From: Jani Nikula <jani.nikula@intel.com>
To: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: [Intel-gfx] [PATCH] drm/i915/debugfs: remove i915_dpcd file
Date: Wed, 29 Jan 2020 14:06:56 +0200 [thread overview]
Message-ID: <87o8umbh5r.fsf@intel.com> (raw)
In-Reply-To: <20200129115738.GU13686@intel.com>
On Wed, 29 Jan 2020, Ville Syrjälä <ville.syrjala@linux.intel.com> wrote:
> On Fri, Jan 17, 2020 at 05:05:51PM +0200, Jani Nikula wrote:
>> We've long had the more generic /dev/drm_dp_auxN devices for the same
>> purpose. Drop the redundant and limited DPCD debugfs file.
>>
>> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
>
> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Thanks, pushed to dinq.
BR,
Jani.
>
>> ---
>> drivers/gpu/drm/i915/i915_debugfs.c | 64 -----------------------------
>> 1 file changed, 64 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/i915/i915_debugfs.c b/drivers/gpu/drm/i915/i915_debugfs.c
>> index c05fa4205de8..e320b957b792 100644
>> --- a/drivers/gpu/drm/i915/i915_debugfs.c
>> +++ b/drivers/gpu/drm/i915/i915_debugfs.c
>> @@ -4329,65 +4329,6 @@ int i915_debugfs_register(struct drm_i915_private *dev_priv)
>> minor->debugfs_root, minor);
>> }
>>
>> -struct dpcd_block {
>> - /* DPCD dump start address. */
>> - unsigned int offset;
>> - /* DPCD dump end address, inclusive. If unset, .size will be used. */
>> - unsigned int end;
>> - /* DPCD dump size. Used if .end is unset. If unset, defaults to 1. */
>> - size_t size;
>> - /* Only valid for eDP. */
>> - bool edp;
>> -};
>> -
>> -static const struct dpcd_block i915_dpcd_debug[] = {
>> - { .offset = DP_DPCD_REV, .size = DP_RECEIVER_CAP_SIZE },
>> - { .offset = DP_PSR_SUPPORT, .end = DP_PSR_CAPS },
>> - { .offset = DP_DOWNSTREAM_PORT_0, .size = 16 },
>> - { .offset = DP_LINK_BW_SET, .end = DP_EDP_CONFIGURATION_SET },
>> - { .offset = DP_SINK_COUNT, .end = DP_ADJUST_REQUEST_LANE2_3 },
>> - { .offset = DP_SET_POWER },
>> - { .offset = DP_EDP_DPCD_REV },
>> - { .offset = DP_EDP_GENERAL_CAP_1, .end = DP_EDP_GENERAL_CAP_3 },
>> - { .offset = DP_EDP_DISPLAY_CONTROL_REGISTER, .end = DP_EDP_BACKLIGHT_FREQ_CAP_MAX_LSB },
>> - { .offset = DP_EDP_DBC_MINIMUM_BRIGHTNESS_SET, .end = DP_EDP_DBC_MAXIMUM_BRIGHTNESS_SET },
>> -};
>> -
>> -static int i915_dpcd_show(struct seq_file *m, void *data)
>> -{
>> - struct drm_connector *connector = m->private;
>> - struct intel_dp *intel_dp =
>> - enc_to_intel_dp(intel_attached_encoder(to_intel_connector(connector)));
>> - u8 buf[16];
>> - ssize_t err;
>> - int i;
>> -
>> - if (connector->status != connector_status_connected)
>> - return -ENODEV;
>> -
>> - for (i = 0; i < ARRAY_SIZE(i915_dpcd_debug); i++) {
>> - const struct dpcd_block *b = &i915_dpcd_debug[i];
>> - size_t size = b->end ? b->end - b->offset + 1 : (b->size ?: 1);
>> -
>> - if (b->edp &&
>> - connector->connector_type != DRM_MODE_CONNECTOR_eDP)
>> - continue;
>> -
>> - /* low tech for now */
>> - if (WARN_ON(size > sizeof(buf)))
>> - continue;
>> -
>> - err = drm_dp_dpcd_read(&intel_dp->aux, b->offset, buf, size);
>> - if (err < 0)
>> - seq_printf(m, "%04x: ERROR %d\n", b->offset, (int)err);
>> - else
>> - seq_printf(m, "%04x: %*ph\n", b->offset, (int)err, buf);
>> - }
>> -
>> - return 0;
>> -}
>> -DEFINE_SHOW_ATTRIBUTE(i915_dpcd);
>> -
>> static int i915_panel_show(struct seq_file *m, void *data)
>> {
>> struct drm_connector *connector = m->private;
>> @@ -4552,11 +4493,6 @@ int i915_debugfs_connector_add(struct drm_connector *connector)
>> if (!root)
>> return -ENODEV;
>>
>> - if (connector->connector_type == DRM_MODE_CONNECTOR_DisplayPort ||
>> - connector->connector_type == DRM_MODE_CONNECTOR_eDP)
>> - debugfs_create_file("i915_dpcd", S_IRUGO, root,
>> - connector, &i915_dpcd_fops);
>> -
>> if (connector->connector_type == DRM_MODE_CONNECTOR_eDP) {
>> debugfs_create_file("i915_panel_timings", S_IRUGO, root,
>> connector, &i915_panel_fops);
>> --
>> 2.20.1
>>
>> _______________________________________________
>> Intel-gfx mailing list
>> Intel-gfx@lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
prev parent reply other threads:[~2020-01-29 12:07 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-17 15:05 [Intel-gfx] [PATCH] drm/i915/debugfs: remove i915_dpcd file Jani Nikula
2020-01-18 0:38 ` [Intel-gfx] ✓ Fi.CI.BAT: success for " Patchwork
2020-01-18 0:38 ` [Intel-gfx] ✗ Fi.CI.BUILD: warning " Patchwork
2020-01-20 18:51 ` [Intel-gfx] ✓ Fi.CI.IGT: success " Patchwork
2020-01-29 11:57 ` [Intel-gfx] [PATCH] " Ville Syrjälä
2020-01-29 12:06 ` Jani Nikula [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87o8umbh5r.fsf@intel.com \
--to=jani.nikula@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.