From: Kevin Hilman <khilman@deeprootsystems.com>
To: Koen Kooi <k.kooi@student.utwente.nl>
Cc: "linux-omap@vger.kernel.org List" <linux-omap@vger.kernel.org>
Subject: Re: new PM branch available
Date: Wed, 14 Jan 2009 14:14:13 -0800 [thread overview]
Message-ID: <87wscxk022.fsf@deeprootsystems.com> (raw)
In-Reply-To: <84166B96-7874-4B6D-B86E-659250F62558@student.utwente.nl> (Koen Kooi's message of "Wed\, 14 Jan 2009 08\:35\:30 +0100")
Koen Kooi <k.kooi@student.utwente.nl> writes:
> Op 13 jan 2009, om 22:51 heeft Kevin Hilman het volgende geschreven:
>
>> Hello,
>>
>> The latest PM branch is now available[1].
>>
>> I've done basic testing of retention and off-mode (suspend and dynamic
>> idle) on Beagle and custom HW. My SDP has something still keeping
>> CORE active that others have not seen, but I have yet to debug. Any
>> other reports from SDP testing would be appreciated.
>>
>> Notable changes/updates
>> - rebased on latest clock updates and fixes from Paul
>> - clockfw pre- and post- notifiers
>> - DVFS for VDD2
>
> The bootlog on my rev C1D beagle looks suspicious:
>
Hi Koen,
Hmm, it looks like you're tree is missing the McBSP fix from Paul[1].
This patch made it in before v2.6.28-omap1 which the latest PM branch
is based on, so I'm guessing you're not testing the latest PM branch.
Kevin
> Texas Instruments X-Loader 1.4.2 (Dec 3 2008 - 23:20:13)
> Reading boot sector
> Booting from mmc
>
>
> U-Boot 2009.01-rc1-00102-g8ecaab3 (Jan 10 2009 - 13:56:28)
>
> OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz
> OMAP3 Beagle board + LPDDR/NAND
> DRAM: 256 MB
> NAND: 256 MiB
> musb: using high speed
> In: serial
> Out: serial
> Err: serial
> Board revision: Cx
> Debug (GPIO6 datain): 0x04800000
> Hit any key to stop autoboot: 1 \b\b\b 0
> reading boot.scr
>
> ** Unable to read "boot.scr" from mmc 0:1 **
> reading uImage
>
> 2556572 bytes read
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Angstrom/2.6.28-pm1+gitrb5d11429
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 2556508 Bytes = 2.4 MB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
> OK
>
>
> Uncompressing Linux
> .................................................................................................................................................................... done
> , booting the kernel.
> Linux version 2.6.28-omap1 (koen@dominion) (gcc version 4.2.1) #1 Sun
> Jan 11 18:52:51 CET 2009
> CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
> Machine: OMAP3 Beagle Board
> Memory policy: ECC disabled, Data cache writeback
> On node 0 totalpages: 65536
> free_area_init_node: node 0, pgdat c050be14, node_mem_map c0540000
> Normal zone: 512 pages used for memmap
> Normal zone: 0 pages reserved
> Normal zone: 65024 pages, LIFO batch:15
> Movable zone: 0 pages used for memmap
> OMAP3430 ES3.0
> SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
> Built 1 zonelists in Zone order, mobility grouping on. Total pages:
> 65024
> Kernel command line: console=ttyS2,115200n8 video=omapfb:vram:2M,vram:
