From: Emil Williams <emil@chud.cyou>
To: linux-wireless@vger.kernel.org
Cc: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Subject: iwlwifi: AX211 (CNVi 8086:7a70) probe fails with -110 after kexec; PCI remove/rescan recovers
Date: Wed, 14 Oct 2026 11:20:49 +0000 [thread overview]
Message-ID: <87a4og34vi.fsf@chud.cyou> (raw)
[-- Attachment #1: Type: text/plain, Size: 1980 bytes --]
Summary: after kexec, iwlwifi probe on 0000:00:14.3 fails with -110.
A clean boot works. Echoing 1 to the device's remove then to
/sys/bus/pci/rescan recovers it without reboot. A PCI reset does not.
I have not tested this on a newer BIOS, it may very well fix this issue,
however that is a hard ask for most and the issue is fixable past boot.
I use the Gentoo kexec OpenRC service for setting up kexec,
which just boots the last kernel used by default.
Bluetooth seems to be available, however I don't use Bluetooth to any extent.
Effective Repeatable Solution:
echo 1 > /sys/bus/pci/devices/0000:00:14.3/remove
echo 1 > /sys/bus/pci/rescan
Note that I ran a reset too (to no apparent change) before the
remove/rescan in the below log.
Kernel (standard and untouched USE flag wise):
6.18.54-gentoo-dist-hardened
sys-kernel/linux-firmware-20260916
(note: older kernel versions in the 6.1x group had the same results)
Hardware:
Board Vendor : MSI
Board Name : PRO B760-P WIFI (MS-7D98)
Board Version : 2.0
BIOS Vendor : American Megatrends International, LLC.
Bios Version : A.Q3
BIOS date : 08/29/2023
Truncated Logs (see dmesg.log attachment):
00:14.3 Network controller [0280]: Intel Corporation 700 Series Chipset CNVi WiFi [8086:7a70] (rev 11)
[ 6.560889] iwlwifi 0000:00:14.3: CSR_RESET = 0x10
[ 6.560892] iwlwifi 0000:00:14.3: Host monitor block 0x0 vector 0x0
[ 6.560915] iwlwifi 0000:00:14.3: value [iter 0]: 0x3f1d0430
...
[ 6.610796] iwlwifi 0000:00:14.3: probe with driver iwlwifi failed with error -110
[ 732.520454] iwlwifi 0000:00:14.3: Detected crf-id 0x400410, cnv-id 0x80401 wfpm id 0x80000020
[ 732.520490] iwlwifi 0000:00:14.3: PCI dev 7a70/0094, rev=0x430, rfid=0x2010d000
[ 732.520499] iwlwifi 0000:00:14.3: Detected Intel(R) Wi-Fi 6E AX211 160MHz
[ 732.520992] Loading firmware: iwlwifi-so-a0-gf-a0-89.ucode
[ 732.533758] iwlwifi 0000:00:14.3: loaded firmware version 89.d2579d43.0 so-a0-gf-a0-89.ucode op_mode iwlmvm
[-- Attachment #2: dmesg iwlwifi log after kexec --]
[-- Type: text/plain, Size: 4920 bytes --]
[ 6.560889] iwlwifi 0000:00:14.3: CSR_RESET = 0x10
[ 6.560892] iwlwifi 0000:00:14.3: Host monitor block 0x0 vector 0x0
[ 6.560915] iwlwifi 0000:00:14.3: value [iter 0]: 0x3f1d0430
[ 6.560918] iwlwifi 0000:00:14.3: value [iter 1]: 0x3f1d0430
[ 6.560920] iwlwifi 0000:00:14.3: value [iter 2]: 0x3f1d0030
[ 6.560922] iwlwifi 0000:00:14.3: value [iter 3]: 0x3f1d0030
[ 6.560925] iwlwifi 0000:00:14.3: value [iter 4]: 0x3f1d0030
[ 6.560927] iwlwifi 0000:00:14.3: value [iter 5]: 0x3f1d0030
[ 6.560929] iwlwifi 0000:00:14.3: value [iter 6]: 0x3f1d0030
[ 6.560931] iwlwifi 0000:00:14.3: value [iter 7]: 0x3f1d0030
[ 6.560934] iwlwifi 0000:00:14.3: value [iter 8]: 0x3f1d0030
[ 6.560936] iwlwifi 0000:00:14.3: value [iter 9]: 0x3f1d0430
[ 6.560938] iwlwifi 0000:00:14.3: value [iter 10]: 0x3f1d0430
[ 6.560941] iwlwifi 0000:00:14.3: value [iter 11]: 0x3f1d0430
[ 6.560943] iwlwifi 0000:00:14.3: value [iter 12]: 0x3f1d0430
[ 6.560945] iwlwifi 0000:00:14.3: value [iter 13]: 0x3f1d0430
[ 6.560948] iwlwifi 0000:00:14.3: value [iter 14]: 0x3f1d0430
[ 6.560953] iwlwifi 0000:00:14.3: Host monitor block 0x0 vector 0x1
[ 6.560971] iwlwifi 0000:00:14.3: value [iter 0]: 0x040066c2
[ 6.560974] iwlwifi 0000:00:14.3: value [iter 1]: 0x040066c2
[ 6.560976] iwlwifi 0000:00:14.3: value [iter 2]: 0x040066c2
[ 6.560978] iwlwifi 0000:00:14.3: value [iter 3]: 0x040066c2
