From: Keita Maehara <maehara@debian.org>
To: alsa-devel@alsa-project.org
Subject: Re: [PATCH 2/2] ac97: YMF743 missing controls support
Date: Wed, 19 Sep 2007 20:34:53 +0900 [thread overview]
Message-ID: <87k5qmanxe.wl%maehara@debian.org> (raw)
In-Reply-To: <87lkb2ao89.wl%maehara@debian.org>
At Wed, 19 Sep 2007 20:28:22 +0900,
Keita Maehara wrote:
> Okay, here it is.
And this is the second part.
From: Keita Maehara <maehara@debian.org>
These patches enable a few YMF743 controls (Tone/3D/IEC958) that won't
be detected with the current version of ALSA.
Signed-off-by: Keita Maehara <maehara@debian.org>
---
The second one contains following changes:
- A chip-specific SPDIF support for YMF743 (It doesn't have AC97
standard SPDIF registers seen on YMF753).
- The implementation for "IEC958 Playback Source" and "IEC958 Mute"
are identical to the ones for YMF753. But there is no "IEC958 Output
Pin" for YMF743.
diff -r a543470c3455 pci/ac97/ac97_codec.c
--- a/pci/ac97/ac97_codec.c Wed Sep 19 07:52:08 2007 +0900
+++ b/pci/ac97/ac97_codec.c Wed Sep 19 07:52:14 2007 +0900
@@ -176,7 +176,7 @@ static const struct ac97_codec_id snd_ac
{ 0x574d4C09, 0xffffffff, "WM9709", NULL, NULL},
{ 0x574d4C12, 0xffffffff, "WM9711,WM9712", patch_wolfson11, NULL},
{ 0x574d4c13, 0xffffffff, "WM9713,WM9714", patch_wolfson13, NULL, AC97_DEFAULT_POWER_OFF},
-{ 0x594d4800, 0xffffffff, "YMF743", NULL, NULL },
+{ 0x594d4800, 0xffffffff, "YMF743", patch_yamaha_ymf743, NULL },
{ 0x594d4802, 0xffffffff, "YMF752", NULL, NULL },
{ 0x594d4803, 0xffffffff, "YMF753", patch_yamaha_ymf753, NULL },
{ 0x83847600, 0xffffffff, "STAC9700,83,84", patch_sigmatel_stac9700, NULL },
@@ -779,6 +779,12 @@ static int snd_ac97_spdif_default_put(st
change |= snd_ac97_update_bits_nolock(ac97, AC97_CXR_AUDIO_MISC,
AC97_CXR_SPDIF_MASK | AC97_CXR_COPYRGT,
v);
+ } else if (ac97->id == AC97_ID_YMF743) {
+ change |= snd_ac97_update_bits_nolock(ac97,
+ AC97_YMF7X3_DIT_CTRL,
+ 0xff38,
+ ((val << 4) & 0xff00) |
+ ((val << 2) & 0x0038));
} else {
unsigned short extst = snd_ac97_read_cache(ac97, AC97_EXTENDED_STATUS);
snd_ac97_update_bits_nolock(ac97, AC97_EXTENDED_STATUS, AC97_EA_SPDIF, 0); /* turn off */
@@ -1375,7 +1381,8 @@ static int snd_ac97_mixer_build(struct s
for (idx = 0; idx < 2; idx++) {
if ((err = snd_ctl_add(card, kctl = snd_ac97_cnew(&snd_ac97_controls_tone[idx], ac97))) < 0)
return err;
- if (ac97->id == AC97_ID_YMF753) {
+ if (ac97->id == AC97_ID_YMF743 ||
+ ac97->id == AC97_ID_YMF753) {
kctl->private_value &= ~(0xff << 16);
kctl->private_value |= 7 << 16;
}
diff -r a543470c3455 pci/ac97/ac97_id.h
--- a/pci/ac97/ac97_id.h Wed Sep 19 07:52:08 2007 +0900
+++ b/pci/ac97/ac97_id.h Wed Sep 19 07:52:14 2007 +0900
@@ -54,6 +54,7 @@
#define AC97_ID_ALC658 0x414c4780
#define AC97_ID_ALC658D 0x414c4781
#define AC97_ID_ALC850 0x414c4790
+#define AC97_ID_YMF743 0x594d4800
#define AC97_ID_YMF753 0x594d4803
#define AC97_ID_VT1616 0x49434551