> 4M,mode:640x480@60 omapfb.debug=y omap-dss.debug=y loglevel=10
> omapfb.vram=4M,4M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
> Unknown boot option `omapfb.debug=y': ignoring
> Unknown boot option `omap-dss.debug=y': ignoring
> Unknown boot option `omapfb.vram=4M,4M': ignoring
> Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz
> GPMC revision 5.0
> IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
> Total of 96 interrupts on 1 active controller
> OMAP34xx GPIO hardware version 2.5
> PID hash table entries: 1024 (order: 10, 4096 bytes)
> OMAP clockevent source: GPTIMER12 at 32768 Hz
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 128MB = 256MB total
> Memory: 254336KB available (4712K code, 428K data, 188K init)
> Calibrating delay loop... 478.91 BogoMIPS (lpj=1867776)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> net_namespace: 532 bytes
> regulator: core version 0.5
> NET: Registered protocol family 16
> Found NAND on CS0
> Registering NAND on CS0
> ------------[ cut here ]------------
> WARNING: at arch/arm/mach-omap2/clock.c:1094 omap2_clk_register
> +0x24/0x3c()
> Modules linked in:
> [<c003b824>] (dump_stack+0x0/0x14) from [<c005b180>] (warn_on_slowpath
> +0x4c/0x68)
> [<c005b134>] (warn_on_slowpath+0x0/0x68) from [<c00416a8>]
> (omap2_clk_register+0x24/0x3c)
> r6:c04de968 r5:c04d82d8 r4:c04d8270
> [<c0041684>] (omap2_clk_register+0x0/0x3c) from [<c0048854>]
> (clk_register+0x44/0xc8)
> [<c0048810>] (clk_register+0x0/0xc8) from [<c00113ec>]
> (omap2_mcbsp_init+0xc8/0x130)
> r7:c0469ded r6:00000008 r5:c04d82d8 r4:c04d8270
> [<c0011324>] (omap2_mcbsp_init+0x0/0x130) from [<c00372d4>]
> (do_one_initcall+0x64/0x198)
> [<c0037270>] (do_one_initcall+0x0/0x198) from [<c0008718>]
> (kernel_init +0x70/0xdc)
> [<c00086a8>] (kernel_init+0x0/0xdc) from [<c005db54>] (do_exit
> +0x0/0x6b4)
> r5:00000000 r4:00000000
> ---[ end trace 1b75b31a2719ed1c ]---
> ------------[ cut here ]------------
> WARNING: at arch/arm/mach-omap2/clock.c:1094 omap2_clk_register
> +0x24/0x3c()
> Modules linked in:
> [<c003b824>] (dump_stack+0x0/0x14) from [<c005b180>] (warn_on_slowpath
> +0x4c/0x68)
> [<c005b134>] (warn_on_slowpath+0x0/0x68) from [<c00416a8>]
> (omap2_clk_register+0x24/0x3c)
> r6:c04de968 r5:c04d8340 r4:c04d82d8
> [<c0041684>] (omap2_clk_register+0x0/0x3c) from [<c0048854>]
> (clk_register+0x44/0xc8)
> [<c0048810>] (clk_register+0x0/0xc8) from [<c00113ec>]
> (omap2_mcbsp_init+0xc8/0x130)
> r7:c0469ded r6:00000008 r5:c04d8340 r4:c04d8270
> [<c0011324>] (omap2_mcbsp_init+0x0/0x130) from [<c00372d4>]
> (do_one_initcall+0x64/0x198)
> [<c0037270>] (do_one_initcall+0x0/0x198) from [<c0008718>]
> (kernel_init +0x70/0xdc)
> [<c00086a8>] (kernel_init+0x0/0xdc) from [<c005db54>] (do_exit
> +0x0/0x6b4)
> r5:00000000 r4:00000000
> ---[ end trace 1b75b31a2719ed1c ]---
> ------------[ cut here ]------------
> WARNING: at arch/arm/mach-omap2/clock.c:1094 omap2_clk_register
> +0x24/0x3c()
> Modules linked in:
> [<c003b824>] (dump_stack+0x0/0x14) from [<c005b180>] (warn_on_slowpath
> +0x4c/0x68)