[ 6.560981] iwlwifi 0000:00:14.3: value [iter 4]: 0x040066c2
[ 6.560983] iwlwifi 0000:00:14.3: value [iter 5]: 0x040066c2
[ 6.560985] iwlwifi 0000:00:14.3: value [iter 6]: 0x040066c2
[ 6.560988] iwlwifi 0000:00:14.3: value [iter 7]: 0x040066c2
[ 6.560990] iwlwifi 0000:00:14.3: value [iter 8]: 0x040066c2
[ 6.560992] iwlwifi 0000:00:14.3: value [iter 9]: 0x040066c2
[ 6.560994] iwlwifi 0000:00:14.3: value [iter 10]: 0x040066c2
[ 6.560997] iwlwifi 0000:00:14.3: value [iter 11]: 0x040066c2
[ 6.560999] iwlwifi 0000:00:14.3: value [iter 12]: 0x040066c2
[ 6.561001] iwlwifi 0000:00:14.3: value [iter 13]: 0x040066c2
[ 6.561004] iwlwifi 0000:00:14.3: value [iter 14]: 0x040066c2
[ 6.561005] iwlwifi 0000:00:14.3: Host monitor block 0x0 vector 0x6
[ 6.561027] iwlwifi 0000:00:14.3: value [iter 0]: 0xb00c7c75
[ 6.561029] iwlwifi 0000:00:14.3: value [iter 1]: 0xb00c7c75
[ 6.561032] iwlwifi 0000:00:14.3: value [iter 2]: 0xb00c7c75
[ 6.561034] iwlwifi 0000:00:14.3: value [iter 3]: 0xb00c7c75
[ 6.561036] iwlwifi 0000:00:14.3: value [iter 4]: 0xb00c7c75
[ 6.561039] iwlwifi 0000:00:14.3: value [iter 5]: 0xb00c7c75
[ 6.561041] iwlwifi 0000:00:14.3: value [iter 6]: 0xa00c7c75
[ 6.561043] iwlwifi 0000:00:14.3: value [iter 7]: 0xa00c7c75
[ 6.561046] iwlwifi 0000:00:14.3: value [iter 8]: 0xa00c7c75
[ 6.561048] iwlwifi 0000:00:14.3: value [iter 9]: 0xe00c7c75
[ 6.561050] iwlwifi 0000:00:14.3: value [iter 10]: 0xe00c7c75
[ 6.561053] iwlwifi 0000:00:14.3: value [iter 11]: 0xe00c7c75
[ 6.561055] iwlwifi 0000:00:14.3: value [iter 12]: 0xe00c7c75
[ 6.561057] iwlwifi 0000:00:14.3: value [iter 13]: 0xf00c7c75
[ 6.561059] iwlwifi 0000:00:14.3: value [iter 14]: 0xf00c7c75
[ 6.561061] iwlwifi 0000:00:14.3: Host monitor block 0x22 vector 0x0
[ 6.561083] iwlwifi 0000:00:14.3: value [iter 0]: 0xf9cec019
[ 6.610796] iwlwifi 0000:00:14.3: probe with driver iwlwifi failed with error -110
[ 732.520454] iwlwifi 0000:00:14.3: Detected crf-id 0x400410, cnv-id 0x80401 wfpm id 0x80000020
[ 732.520490] iwlwifi 0000:00:14.3: PCI dev 7a70/0094, rev=0x430, rfid=0x2010d000
[ 732.520499] iwlwifi 0000:00:14.3: Detected Intel(R) Wi-Fi 6E AX211 160MHz
[ 732.520992] Loading firmware: iwlwifi-so-a0-gf-a0-89.ucode
[ 732.533758] iwlwifi 0000:00:14.3: loaded firmware version 89.d2579d43.0 so-a0-gf-a0-89.ucode op_mode iwlmvm
[ 732.805125] iwlwifi 0000:00:14.3: WFPM_UMAC_PD_NOTIFICATION: 0x20
[ 732.805157] iwlwifi 0000:00:14.3: WFPM_LMAC2_PD_NOTIFICATION: 0x1f
[ 732.805171] iwlwifi 0000:00:14.3: WFPM_AUTH_KEY_0: 0x90
[ 732.805202] iwlwifi 0000:00:14.3: CNVI_SCU_SEQ_DATA_DW9: 0x0
[ 732.805368] iwlwifi 0000:00:14.3: Detected RF GF, rfid=0x2010d000
[ 732.805381] Loading firmware: iwlwifi-so-a0-gf-a0.pnvm
[ 732.806218] iwlwifi 0000:00:14.3: RFIm is deactivated, reason = 5
[ 732.892495] iwlwifi 0000:00:14.3: base HW address: xx:xx:xx:xx:xx:xx
[ 732.924669] iwlwifi 0000:00:14.3 wlo1: renamed from wlan0
[ 733.137818] iwlwifi 0000:00:14.3: WFPM_UMAC_PD_NOTIFICATION: 0x20
[ 733.137860] iwlwifi 0000:00:14.3: WFPM_LMAC2_PD_NOTIFICATION: 0x1f
[ 733.137892] iwlwifi 0000:00:14.3: WFPM_AUTH_KEY_0: 0x90
[ 733.137904] iwlwifi 0000:00:14.3: CNVI_SCU_SEQ_DATA_DW9: 0x0
[ 733.138918] iwlwifi 0000:00:14.3: RFIm is deactivated, reason = 5
next reply other threads:[~2026-10-14 11:20 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-14 11:20 Emil Williams [this message]
-- strict thread matches above, loose matches on Subject: below --
2026-10-14 11:25 iwlwifi: AX211 (CNVi 8086:7a70) probe fails with -110 after kexec; PCI remove/rescan recovers Emil Williams
2026-10-14 11:11 Emil Williams
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87a4og34vi.fsf@chud.cyou \
--to=emil@chud.cyou \
--cc=linux-wireless@vger.kernel.org \
--cc=miriam.rachel.korenblit@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.