Re: [RFC v3 03/11] ath10k: per target configurablity of various items

[Kalle Valo <kvalo@codeaurora.org>]

Erik Stromdahl <erik.stromdahl@gmail.com> writes:

> On 2017-12-22 16:19, Kalle Valo wrote:
>
>> I was a bit torn about this, I definitely see the need for this but on
>> the other hand it creates duplicate data (for example two entries for
>> QCA9377 chip). I guess this is the right approach, at least I cannot
>> come up anything better.
>>
>> But this patch should be split into two:
>>
>> 1) add bus field to struct ath10k_hw_params
>>
>> 2) add max_num_peers field to struct ath10k_hw_params
>>
>> And it seems 2) is already implemented in commit 9f2992fea580 ("ath10k:
>> wmi: get wmi init parameter values from hw params"), so hopefully we
>> only need 1) anymore.
>>
>
> Before commit 9f2992fea580a48135591873e5e3ac7e01444207,
> TARGET_TLV_NUM_PEERS was used both in the WMI TLV init command
> and as the value of *max_num_peers* in *struct ath10k* (ar->max_num_peers).
>
> commit 9f2992fea580a48135591873e5e3ac7e01444207 does not set
> *ar->max_num_peers* to the value of *ar->hw_param->num_peers*.
>
> Is this correct?
>
> As I see it, there is a possible mismatch between what is written
> to the device in the WMI init message and the value of *ar->max_num_peers*.
>
> Do we still need *max_num_peers* in *struct ath10k* now that we have the
> *num_peers* member in *struct ath10k_hw_params*?

A good point, I didn't thought of that during review. No time to
investigate this right now, but maybe Rakesh and Govind (CCed) can
comment?

> I am currently rewriting my HL patches and I was thinking about adding
> a separate patch related to this.

Yeah, a separate patch to sort that out is a good idea.

>>> --- a/drivers/net/wireless/ath/ath10k/core.c
>>> +++ b/drivers/net/wireless/ath/ath10k/core.c
>>> @@ -1663,9 +1663,19 @@ static int ath10k_init_hw_params(struct ath10k *ar)
>>>   	for (i = 0; i < ARRAY_SIZE(ath10k_hw_params_list); i++) {
>>>   		hw_params = &ath10k_hw_params_list[i];
>>>   -		if (hw_params->id == ar->target_version &&
>>> -		    hw_params->dev_id == ar->dev_id)
>>> -			break;
>>> +		if (ar->is_high_latency) {
>>> +			/* High latency devices will use different fw depending
>>> +			 * on if it is a USB or SDIO device.
>>> +			 */
>>> +			if (hw_params->bus == ar->hif.bus &&
>>> +			    hw_params->id == ar->target_version &&
>>> +			    hw_params->dev_id == ar->dev_id)
>>> +				break;
>>> +		} else {
>>> +			if (hw_params->id == ar->target_version &&
>>> +			    hw_params->dev_id == ar->dev_id)
>>> +				break;
>>> +		}
>>
>> I don't like the is_high_latency test here at all. The bus field should
>> be checked with all entries, not just high latency ones. And because of
>> this even most of the hw_param bus field entries were not initialised.
>>
>> So only thing to do is to initialise the bus field for all the entries
>> and the ugly test here can be removed. Just remember that QCA4019 uses
>> AHB, I think all the rest is PCI. Or do we have AHB devices supported?
>
> I noticed that there has been introduced a new bus type (SNOC).
> Do you know which devices are SNOC devices?

SNOC is for wcn3990.

> Btw, what the heck is SNOC anyway?

I have forgetten already what the acronym meant but it's basically some
sort of shared memory communication method with the firmware.

-- 
Kalle Valo

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k