> [<c005b134>] (warn_on_slowpath+0x0/0x68) from [<c00416a8>]
> (omap2_clk_register+0x24/0x3c)
> r6:c04de968 r5:c04d83a8 r4:c04d8340
> [<c0041684>] (omap2_clk_register+0x0/0x3c) from [<c0048854>]
> (clk_register+0x44/0xc8)
> [<c0048810>] (clk_register+0x0/0xc8) from [<c00113ec>]
> (omap2_mcbsp_init+0xc8/0x130)
> r7:c0469ded r6:00000008 r5:c04d83a8 r4:c04d8270
> [<c0011324>] (omap2_mcbsp_init+0x0/0x130) from [<c00372d4>]
> (do_one_initcall+0x64/0x198)
> [<c0037270>] (do_one_initcall+0x0/0x198) from [<c0008718>]
> (kernel_init +0x70/0xdc)
> [<c00086a8>] (kernel_init+0x0/0xdc) from [<c005db54>] (do_exit
> +0x0/0x6b4)
> r5:00000000 r4:00000000
> ---[ end trace 1b75b31a2719ed1c ]---
> ------------[ cut here ]------------
> WARNING: at arch/arm/mach-omap2/clock.c:1094 omap2_clk_register
> +0x24/0x3c()
> Modules linked in:
> [<c003b824>] (dump_stack+0x0/0x14) from [<c005b180>] (warn_on_slowpath
> +0x4c/0x68)
> [<c005b134>] (warn_on_slowpath+0x0/0x68) from [<c00416a8>]
> (omap2_clk_register+0x24/0x3c)
> r6:c04de968 r5:c04d8410 r4:c04d83a8
> [<c0041684>] (omap2_clk_register+0x0/0x3c) from [<c0048854>]
> (clk_register+0x44/0xc8)
> [<c0048810>] (clk_register+0x0/0xc8) from [<c00113ec>]
> (omap2_mcbsp_init+0xc8/0x130)
> r7:c0469ded r6:00000008 r5:c04d8410 r4:c04d8270
> [<c0011324>] (omap2_mcbsp_init+0x0/0x130) from [<c00372d4>]
> (do_one_initcall+0x64/0x198)
> [<c0037270>] (do_one_initcall+0x0/0x198) from [<c0008718>]
> (kernel_init +0x70/0xdc)
> [<c00086a8>] (kernel_init+0x0/0xdc) from [<c005db54>] (do_exit
> +0x0/0x6b4)
> r5:00000000 r4:00000000
> ---[ end trace 1b75b31a2719ed1c ]---
> ------------[ cut here ]------------
> WARNING: at arch/arm/mach-omap2/clock.c:1094 omap2_clk_register
> +0x24/0x3c()
> Modules linked in:
> [<c003b824>] (dump_stack+0x0/0x14) from [<c005b180>] (warn_on_slowpath
> +0x4c/0x68)
> [<c005b134>] (warn_on_slowpath+0x0/0x68) from [<c00416a8>]
> (omap2_clk_register+0x24/0x3c)
> r6:c04de968 r5:c04d8478 r4:c04d8410
> [<c0041684>] (omap2_clk_register+0x0/0x3c) from [<c0048854>]
> (clk_register+0x44/0xc8)
> [<c0048810>] (clk_register+0x0/0xc8) from [<c00113ec>]
> (omap2_mcbsp_init+0xc8/0x130)
> r7:c0469ded r6:00000008 r5:c04d8478 r4:c04d8270
> [<c0011324>] (omap2_mcbsp_init+0x0/0x130) from [<c00372d4>]
> (do_one_initcall+0x64/0x198)
> [<c0037270>] (do_one_initcall+0x0/0x198) from [<c0008718>]
> (kernel_init +0x70/0xdc)
> [<c00086a8>] (kernel_init+0x0/0xdc) from [<c005db54>] (do_exit
> +0x0/0x6b4)
> r5:00000000 r4:00000000
> ---[ end trace 1b75b31a2719ed1c ]---
> omap-mcbsp omap-mcbsp.1: Invalid clock configuration for McBSP1.
> omap-mcbsp: probe of omap-mcbsp.1 failed with error -2
> omap-mcbsp omap-mcbsp.2: Invalid clock configuration for McBSP2.
> omap-mcbsp: probe of omap-mcbsp.2 failed with error -2
> omap-mcbsp omap-mcbsp.3: Invalid clock configuration for McBSP3.
> omap-mcbsp: probe of omap-mcbsp.3 failed with error -2
> omap-mcbsp omap-mcbsp.4: Invalid clock configuration for McBSP4.
> omap-mcbsp: probe of omap-mcbsp.4 failed with error -2
> omap-mcbsp omap-mcbsp.5: Invalid clock configuration for McBSP5.
