From: Russell Senior <seniorr@aracnet.com>
To: Gerard Roudier <groudier@free.fr>
Cc: linux-scsi@vger.kernel.org
Subject: PROBLEM: SYM53C8XX errors while reading tape
Date: 22 Nov 2002 00:49:30 -0800 [thread overview]
Message-ID: <86smxuj8f9.fsf@coulee.tdb.com> (raw)
[1.] One line summary of the problem:
SYM53C8XX errors while reading tape
[2.] Full description of the problem/report:
I just installed a new Seagate Scorpion 24 tape drive (DDS3 4mm DAT)
attached to an old NCR53c810 PCI SCSI controller and was trying it
out. I did a:
mt -f /dev/nst0 setblk 32768
tar -C / -b 64 -clvf /dev/nst0 .
and that seemed to work fine, but when I tried to verify or read, with
something like this:
mt -f /dev/nst0 rewind
tar -C / -b 64 -dlf /dev/nst0
after a variable delay, i.e. some distance through the process, I get
messages to the shell:
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: /dev/nst0: Cannot read: Input/output error
tar: Too many errors, quitting
tar: Error is not recoverable: exiting now
I can still access the drive afterwards, though the block size gets
reset. In /var/log/messages, I see:
Nov 22 00:07:19 celilo kernel: sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14).
Nov 22 00:07:19 celilo kernel: sym0: script cmd = 88080000
Nov 22 00:07:19 celilo kernel: sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff.
Nov 22 00:07:19 celilo kernel: sym0: SCSI BUS reset detected.
Nov 22 00:07:20 celilo kernel: sym0: SCSI BUS has been reset.
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Current st09:00: sense key Unit Attention
Nov 22 00:07:23 celilo kernel: Additional sense indicates Power on,reset,or bus device reset occurred
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
Nov 22 00:07:23 celilo kernel: st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Nov 22 00:07:23 celilo kernel: Additional sense indicates Logical unit is in process of becoming ready
This particular set of messages came under linux-2.4.18, but I had
seen what seemed like the same thing under linux-2.5.40 and regressed
to 2.4.18 to see if it was a kernel specific problem.
I don't know what the /sbin/fsck those messages mean, in particular
the originating error message, codes and register dump. Basically,
that is what I am looking for, some indication what the problem might be.
[3.] Keywords (i.e., modules, networking, kernel):
SCSI, error message
[4.] Kernel version (from /proc/version):
Linux version 2.4.18 (root@celilo) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP Sat Jun 1 21:08:44 PDT 2002
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Linux celilo 2.4.18 #2 SMP Sat Jun 1 21:08:44 PDT 2002 i686 unknown unknown GNU/Linux
Gnu C 2.95.4
Gnu make 3.80
util-linux 2.11u
mount 2.11u
modutils 2.4.19
e2fsprogs 1.32
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 3.1.0
Net-tools 1.60
Kbd 1.06
Sh-utils 4.5.3
Modules Loaded ide-scsi
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 999.530
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1992.29
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 999.530
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1998.84
[7.3.] Module information (from /proc/modules):
ide-scsi 7808 0
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
$ cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
a000-a007 : Promise Technology, Inc. 20268
a000-a007 : ide2
a400-a403 : Promise Technology, Inc. 20268
a402-a402 : ide2
a800-a807 : Promise Technology, Inc. 20268
a800-a807 : ide3
ac00-ac03 : Promise Technology, Inc. 20268
ac02-ac02 : ide3
b000-b00f : Promise Technology, Inc. 20268
b000-b007 : ide2
b008-b00f : ide3
b010-b01f : PDC20268
b400-b4ff : 3Dfx Interactive, Inc. Voodoo 3
b800-b8ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
b800-b87f : sym53c8xx
bc00-bc1f : Creative Labs SB Live! EMU10k1
c000-c007 : Creative Labs SB Live!
