread_helper+0x7/0x10
=======================
APIC timer registered as dummy, due to nmi_watchdog=1!
Brought up 1 CPUs
net_namespace: 64 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0e30, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region ec00-ec3f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
BUG: NMI Watchdog detected LOCKUP on CPU0, eip c0102b07, registers:
Modules linked in:
Pid: 0, comm: swapper Not tainted (2.6.24.1 #1)
EIP: 0060:[<c0102b07>] EFLAGS: 00000246 CPU: 0
EIP is at default_idle+0x2f/0x43
EAX: 00000000 EBX: c0102ad8 ECX: 010b2000 EDX: fffedb3c
ESI: 00000000 EDI: c1409284 EBP: c0323fb4 ESP: c0323fb4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c0323000 task=c02fc320 task.ti=c0323000)
Stack: c0323fc4 c01025af c140c000 c0357284 c0323fcc c02873a9 c0323ff8 c032792f
00000037 c0327108 00000000 00000004 00009000 c0343b00 00000002 00099800
c0319000 007ab007 00000000
Call Trace:
[<c0105020>] show_trace_log_lvl+0x1a/0x2f
[<c01050d2>] show_stack_log_lvl+0x9d/0xa5
[<c010517d>] show_registers+0xa3/0x1df
[<c0105ba7>] die_nmi+0x81/0xd2
[<c0115d72>] nmi_watchdog_tick+0xd5/0x12a
[<c0105f19>] do_nmi+0x93/0x24b
[<c0289b83>] nmi_stack_correct+0x26/0x2b
[<c01025af>] cpu_idle+0x9a/0xcf
[<c02873a9>] rest_init+0x5d/0x5f
[<c032792f>] start_kernel+0x2e2/0x2ea
[<00000000>] _stext+0x3feff000/0x19
=======================
Code: 36 c0 00 55 89 e5 75 33 80 3d e5 17 32 c0 00 74 2a 89 e0 25 00 f0 ff ff 83 60 0c fd f0 83 04
24 00 fa 8b 40 08 a8 04 75 04 fb f4 <eb> 01 fb 89 e0 25 00 f0 ff ff 83 48 0c 02 eb 02 f3 90 5d c3
55
__________________________________________________________
Sent from Yahoo! Mail - a smarter inbox http://uk.mail.yahoo.com
prev parent reply other threads:[~2008-02-08 23:23 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-02 23:36 [BUG] 2.6.24 refuses to boot - NMI watchdog problem? Chris Rankin
2008-02-05 23:32 ` Andrew Morton
2008-02-06 0:26 ` Chris Rankin
2008-02-06 18:22 ` Len Brown
2008-02-06 18:32 ` Andrew Morton
2008-02-07 19:58 ` Chris Rankin
2008-02-07 20:26 ` Andrew Morton
2008-02-07 20:26 ` Andrew Morton
2008-02-07 22:22 ` Chris Rankin
2008-02-08 23:22 ` Chris Rankin [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7606.9306.qm@web52905.mail.re2.yahoo.com \
--to=rankincj@yahoo.com \
--cc=akpm@linux-foundation.org \
--cc=lenb@kernel.org \
--cc=linux-acpi@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.