> omap-mcbsp: probe of omap-mcbsp.5 failed with error -2
> OMAP DMA hardware revision 4.0
> USB: No board-specific platform config found
> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
> twl4030: PIH (irq 7) chaining IRQs 368..375
> twl4030: power (irq 373) chaining IRQs 376..383
> twl4030: gpio (irq 368) chaining IRQs 384..401
> i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
> SCSI subsystem initialized
> twl4030_usb twl4030_usb: Initialized TWL4030 USB module
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
> musb_hdrc: ConfigData=0x33 (UTMI-16, HB-ISO Rx (X), SoftConn)
> musb_hdrc: MHDRC RTL version 1.400
> musb_core_init 1405: reconfigure software for static FIFOs
> musb_hdrc musb_hdrc: musb_init_controller failed with status -19
> regulator: VMMC1: 1850 <--> 3150 mV normal standby
> regulator: VDAC: 1800 mV normal standby
> regulator: VUSB1V5: 1500 mV normal standby
> regulator: VUSB1V8: 1800 mV normal standby
> regulator: VUSB3V1: 3100 mV normal standby
> regulator: VSIM: 1800 <--> 3000 mV normal standby
> Bluetooth: Core ver 2.13
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> cfg80211: Using static regulatory domain info
> cfg80211: Regulatory domain: US
> (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
> (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
> (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
> (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
> (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
> (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
> cfg80211: Calling CRDA for country: US
> NET: Registered protocol family 2
> Switched to high resolution mode on CPU 0
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> NET: Registered protocol family 1
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> msgmni has been set to 497
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Serial: 8250/16550 driver4 ports, IRQ sharing enabled
> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
> serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
> serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
> console [ttyS2] enabled
> brd: module loaded
> loop: module loaded
> usbcore: registered new interface driver asix
> usbcore: registered new interface driver cdc_ether
> usbcore: registered new interface driver rndis_host
> usbcore: registered new interface driver zd1211rw
> usbcore: registered new interface driver rndis_wlan
> usbcore: registered new interface driver zd1201
> usbcore: registered new interface driver usb8xxx
> usbcore: registered new interface driver rtl8187
> usbcore: registered new interface driver rt2500usb
> usbcore: registered new interface driver rt73usb
> usbcore: registered new interface driver p54usb
> i2c /dev entries driver
> input: triton2-pwrbutton as /class/input/input0
> triton2 power button driver initialized
> Driver 'sd' needs updating - please use bus_type methods
> Driver 'sr' needs updating - please use bus_type methods
> omap2-nand driver initializing
> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
> 1,8V 16-bit)
> cmdlinepart partition parsing not available
> Creating 5 MTD partitions on "omap2-nand":
> 0x00000000-0x00080000 : "X-Loader"
> 0x00080000-0x00260000 : "U-Boot"
> 0x00260000-0x00280000 : "U-Boot Env"
> 0x00280000-0x00680000 : "Kernel"
> 0x00680000-0x10000000 : "File System"
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> input: gpio-keys as /class/input/input1
> twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
> twl4030_rtc twl4030_rtc: Power up reset detected.
> twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> Bluetooth: HCI USB driver ver 2.10
> usbcore: registered new interface driver hci_usb
> Bluetooth: Broadcom Blutonium firmware driver ver 1.2
> usbcore: registered new interface driver bcm203x
> Bluetooth: Digianswer Bluetooth USB driver ver 0.10
> usbcore: registered new interface driver bpa10x
> Bluetooth: Generic Bluetooth SDIO driver ver 0.1
> cpuidle: using governor ladder
> cpuidle: using governor menu
> mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
> Registered led device: beagleboard::usr0
> Registered led device: beagleboard::usr1
> Registered led device: beagleboard::pmu_stat
> usbcore: registered new interface driver usbhid
> usbhid: v2.6:USB HID core driver
> Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
> usbcore: registered new interface driver snd-usb-audio
> ASoC version 0.13.2
> OMAP3 Beagle SoC init
> TWL4030 Audio Codec init
> asoc: twl4030 <-> omap-mcbsp-dai-(link_id) mapping ok
> ALSA device list:
> #0: omap3beagle (twl4030)
> oprofile: using arm/armv7
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> Bluetooth: L2CAP ver 2.11
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: SCO (Voice Link) ver 0.6
> Bluetooth: SCO socket layer initialized
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM ver 1.10
> Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> Bluetooth: BNEP filters: protocol multicast
> Bluetooth: HIDP (Human Interface Emulation) ver 1.2
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> ieee80211: 802.11 data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <jketreno@linux.intel.com
>>
> ieee80211_crypt: registered algorithm 'NULL'
> ieee80211_crypt: registered algorithm 'WEP'
> ieee80211_crypt: registered algorithm 'CCMP'
> ieee80211_crypt: registered algorithm 'TKIP'
> ThumbEE CPU extension supported.