#define AC97_ID_CM9738 0x434d4941
diff -r a543470c3455 pci/ac97/ac97_patch.c
--- a/pci/ac97/ac97_patch.c Wed Sep 19 07:52:08 2007 +0900
+++ b/pci/ac97/ac97_patch.c Wed Sep 19 07:52:39 2007 +0900
@@ -204,6 +204,7 @@ static inline int is_shared_micin(struct
/* The following snd_ac97_ymf753_... items added by David Shust (dshust@shustring.com) */
+/* Modified for YMF743 by Keita Maehara <maehara@debian.org> */
/* It is possible to indicate to the Yamaha YMF7x3 the type of
speakers being used. */
@@ -296,6 +297,74 @@ static int snd_ac97_ymf7x3_spdif_source_
return -EINVAL;
val = ucontrol->value.enumerated.item[0] << 1;
return snd_ac97_update_bits(ac97, AC97_YMF7X3_DIT_CTRL, 0x0002, val);
+}
+
+static int patch_yamaha_ymf7x3_3d(struct snd_ac97 *ac97)
+{
+ struct snd_kcontrol *kctl;
+ int err;
+
+ kctl = snd_ac97_cnew(&snd_ac97_controls_3d[0], ac97);
+ err = snd_ctl_add(ac97->bus->card, kctl);
+ if (err < 0)
+ return err;
+ strcpy(kctl->id.name, "3D Control - Wide");
+ kctl->private_value = AC97_SINGLE_VALUE(AC97_3D_CONTROL, 9, 7, 0);
+ snd_ac97_write_cache(ac97, AC97_3D_CONTROL, 0x0000);
+ err = snd_ctl_add(ac97->bus->card,
+ snd_ac97_cnew(&snd_ac97_ymf7x3_controls_speaker,
+ ac97));
+ if (err < 0)
+ return err;
+ snd_ac97_write_cache(ac97, AC97_YMF7X3_3D_MODE_SEL, 0x0c00);
+ return 0;
+}
+
+static const struct snd_kcontrol_new snd_ac97_yamaha_ymf743_controls_spdif[3] =
+{
+ AC97_SINGLE(SNDRV_CTL_NAME_IEC958("", PLAYBACK, SWITCH),
+ AC97_YMF7X3_DIT_CTRL, 0, 1, 0),
+ {
+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
+ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, NONE) "Source",
+ .info = snd_ac97_ymf7x3_spdif_source_info,
+ .get = snd_ac97_ymf7x3_spdif_source_get,
+ .put = snd_ac97_ymf7x3_spdif_source_put,
+ },
+ AC97_SINGLE(SNDRV_CTL_NAME_IEC958("", NONE, NONE) "Mute",
+ AC97_YMF7X3_DIT_CTRL, 2, 1, 1)
+};
+
+static int patch_yamaha_ymf743_build_spdif(struct snd_ac97 *ac97)
+{
+ int err;
+
+ err = patch_build_controls(ac97, &snd_ac97_controls_spdif[0], 3);
+ if (err < 0)
+ return err;
+ err = patch_build_controls(ac97,
+ snd_ac97_yamaha_ymf743_controls_spdif, 3);
+ if (err < 0)
+ return err;
+ /* set default PCM S/PDIF params */
+ /* PCM audio,no copyright,no preemphasis,PCM coder,original */
+ snd_ac97_write_cache(ac97, AC97_YMF7X3_DIT_CTRL, 0xa201);
+ return 0;
+}
+
+static struct snd_ac97_build_ops patch_yamaha_ymf743_ops = {
+ .build_spdif = patch_yamaha_ymf743_build_spdif,
+ .build_3d = patch_yamaha_ymf7x3_3d,
+};
+
+static int patch_yamaha_ymf743(struct snd_ac97 *ac97)
+{
+ ac97->build_ops = &patch_yamaha_ymf743_ops;
+ ac97->caps |= AC97_BC_BASS_TREBLE;
+ ac97->caps |= 0x04 << 10; /* Yamaha 3D enhancement */
+ ac97->rates[AC97_RATES_SPDIF] = SNDRV_PCM_RATE_48000; /* 48k only */
+ ac97->ext_id |= AC97_EI_SPDIF; /* force the detection of spdif */
+ return 0;
}
/* The AC'97 spec states that the S/PDIF signal is to be output at pin 48.
