[PATCH 2/2] ARM64: dts: marvell: enable USB host on Armada-8040-DB

[gregory.clement@free-electrons.com (Gregory CLEMENT)]

Hi Miquel,
 
 On mer., ao?t 09 2017, Miquel Raynal <miquel.raynal@free-electrons.com> wrote:

> From: Grzegorz Jaszczyk <jaz@semihalf.com>
>
> Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
> following ports:
>   - host 0 and 1 of CPM
>   - host 0 of CPS
>
> These PHY are enabled by lanes coming from regulators based on two
> I2C expanders.
>
> Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>

Applied on mvebu/dt64

Thanks,

Gregory

> ---
>  arch/arm64/boot/dts/marvell/armada-8040-db.dts | 65 ++++++++++++++++++++++++++
>  1 file changed, 65 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> index 1e8f7242ed6f..0d7b2ae46610 100644
> --- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
> @@ -44,6 +44,7 @@
>   * Device Tree file for Marvell Armada 8040 Development board platform
>   */
>  
> +#include <dt-bindings/gpio/gpio.h>
>  #include "armada-8040.dtsi"
>  
>  / {
> @@ -59,6 +60,48 @@
>  		device_type = "memory";
>  		reg = <0x0 0x0 0x0 0x80000000>;
>  	};
> +
> +	cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "cpm-usb3h0-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "cpm-usb3h1-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	cpm_usb3_0_phy: cpm-usb3-0-phy {
> +		compatible = "usb-nop-xceiv";
> +		vcc-supply = <&cpm_reg_usb3_0_vbus>;
> +	};
> +
> +	cpm_usb3_1_phy: cpm-usb3-1-phy {
> +		compatible = "usb-nop-xceiv";
> +		vcc-supply = <&cpm_reg_usb3_1_vbus>;
> +	};
> +
> +	cps_reg_usb3_0_vbus: cps-usb3-0-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "cps-usb3h0-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&expander1 0 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	cps_usb3_0_phy: cps-usb3-0-phy {
> +		compatible = "usb-nop-xceiv";
> +		vcc-supply = <&cps_reg_usb3_0_vbus>;
> +	};
>  };
>  
>  &i2c0 {
> @@ -107,6 +150,25 @@
>  &cpm_i2c0 {
>  	status = "okay";
>  	clock-frequency = <100000>;
> +
> +	/* U31 */
> +	expander0: pca9555 at 21 {
> +		compatible = "nxp,pca9555";
> +		pinctrl-names = "default";
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		reg = <0x21>;
> +	};
> +
> +	/* U25 */
> +	expander1: pca9555 at 25 {
> +		compatible = "nxp,pca9555";
> +		pinctrl-names = "default";
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		reg = <0x25>;
> +	};
> +
>  };
>  
>  /* CON4 on CP0 expansion */
> @@ -116,11 +178,13 @@
>  
>  /* CON9 on CP0 expansion */
>  &cpm_usb3_0 {
> +	usb-phy = <&cpm_usb3_0_phy>;
>  	status = "okay";
>  };
>  
>  /* CON10 on CP0 expansion */
>  &cpm_usb3_1 {
> +	usb-phy = <&cpm_usb3_1_phy>;
>  	status = "okay";
>  };
>  
> @@ -159,6 +223,7 @@
>  
>  /* CON9 on CP1 expansion */
>  &cps_usb3_0 {
> +	usb-phy = <&cps_usb3_0_phy>;
>  	status = "okay";
>  };
>  
> -- 
> 2.11.0
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com