pxa27x_udc: Oops on probe with usb cable connected.

[robert.jarzmik@free.fr (Robert Jarzmik)]

Antonio Ospite <ospite@studenti.unina.it> writes:

>> Now, would you test the patch attached in this mail to see if :
>>  - it fixes your Oops
>>  - the UDC is usable after you attach a gadget driver to pxa27x_udc
>>
>
> The Oops does not occurr anymore but UDC does not work yet, with DEBUG
> disabled I see kernel stops here, no more messages _at_all_ after that:
> <6>[    7.196467] pxa27x_udc: version 2008-04-18
> <6>[    7.201653] pxa27x-udc pxa27x-udc: USB reset
>
> And on the host side I get:
> [ 6512.104045] usb 4-2: new full speed USB device using ohci_hcd and address 50
> [ 6512.512030] usb 4-2: device not accepting address 50, error -62
> [ 6512.512063] hub 4-0:1.0: unable to enumerate USB device on port 2
>
> If I enable debug back I can see some messages repeated over
> and over:
>
> <7>[   12.545381] pxa27x-udc pxa27x-udc: ep0:handle_ep0_ctrl_req: protocol STALL, udccsr0=0c1 err 1
> <7>[   12.554164] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=SETUP_STAGE->STALL, udccsr0=0x0c1, udcbcr=8
> <7>[   12.562987] pxa27x-udc pxa27x-udc: ep0:handle_ep0: state=STALL, req=(null), udccsr0=0x0c1, udcbcr=8, irq_msk=1
> <7>[   12.571818] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=STALL->SETUP_STAGE, udccsr0=0x0c1, udcbcr=8
> <7>[   12.580628] pxa27x-udc pxa27x-udc: ep0:handle_ep0_ctrl_req: protocol STALL, udccsr0=0c1 err 1
> <7>[   12.589416] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=SETUP_STAGE->STALL, udccsr0=0x0c1, udcbcr=8
> <7>[   12.598241] pxa27x-udc pxa27x-udc: ep0:handle_ep0: state=STALL, req=(null), udccsr0=0x0c1, udcbcr=8, irq_msk=1
> <7>[   12.607076] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=STALL->SETUP_STAGE, udccsr0=0x0c1, udcbcr=8
> <7>[   12.615890] pxa27x-udc pxa27x-udc: ep0:handle_ep0_ctrl_req: protocol STALL, udccsr0=0c1 err 1
> <7>[   12.624681] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=SETUP_STAGE->STALL, udccsr0=0x0c1, udcbcr=8
> <7>[   12.633513] pxa27x-udc pxa27x-udc: ep0:handle_ep0: state=STALL, req=(null), udccsr0=0x0c1, udcbcr=8, irq_msk=1
> <7>[   12.642354] pxa27x-udc pxa27x-udc: ep0:set_ep0state: state=STALL->SETUP_STAGE, udccsr0=0x0c1, udcbcr=8
That sequence prooves the patch works.
The patch purpose is to stall the control endpoint as long as no gadget driver
regitered itself and prevent the Oops.

What should be happening is that you didn't inserted one of the modules :
 - g_ether
 - or g_zero
 - or g_storage

Or, if you did, there is a sequence that somehow prevents the correct hook up
between the pxa27_udc and g_ether for instance. If you want to be convinced, add
a printk() at the beginning of usb_gadget_register_driver() in pxa27x_udc.c, and
you shall see that it is never called in your case.

That's pretty wierd, because as soon as g_ether is inserted, and because
pxa27x_udc was inserted before, the gadget layer calls the register function of
pxa27x_udc, which should link the gadget and the gadget driver.

> I noted that (either with or without this patch) a quite similar phone
> works, it's Motorola A1200 and has a different bootloader.
> Maybe comparing some registers can help here?
Mmmm. I would rather bet on modules order if I had to. Or some wierd sequence.

Do you have the possibility, in your boot sequence, in one of the init scripts,
to add :
modprobe pxa27x_udc
modprobe g_ether

And see what comes out of it ?

I'm afraid I'm a bit at a loss to investigate further, as I can't reproduce the
test case myself ... All I can think of is modules ordering ATM.

Cheers.

--
Robert