@@ -357,28 +426,6 @@ static const struct snd_kcontrol_new snd
AC97_SINGLE(SNDRV_CTL_NAME_IEC958("", NONE, NONE) "Mute",
AC97_YMF7X3_DIT_CTRL, 2, 1, 1)
};
-
-static int patch_yamaha_ymf7x3_3d(struct snd_ac97 *ac97)
-{
- struct snd_kcontrol *kctl;
- int err;
-
- kctl = snd_ac97_cnew(&snd_ac97_controls_3d[0], ac97);
- err = snd_ctl_add(ac97->bus->card, kctl);
- if (err < 0)
- return err;
- strcpy(kctl->id.name, "3D Control - Wide");
- kctl->private_value = AC97_SINGLE_VALUE(AC97_3D_CONTROL, 9, 7, 0);
- snd_ac97_write_cache(ac97, AC97_3D_CONTROL, 0x0000);
-
- err = snd_ctl_add(ac97->bus->card,
- snd_ac97_cnew(&snd_ac97_ymf7x3_controls_speaker,
- ac97));
- if (err < 0)
- return err;
- snd_ac97_write_cache(ac97, AC97_YMF7X3_3D_MODE_SEL, 0x0c00);
- return 0;
-}
static int patch_yamaha_ymf753_post_spdif(struct snd_ac97 * ac97)
{
diff -r a543470c3455 pci/ac97/ac97_proc.c
--- a/pci/ac97/ac97_proc.c Wed Sep 19 07:52:08 2007 +0900
+++ b/pci/ac97/ac97_proc.c Wed Sep 19 07:52:14 2007 +0900
@@ -236,10 +236,14 @@ static void snd_ac97_proc_read_main(stru
val = snd_ac97_read(ac97, AC97_PCM_MIC_ADC_RATE);
snd_iprintf(buffer, "PCM MIC ADC : %iHz\n", val);
}
- if ((ext & AC97_EI_SPDIF) || (ac97->flags & AC97_CS_SPDIF)) {
+ if ((ext & AC97_EI_SPDIF) || (ac97->flags & AC97_CS_SPDIF) ||
+ (ac97->id == AC97_ID_YMF743)) {
if (ac97->flags & AC97_CS_SPDIF)
val = snd_ac97_read(ac97, AC97_CSR_SPDIF);
- else
+ else if (ac97->id == AC97_ID_YMF743) {
+ val = snd_ac97_read(ac97, AC97_YMF7X3_DIT_CTRL);
+ val = 0x2000 | (val & 0xff00) >> 4 | (val & 0x38) >> 2;
+ } else
val = snd_ac97_read(ac97, AC97_SPDIF);
snd_iprintf(buffer, "SPDIF Control :%s%s%s%s Category=0x%x Generation=%i%s%s%s\n",
next prev parent reply other threads:[~2007-09-19 11:33 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-18 15:50 [PATCH 2/2] ac97: YMF743 missing controls support Keita Maehara
2007-09-18 16:04 ` Takashi Iwai
2007-09-18 23:47 ` Keita Maehara
2007-09-19 11:06 ` Takashi Iwai
2007-09-19 11:28 ` Keita Maehara
2007-09-19 11:34 ` Keita Maehara [this message]
2007-09-19 12:31 ` Takashi Iwai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87k5qmanxe.wl%maehara@debian.org \
--to=maehara@debian.org \
--cc=alsa-devel@alsa-project.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.