> Power Management for TI OMAP3.
> pm_dbg_init()
> SmartReflex driver initialized
> Disabling unused clock "sr2_fck"
> Disabling unused clock "sr1_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "gpt2_ick"
> Disabling unused clock "gpt3_ick"
> Disabling unused clock "gpt4_ick"
> Disabling unused clock "gpt5_ick"
> Disabling unused clock "gpt6_ick"
> Disabling unused clock "gpt7_ick"
> Disabling unused clock "gpt8_ick"
> Disabling unused clock "gpt9_ick"
> Disabling unused clock "wdt3_ick"
> Disabling unused clock "wdt3_fck"
> Disabling unused clock "gpio2_dbck"
> Disabling unused clock "gpio3_dbck"
> Disabling unused clock "gpio4_dbck"
> Disabling unused clock "gpio5_dbck"
> Disabling unused clock "gpio6_dbck"
> Disabling unused clock "gpt9_fck"
> Disabling unused clock "gpt8_fck"
> Disabling unused clock "gpt7_fck"
> Disabling unused clock "gpt6_fck"
> Disabling unused clock "gpt5_fck"
> Disabling unused clock "gpt4_fck"
> Disabling unused clock "gpt3_fck"
> Disabling unused clock "gpt2_fck"
> Disabling unused clock "gpt1_ick"
> Disabling unused clock "wdt1_ick"
> Disabling unused clock "wdt2_ick"
> Disabling unused clock "wdt2_fck"
> Disabling unused clock "gpio1_dbck"
> Disabling unused clock "gpt1_fck"
> Disabling unused clock "cam_ick"
> Disabling unused clock "cam_mclk"
> Disabling unused clock "dss_ick"
> Disabling unused clock "dss_96m_fck"
> Disabling unused clock "dss1_alwon_fck"
> Disabling unused clock "des1_ick"
> Disabling unused clock "sha11_ick"
> Disabling unused clock "rng_ick"
> Disabling unused clock "aes1_ick"
> Disabling unused clock "ssi_ick"
> Disabling unused clock "mailboxes_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "gpt10_ick"
> Disabling unused clock "gpt11_ick"
> Disabling unused clock "i2c_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "hdq_ick"
> Disabling unused clock "mspro_ick"
> Disabling unused clock "des2_ick"
> Disabling unused clock "sha12_ick"
> Disabling unused clock "aes2_ick"
> Disabling unused clock "icr_ick"
> Disabling unused clock "pka_ick"
> Disabling unused clock "ssi_ssr_fck"
> Disabling unused clock "hdq_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "i2c_fck"
> Disabling unused clock "mspro_fck"
> Disabling unused clock "gpt11_fck"
> Disabling unused clock "gpt10_fck"
> Disabling unused clock "dpll4_m6x2_ck"
> Disabling unused clock "dpll4_m3x2_ck"
> Disabling unused clock "dpll3_m3x2_ck"
> Disabling unused clock "sys_clkout1"
> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
> twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00
> UTC (946684800)
> Waiting for root device /dev/mmcblk0p2...
> mmc0: new high speed SDHC card at address 8fe4
> mmcblk0: mmc0:8fe4 SD08G 7.40 GiB
> mmcblk0: p1 p2 p3
> EXT3-fs warning: maximal mount count reached, running e2fsck is
> recommended
> EXT3 FS on mmcblk0p2, internal journal
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem).