c400-c407 : Promise Technology, Inc. 20267
c800-c803 : Promise Technology, Inc. 20267
cc00-cc07 : Promise Technology, Inc. 20267
d000-d003 : Promise Technology, Inc. 20267
d400-d43f : Promise Technology, Inc. 20267
d400-d407 : ide4
d408-d40f : ide5
d410-d43f : PDC20267
d800-d83f : Intel Corp. 82557 [Ethernet Pro 100]
d800-d83f : eepro100
dc00-dc0f : VIA Technologies, Inc. Bus Master IDE
dc00-dc07 : ide0
dc08-dc0f : ide1
e000-e01f : VIA Technologies, Inc. UHCI USB
e000-e01f : usb-uhci
e400-e41f : VIA Technologies, Inc. UHCI USB (#2)
e400-e41f : usb-uhci
e800-e81f : VIA Technologies, Inc. UHCI USB (#3)
e800-e81f : usb-uhci
$ cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000d0000-000d27ff : Extension ROM
000d3000-000dafff : Extension ROM
000f0000-000fffff : System ROM
00100000-3ffeffff : System RAM
00100000-00266894 : Kernel code
00266895-002d1a9f : Kernel data
3fff0000-3fff2fff : ACPI Non-volatile Storage
3fff3000-3fffffff : ACPI Tables
f8000000-f9ffffff : 3Dfx Interactive, Inc. Voodoo 3
fa000000-fbffffff : 3Dfx Interactive, Inc. Voodoo 3
fd000000-fd3fffff : VIA Technologies, Inc. VT8633 [Apollo Pro266]
fd400000-fd4fffff : Intel Corp. 82557 [Ethernet Pro 100]
fd500000-fd51ffff : Promise Technology, Inc. 20267
fd520000-fd523fff : Promise Technology, Inc. 20268
fd524000-fd524fff : Intel Corp. 82557 [Ethernet Pro 100]
fd524000-fd524fff : eepro100
fd525000-fd5250ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
fec00000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266] (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra100TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at fd520000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at fa000000 (32-bit, prefetchable) [size=32M]
Region 2: I/O ports at b400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly NCR) 53c810 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at fd525000 (32-bit, non-prefetchable) [size=256]
00:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs: Unknown device 8071
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at bc00 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at c000 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc. Fasttrak100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c400 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at d000 [size=4]
Region 4: I/O ports at d400 [size=64]
Region 5: Memory at fd500000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Server Adapter (PILA8470B)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd524000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d800 [size=64]
Region 2: Memory at fd400000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc: Unknown device 2166
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at dc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 USB Controller: VIA Technologies, Inc. USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
$ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350
Type: Sequential-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: DualPort Model: Reader 2 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: DualPort Model: Reader 2 Rev:
Type: Direct-Access ANSI SCSI revision: 02
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
Here are the relevant messages from dmesg:
SCSI subsystem driver Revision: 1.00
sym.0.9.0: setting PCI_COMMAND_PARITY...
sym0: <810> rev 0x2 on pci bus 0 device 9 function 0 irq 11
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7350
Type: Sequential-Access ANSI SCSI revision: 02
st: Version 20020205, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 1, lun 0
[...]
sym0:1: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 8)
st0: Block limits 1 - 16777215 bytes.
This is the end of the boot messages, then when the error occurs, I
get the following:
sym0:1: ERROR (0:c8) (1-21-85) (8/13/0) @ (scripta 92c:19001b14).
sym0: script cmd = 88080000
sym0: regdump: da 10 80 13 47 08 01 1f 00 01 81 21 80 00 09 00 00 20 e9 37 08 ff ff ff.
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
st0: Error with sense data: Current st09:00: sense key Unit Attention
Additional sense indicates Power on,reset,or bus device reset occurred
st0: Error with sense data: Info fld=0x0, Current st09:00: sense key Not Ready
Additional sense indicates Logical unit is in process of becoming ready
[...]
--
Russell Senior ``I've seen every kind of critter God ever made,
seniorr@aracnet.com and I ain't never seen a meaner, lower, more
stinkin' yellow hypocrite than you!''
-- Burl Ives as Rufus Hennessy
next reply other threads:[~2002-11-22 8:49 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-11-22 8:49 Russell Senior [this message]
2002-11-24 21:56 ` PROBLEM: SYM53C8XX errors while reading tape Gérard Roudier
[not found] <86k7j43gh7.fsf@coulee.tdb.com>
2002-11-23 17:57 ` Mr. James W. Laferriere
2002-11-23 22:45 ` Mr. James W. Laferriere
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=86smxuj8f9.fsf@coulee.tdb.com \
--to=seniorr@aracnet.com \
--cc=groudier@free.fr \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.