From mboxrd@z Thu Jan 1 00:00:00 1970 From: gregory.clement@bootlin.com (Gregory CLEMENT) Date: Wed, 26 Sep 2018 14:28:06 +0200 Subject: [PATCH v3] arm64: dts: add support for SolidRun Clearfog GT 8K In-Reply-To: <61a8e08f1e36078e1cec44ed16bf122c23c98e9c.1537642783.git.baruch@tkos.co.il> (Baruch Siach's message of "Sat, 22 Sep 2018 21:59:43 +0300") References: <61a8e08f1e36078e1cec44ed16bf122c23c98e9c.1537642783.git.baruch@tkos.co.il> Message-ID: <87k1n8e949.fsf@bootlin.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hi Baruch, On sam., sept. 22 2018, Baruch Siach wrote: > The SolidRun Clearfog GT-8K is based on Marvell Armada 8040 SoC. > > https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k > > The following devices were tested with this DT on top of kernel > v4.19-rc4: > > * 1GB Ethernet WAN > > * 4 ports 1GB Ethernet switch (2.5GB uplink) > > * SFP port > > * SATA on CON3 PCIe slot > > * USB3 type A port > > * SD card and eMMC > > * 2 LEDs > > * 2 push buttons > > Signed-off-by: Baruch Siach Applied on mvebu/dt64, I've just fix the following block alignment issue reported by checkpatch: WARNING: Block comments should align the * on each line #195: FILE: arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts:141: + /* + * MPP Bus: Thanks, Gregory > --- > v3: > > * Change LEDs labels > > * Note the SFP port in the commit log > > * Cosmetic DT formatting change > > v2: > * Add SATA node > > * Set front button code to KEY_WPS_BUTTON > > * Use LEDs labels more aligned to conversion > > * Document the marvell,reg-init meaning > --- > arch/arm64/boot/dts/marvell/Makefile | 1 + > .../marvell/armada-8040-clearfog-gt-8k.dts | 434 ++++++++++++++++++ > 2 files changed, 435 insertions(+) > create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts > > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile > index ea9d49f2a911..eca8bac6303a 100644 > --- a/arch/arm64/boot/dts/marvell/Makefile > +++ b/arch/arm64/boot/dts/marvell/Makefile > @@ -3,6 +3,7 @@ > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb > +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb > diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts > new file mode 100644 > index 000000000000..2e06d82bec58 > --- /dev/null > +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts > @@ -0,0 +1,434 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2018 SolidRun ltd. > + * Based on Marvell MACCHIATOBin board > + * > + * Device Tree file for SolidRun's ClearFog GT 8K > + */ > + > +#include "armada-8040.dtsi" > + > +#include > +#include > + > +/ { > + model = "SolidRun ClearFog GT 8K"; > + compatible = "solidrun,clearfog-gt-8k", "marvell,armada8040", > + "marvell,armada-ap806-quad", "marvell,armada-ap806"; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + memory at 00000000 { > + device_type = "memory"; > + reg = <0x0 0x0 0x0 0x80000000>; > + }; > + > + aliases { > + ethernet0 = &cp1_eth1; > + ethernet1 = &cp0_eth0; > + ethernet2 = &cp1_eth2; > + }; > + > + v_3_3: regulator-3-3v { > + compatible = "regulator-fixed"; > + regulator-name = "v_3_3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + status = "okay"; > + }; > + > + v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { > + compatible = "regulator-fixed"; > + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_xhci_vbus_pins>; > + regulator-name = "v_5v0_usb3_hst_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + status = "okay"; > + }; > + > + usb3h0_phy: usb3_phy0 { > + compatible = "usb-nop-xceiv"; > + vcc-supply = <&v_5v0_usb3_hst_vbus>; > + }; > + > + sfp_cp0_eth0: sfp-cp0-eth0 { > + compatible = "sff,sfp"; > + i2c-bus = <&cp0_i2c1>; > + mod-def0-gpio = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>; > + tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_sfp_present_pins &cp1_sfp_tx_disable_pins>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-0 = <&cp0_led0_pins > + &cp0_led1_pins>; > + pinctrl-names = "default"; > + /* No designated function for these LEDs at the moment */ > + led0 { > + label = "clearfog-gt-8k:green:led0"; > + gpios = <&cp0_gpio2 8 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + led1 { > + label = "clearfog-gt-8k:green:led1"; > + gpios = <&cp0_gpio2 9 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + }; > + > + keys { > + compatible = "gpio-keys"; > + pinctrl-0 = <&cp0_gpio_reset_pins &cp1_wps_button_pins>; > + pinctrl-names = "default"; > + > + button_0 { > + /* The rear button */ > + label = "Rear Button"; > + gpios = <&cp0_gpio2 7 GPIO_ACTIVE_LOW>; > + linux,can-disable; > + linux,code = ; > + }; > + > + button_1 { > + /* The wps button */ > + label = "WPS Button"; > + gpios = <&cp1_gpio1 30 GPIO_ACTIVE_LOW>; > + linux,can-disable; > + linux,code = ; > + }; > + }; > +}; > + > +&uart0 { > + status = "okay"; > + pinctrl-0 = <&uart0_pins>; > + pinctrl-names = "default"; > +}; > + > +&ap_sdhci0 { > + bus-width = <8>; > + no-1-8-v; > + no-sd; > + no-sdio; > + non-removable; > + status = "okay"; > + vqmmc-supply = <&v_3_3>; > +}; > + > +&cp0_i2c0 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_i2c0_pins>; > + status = "okay"; > +}; > + > +&cp0_i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_i2c1_pins>; > + status = "okay"; > +}; > + > +&cp0_pinctrl { > + /* > + * MPP Bus: > + * [0-31] = 0xff: Keep default CP0_shared_pins: > + * [11] CLKOUT_MPP_11 (out) > + * [23] LINK_RD_IN_CP2CP (in) > + * [25] CLKOUT_MPP_25 (out) > + * [29] AVS_FB_IN_CP2CP (in) > + * [32, 33, 34] pci0/1/2 reset > + * [35-38] CP0 I2C1 and I2C0 > + * [39] GPIO reset button > + * [40,41] LED0 and LED1 > + * [43] 1512 phy reset > + * [47] USB VBUS EN (active low) > + * [48] FAN PWM > + * [49] SFP+ present signal > + * [50] TPM interrupt > + * [51] WLAN0 disable > + * [52] WLAN1 disable > + * [53] LTE disable > + * [54] NFC reset > + * [55] Micro SD card detect > + * [56-61] Micro SD > + */ > + > + cp0_pci0_reset_pins: pci0-reset-pins { > + marvell,pins = "mpp32"; > + marvell,function = "gpio"; > + }; > + > + cp0_pci1_reset_pins: pci1-reset-pins { > + marvell,pins = "mpp33"; > + marvell,function = "gpio"; > + }; > + > + cp0_pci2_reset_pins: pci2-reset-pins { > + marvell,pins = "mpp34"; > + marvell,function = "gpio"; > + }; > + > + cp0_i2c1_pins: i2c1-pins { > + marvell,pins = "mpp35", "mpp36"; > + marvell,function = "i2c1"; > + }; > + > + cp0_i2c0_pins: i2c0-pins { > + marvell,pins = "mpp37", "mpp38"; > + marvell,function = "i2c0"; > + }; > + > + cp0_gpio_reset_pins: gpio-reset-pins { > + marvell,pins = "mpp39"; > + marvell,function = "gpio"; > + }; > + > + cp0_led0_pins: led0-pins { > + marvell,pins = "mpp40"; > + marvell,function = "gpio"; > + }; > + > + cp0_led1_pins: led1-pins { > + marvell,pins = "mpp41"; > + marvell,function = "gpio"; > + }; > + > + cp0_copper_eth_phy_reset: copper-eth-phy-reset { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + > + cp0_xhci_vbus_pins: xhci0-vbus-pins { > + marvell,pins = "mpp47"; > + marvell,function = "gpio"; > + }; > + > + cp0_fan_pwm_pins: fan-pwm-pins { > + marvell,pins = "mpp48"; > + marvell,function = "gpio"; > + }; > + > + cp0_sfp_present_pins: sfp-present-pins { > + marvell,pins = "mpp49"; > + marvell,function = "gpio"; > + }; > + > + cp0_tpm_irq_pins: tpm-irq-pins { > + marvell,pins = "mpp50"; > + marvell,function = "gpio"; > + }; > + > + cp0_sdhci_pins: sdhci-pins { > + marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", > + "mpp60", "mpp61"; > + marvell,function = "sdio"; > + }; > +}; > + > +&cp0_gpio2 { > + sata_reset { > + gpio-hog; > + gpios = <1 GPIO_ACTIVE_HIGH>; > + output-high; > + }; > +}; > + > +&cp0_ethernet { > + status = "okay"; > +}; > + > +/* SFP */ > +&cp0_eth0 { > + status = "okay"; > + phy-mode = "10gbase-kr"; > + managed = "in-band-status"; > + phys = <&cp0_comphy2 0>; > + sfp = <&sfp_cp0_eth0>; > +}; > + > +&cp0_sdhci0 { > + broken-cd; > + bus-width = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_sdhci_pins>; > + status = "okay"; > + vqmmc-supply = <&v_3_3>; > +}; > + > +&cp1_pinctrl { > + /* > + * MPP Bus: > + * [0-5] TDM > + * [6] VHV Enable > + * [7] CP1 SPI0 CSn1 (FXS) > + * [8] CP1 SPI0 CSn0 (TPM) > + * [9.11]CP1 SPI0 MOSI/MISO/CLK > + * [13] CP1 SPI1 MISO (TDM and SPI ROM shared) > + * [14] CP1 SPI1 CS0n (64Mb SPI ROM) > + * [15] CP1 SPI1 MOSI (TDM and SPI ROM shared) > + * [16] CP1 SPI1 CLK (TDM and SPI ROM shared) > + * [24] Topaz switch reset > + * [26] Buzzer > + * [27] CP1 SMI MDIO > + * [28] CP1 SMI MDC > + * [29] CP0 10G SFP TX Disable > + * [30] WPS button > + * [31] Front panel button > + */ > + > + cp1_spi1_pins: spi1-pins { > + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; > + marvell,function = "spi1"; > + }; > + > + cp1_switch_reset_pins: switch-reset-pins { > + marvell,pins = "mpp24"; > + marvell,function = "gpio"; > + }; > + > + cp1_ge_mdio_pins: ge-mdio-pins { > + marvell,pins = "mpp27", "mpp28"; > + marvell,function = "ge"; > + }; > + > + cp1_sfp_tx_disable_pins: sfp-tx-disable-pins { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + > + cp1_wps_button_pins: wps-button-pins { > + marvell,pins = "mpp30"; > + marvell,function = "gpio"; > + }; > +}; > + > +&cp1_sata0 { > + pinctrl-0 = <&cp0_pci1_reset_pins>; > + status = "okay"; > +}; > + > +&cp1_mdio { > + pinctrl-names = "default"; > + pinctrl-0 = <&cp1_ge_mdio_pins>; > + status = "okay"; > + > + ge_phy: ethernet-phy at 0 { > + /* LED0 - GB link > + * LED1 - on: link, blink: activity > + */ > + marvell,reg-init = <3 16 0 0x1017>; > + reg = <0>; > + }; > + > + switch0: switch0 at 4 { > + compatible = "marvell,mv88e6085"; > + reg = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&cp1_switch_reset_pins>; > + reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port at 1 { > + reg = <1>; > + label = "lan2"; > + phy-handle = <&switch0phy0>; > + }; > + > + port at 2 { > + reg = <2>; > + label = "lan1"; > + phy-handle = <&switch0phy1>; > + }; > + > + port at 3 { > + reg = <3>; > + label = "lan4"; > + phy-handle = <&switch0phy2>; > + }; > + > + port at 4 { > + reg = <4>; > + label = "lan3"; > + phy-handle = <&switch0phy3>; > + }; > + > + port at 5 { > + reg = <5>; > + label = "cpu"; > + ethernet = <&cp1_eth2>; > + }; > + }; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + switch0phy0: switch0phy0 at 11 { > + reg = <0x11>; > + }; > + > + switch0phy1: switch0phy1 at 12 { > + reg = <0x12>; > + }; > + > + switch0phy2: switch0phy2 at 13 { > + reg = <0x13>; > + }; > + > + switch0phy3: switch0phy3 at 14 { > + reg = <0x14>; > + }; > + }; > + }; > +}; > + > +&cp1_ethernet { > + status = "okay"; > +}; > + > +/* 1G copper */ > +&cp1_eth1 { > + status = "okay"; > + phy-mode = "sgmii"; > + phy = <&ge_phy>; > + phys = <&cp1_comphy3 1>; > +}; > + > +/* Switch uplink */ > +&cp1_eth2 { > + status = "okay"; > + phy-mode = "2500base-x"; > + phys = <&cp1_comphy5 2>; > + fixed-link { > + speed = <2500>; > + full-duplex; > + }; > +}; > + > +&cp1_spi1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&cp1_spi1_pins>; > + status = "okay"; > + > + spi-flash at 0 { > + compatible = "st,w25q32"; > + spi-max-frequency = <50000000>; > + reg = <0>; > + }; > +}; > + > +&cp1_usb3_0 { > + usb-phy = <&usb3h0_phy>; > + status = "okay"; > +}; > -- > 2.19.0 > -- Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com