> Freeing init memory: 188K
> INIT: version 2.86 booting
> v/rules.d: time stamp 2009-01-13 21:05:30 is 285195917.614868154 s in
> the future
> udevd[596]: lookup_group: specified group 'scanner' unknown
>
> udevd[596]: lookup_group: specified group 'scanner' unknown
>
> udevd[596]: lookup_group: specified group 'scanner' unknown
>
> udevd[596]: lookup_group: specified group 'scanner' unknown
>
> udevd[596]: lookup_group: specified group 'nvram' unknown
>
> udevd[596]: lookup_user: specified user 'tss' unknown
>
> udevd[596]: lookup_group: specified group 'tss' unknown
>
> udevd[596]: lookup_group: specified group 'fuse' unknown
>
> udevd[596]: lookup_group: specified group 'kvm' unknown
>
> udevd[596]: lookup_group: specified group 'rdma' unknown
>
> udevd[596]: lookup_group: specified group 'rdma' unknown
>
> udevd[596]: lookup_group: specified group 'rdma' unknown
>
>
> Adding 160640k swap on /dev/mmcblk0p3. Priority:-1 extents:1 across:
> 160640k
> Remounting root file system...
> uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0
> Buffer I/O error on device mtdblock0, logical block 0
> end_request: I/O error, dev mtdblock0, sector 8
> Buffer I/O error on device mtdblock0, logical block 1
> uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector
> 16
> Buffer I/O error on device mtdblock0, logical block 2
> uncorrectable error : <3>uncorrectable error : <3>end_request: I/O
> error, dev mtdblock0, sector 24
> Buffer I/O error on device mtdblock0, logical block 3
> uncorrectable error : <3>end_request: I/O error, dev mtdblock0, sector 0
> Buffer I/O error on device mtdblock0, logical block 0
> WARNING: Couldn't open directory /lib/modules/2.6.28-omap1: No such
> file or directory
> FATAL: Could not open /lib/modules/2.6.28-omap1/modules.dep.temp for
> writing: No such file or directory
> modprobe: FATAL: Could not load /lib/modules/2.6.28-omap1/modules.dep:
> No such file or directory
>
> Setting up IP spoofing protection: rp_filter.
> Configuring network interfaces... modprobe: FATAL: Could not load
> /lib/ modules/2.6.28-omap1/modules.dep: No such file or directory
>
> eth0: unknown interface: No such device
> modprobe: FATAL: Could not load /lib/modules/2.6.28-omap1/modules.dep:
> No such file or directory
>
> modprobe: FATAL: Could not load /lib/modules/2.6.28-omap1/modules.dep:
> No such file or directory
>
> eth0 No such device
>
> modprobe: FATAL: Could not load /lib/modules/2.6.28-omap1/modules.dep:
> No such file or directory
>
> udhcpc: SIOCGIFINDEX: No such device
> done.
> Tue Jan 13 21:06:00 GMT 2009
> INIT: Entering runlevel: 5
> Configuring leds:
> beagleboard::pmu_st: none
> beagleboard::usr0: heartbeat
> beagleboard::usr1: mmc0
> ALSA: Restoring mixer settings...
>
> modprobe: FATAL: Could not load /lib/modules/2.6.28-omap1/modules.dep:
> No such file or directory
>
> dropbear.
> (failed.)
> [ ok ]
> Running ntpdate to synchronize clockError : Temporary failure in name
> resolution
> .
>
> .-------.
> | | .-.
> | | |-----.-----.-----.| | .----..-----.-----.
