Re: [PATCH v3 4/9] usb: dwc3-generic: Add STih407 support

[Mattijs Korpershoek <mkorpershoek@baylibre.com>]

Hi Patrice,

Thank you for the patch.

On lun., janv. 20, 2025 at 09:01, Patrice Chotard <patrice.chotard@foss.st.com> wrote:

> Add STi glue logic to manage the DWC3 HC on STiH407
> SoC family. It configures the internal glue logic and
> syscfg registers.
>
> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Marek Vasut <marex@denx.de>
>
> ---
>
> Changes in v3:
>   - Replace debug() by dev_err()
>   - check return value of syscon_regmap_lookup_by_phandle()
>
> Changes in v2:
>   - add dwc3-sti.c DWC3 wrapper as done for dwc3-am62.c
>
>  MAINTAINERS                         |   1 +
>  drivers/usb/dwc3/Kconfig            |   6 ++
>  drivers/usb/dwc3/Makefile           |   1 +
>  drivers/usb/dwc3/dwc3-generic-sti.c | 132 ++++++++++++++++++++++++++++
>  4 files changed, 140 insertions(+)
>  create mode 100644 drivers/usb/dwc3/dwc3-generic-sti.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 8c6c0c2a4bc..5d7e251e601 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -656,6 +656,7 @@ F:	drivers/mmc/sti_sdhci.c
>  F:	drivers/reset/sti-reset.c
>  F:	drivers/serial/serial_sti_asc.c
>  F:	drivers/sysreset/sysreset_sti.c
> +F:	drivers/usb/host/dwc3-sti.c
>  F:	drivers/timer/arm_global_timer.c
>  F:	drivers/usb/host/dwc3-sti-glue.c
>  F:	include/dwc3-sti-glue.h
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index 0100723a68b..7d58ae65fb6 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -87,6 +87,12 @@ config USB_DWC3_LAYERSCAPE
>  	  Host and Peripheral operation modes are supported. OTG is not
>  	  supported.
>  
> +config USB_DWC3_STI
> +	bool "STi USB wrapper"
> +	depends on DM_USB && USB_DWC3_GENERIC && SYSCON
> +	help
> +	  Select this for STi Platforms.

The improvements done in v3 based on the comments from v2 look good to me.
However, checkpatch seems unhappy about this:

$ ./scripts/checkpatch.pl --git --u-boot --git master..HEAD

--------------------------------------------------------------
Commit 2a4d2432f669 ("usb: dwc3-generic: Add STih407 support")
--------------------------------------------------------------
WARNING: please write a paragraph that describes the config symbol fully
#42: FILE: drivers/usb/dwc3/Kconfig:90:
+config USB_DWC3_STI

Can't we reuse the help description from 'config USB_XHCI_STI' ?
I'm sorry I missed this before.

With that addressed, please add:

Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>

> +
>  menu "PHY Subsystem"
>  
>  config USB_DWC3_PHY_OMAP
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index a085c9d4628..985206eafe4 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -15,3 +15,4 @@ obj-$(CONFIG_USB_DWC3_UNIPHIER)		+= dwc3-uniphier.o
>  obj-$(CONFIG_USB_DWC3_LAYERSCAPE)	+= dwc3-layerscape.o
>  obj-$(CONFIG_USB_DWC3_PHY_OMAP)		+= ti_usb_phy.o
>  obj-$(CONFIG_USB_DWC3_PHY_SAMSUNG)	+= samsung_usb_phy.o
> +obj-$(CONFIG_USB_DWC3_STI)		+= dwc3-generic-sti.o
> diff --git a/drivers/usb/dwc3/dwc3-generic-sti.c b/drivers/usb/dwc3/dwc3-generic-sti.c
> new file mode 100644
> index 00000000000..2ff640cede4
> --- /dev/null
> +++ b/drivers/usb/dwc3/dwc3-generic-sti.c
> @@ -0,0 +1,132 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
> +/*
> + * STi specific glue layer for DWC3
> + *
> + * Copyright (C) 2025, STMicroelectronics - All Rights Reserved
> + */
> +
> +#include <reset.h>
> +#include <regmap.h>
> +#include <syscon.h>
> +#include <asm/io.h>
> +#include <dm/device.h>
> +#include <dm/device_compat.h>
> +#include <dm/read.h>
> +#include <linux/usb/otg.h>
> +#include "dwc3-generic.h"
> +
> +/* glue registers */
> +#define CLKRST_CTRL		0x00
> +#define AUX_CLK_EN		BIT(0)
> +#define SW_PIPEW_RESET_N	BIT(4)
> +#define EXT_CFG_RESET_N		BIT(8)
> +
> +#define XHCI_REVISION		BIT(12)
> +
> +#define USB2_VBUS_MNGMNT_SEL1	0x2C
> +#define USB2_VBUS_UTMIOTG	0x1
> +
> +#define SEL_OVERRIDE_VBUSVALID(n)	((n) << 0)
> +#define SEL_OVERRIDE_POWERPRESENT(n)	((n) << 4)
> +#define SEL_OVERRIDE_BVALID(n)		((n) << 8)
> +
> +/* Static DRD configuration */
> +#define USB3_CONTROL_MASK		0xf77
> +
> +#define USB3_DEVICE_NOT_HOST		BIT(0)
> +#define USB3_FORCE_VBUSVALID		BIT(1)
> +#define USB3_DELAY_VBUSVALID		BIT(2)
> +#define USB3_SEL_FORCE_OPMODE		BIT(4)
> +#define USB3_FORCE_OPMODE(n)		((n) << 5)
> +#define USB3_SEL_FORCE_DPPULLDOWN2	BIT(8)
> +#define USB3_FORCE_DPPULLDOWN2		BIT(9)
> +#define USB3_SEL_FORCE_DMPULLDOWN2	BIT(10)
> +#define USB3_FORCE_DMPULLDOWN2		BIT(11)
> +
> +static void dwc3_stih407_glue_configure(struct udevice *dev, int index,
> +					enum usb_dr_mode mode)
> +{
> +	struct dwc3_glue_data *glue = dev_get_plat(dev);
> +	struct regmap *regmap;
> +	ulong syscfg_base;
> +	ulong syscfg_offset;
> +	ulong glue_base;
> +	int ret;
> +
> +	/* deassert both powerdown and softreset */
> +	ret = reset_deassert_bulk(&glue->resets);
> +	if (ret) {
> +		dev_err(dev, "reset_deassert_bulk error: %d\n", ret);
> +		return;
> +	}
> +
> +	regmap = syscon_regmap_lookup_by_phandle(dev, "st,syscfg");
> +	if (IS_ERR(regmap)) {
> +		dev_err(dev, "unable to get st,syscfg, dev %s\n", dev->name);
> +		return;
> +	}
> +
> +	syscfg_base = regmap->ranges[0].start;
> +	glue_base = dev_read_addr_index(dev, 0);
> +	syscfg_offset = dev_read_addr_index(dev, 1);
> +
> +	clrbits_le32(syscfg_base + syscfg_offset, USB3_CONTROL_MASK);
> +
> +	/* glue drd init */
> +	switch (mode) {
> +	case USB_DR_MODE_PERIPHERAL:
> +		clrbits_le32(syscfg_base + syscfg_offset,
> +			     USB3_DELAY_VBUSVALID | USB3_SEL_FORCE_OPMODE |
> +			     USB3_FORCE_OPMODE(0x3) | USB3_SEL_FORCE_DPPULLDOWN2 |
> +			     USB3_FORCE_DPPULLDOWN2 | USB3_SEL_FORCE_DMPULLDOWN2 |
> +			     USB3_FORCE_DMPULLDOWN2);
> +
> +		setbits_le32(syscfg_base + syscfg_offset,
> +			     USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID);
> +		break;
> +
> +	case USB_DR_MODE_HOST:
> +		clrbits_le32(syscfg_base + syscfg_offset,
> +			     USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID |
> +			     USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3) |
> +			     USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2 |
> +			     USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
> +
> +		setbits_le32(syscfg_base + syscfg_offset, USB3_DELAY_VBUSVALID);
> +		break;
> +
> +	default:
> +		dev_err(dev, "Unsupported mode of operation %d\n", mode);
> +		return;
> +	}
> +
> +	/* glue init */
> +	setbits_le32(glue_base + CLKRST_CTRL, AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION);
> +	clrbits_le32(glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N);
> +
> +	/* configure mux for vbus, powerpresent and bvalid signals */
> +	setbits_le32(glue_base + USB2_VBUS_MNGMNT_SEL1,
> +		     SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
> +		     SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
> +		     SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG));
> +	setbits_le32(glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N);
> +};
> +
> +struct dwc3_glue_ops stih407_ops = {
> +	.glue_configure = dwc3_stih407_glue_configure,
> +};
> +
> +static const struct udevice_id dwc3_sti_match[] = {
> +	{ .compatible = "st,stih407-dwc3", .data = (ulong)&stih407_ops},
> +	{ /* sentinel */ }
> +};
> +
> +U_BOOT_DRIVER(dwc3_sti_wrapper) = {
> +	.name = "dwc3-sti",
> +	.id = UCLASS_SIMPLE_BUS,
> +	.of_match = dwc3_sti_match,
> +	.bind = dwc3_glue_bind,
> +	.probe = dwc3_glue_probe,
> +	.remove = dwc3_glue_remove,
> +	.plat_auto = sizeof(struct dwc3_glue_data),
> +};
> -- 
> 2.25.1