> | | | __ | ---'| '--.| .-'| | |
> | | | | | |--- || --'| | | ' | | | |
> '---'---'--'--'--. |-----''----''--' '-----'-'-'-'
> -' |
> '---'
>
> The Angstrom Distribution beagleboard ttyS2
>
> Angstrom 2009.X-test-20090102 beagleboard ttyS2
>
> beagleboard login: root
> root@beagleboard:~# ls /de\b\b\broot@beagleboard:~# ls /dev/fb\a\b
> \broot@beagleboard:~# ls /dev/full root@beagleboard:~# ls /dev/full
> pm-
> kernel
> root@beagleboard:~# find /sy\b\b\broot@beagleboard:~# find /sys/| grep CPU
> root@beagleboard:~# root@beagleboard:~# find /sys/| grep CPU\b \b\b
> \b\b \bpcu\b \b\b \b\b \bcpu
> /sys/devices/system/cpu
> /sys/devices/system/cpu/online
> /sys/devices/system/cpu/possible
> /sys/devices/system/cpu/present
> /sys/devices/system/cpu/cpuidle
> /sys/devices/system/cpu/cpuidle/current_driver
> /sys/devices/system/cpu/cpuidle/current_governor_ro
> /sys/devices/system/cpu/cpu0
> /sys/devices/system/cpu/cpu0/crash_notes
> /sys/devices/system/cpu/cpu0/cpuidle
> /sys/devices/system/cpu/cpu0/cpuidle/state0
> /sys/devices/system/cpu/cpu0/cpuidle/state0/name
> /sys/devices/system/cpu/cpu0/cpuidle/state0/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state0/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state0/power
> /sys/devices/system/cpu/cpu0/cpuidle/state0/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state0/time
> /sys/devices/system/cpu/cpu0/cpuidle/state1
> /sys/devices/system/cpu/cpu0/cpuidle/state1/name
> /sys/devices/system/cpu/cpu0/cpuidle/state1/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state1/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state1/power
> /sys/devices/system/cpu/cpu0/cpuidle/state1/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state1/time
> /sys/devices/system/cpu/cpu0/cpuidle/state2
> /sys/devices/system/cpu/cpu0/cpuidle/state2/name
> /sys/devices/system/cpu/cpu0/cpuidle/state2/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state2/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state2/power
> /sys/devices/system/cpu/cpu0/cpuidle/state2/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state2/time
> /sys/devices/system/cpu/cpu0/cpuidle/state3
> /sys/devices/system/cpu/cpu0/cpuidle/state3/name
> /sys/devices/system/cpu/cpu0/cpuidle/state3/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state3/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state3/power
> /sys/devices/system/cpu/cpu0/cpuidle/state3/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state3/time
> /sys/devices/system/cpu/cpu0/cpuidle/state4
> /sys/devices/system/cpu/cpu0/cpuidle/state4/name
> /sys/devices/system/cpu/cpu0/cpuidle/state4/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state4/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state4/power
> /sys/devices/system/cpu/cpu0/cpuidle/state4/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state4/time
> /sys/devices/system/cpu/cpu0/cpuidle/state5
> /sys/devices/system/cpu/cpu0/cpuidle/state5/name
> /sys/devices/system/cpu/cpu0/cpuidle/state5/desc
> /sys/devices/system/cpu/cpu0/cpuidle/state5/latency
> /sys/devices/system/cpu/cpu0/cpuidle/state5/power
> /sys/devices/system/cpu/cpu0/cpuidle/state5/usage
> /sys/devices/system/cpu/cpu0/cpuidle/state5/time
> /sys/class/misc/cpu_dma_latency
> /sys/class/misc/cpu_dma_latency/uevent
> /sys/class/misc/cpu_dma_latency/dev
> /sys/class/misc/cpu_dma_latency/subsystem
> /sys/class/misc/cpu_dma_latency/power
> /sys/class/misc/cpu_dma_latency/power/wakeup
> /sys/kernel/uids/0/cpu_share
> /sys/kernel/uids/1/cpu_share
> /sys/kernel/uids/46/cpu_share
> /sys/kernel/uids/47/cpu_share
> /sys/kernel/uids/42/cpu_share
> /sys/module/cpufreq
> /sys/module/cpufreq/parameters
> /sys/module/cpufreq/parameters/debug_ratelimit
> /sys/module/cpufreq/parameters/debug
> root@beagleboard:~# ls /sys/devices/system/cpu/cpu0/
> cpuidle crash_notes
> root@beagleboard:~# cd /me\b\b\broot@beagleboard:~# cd /media/
> mm\aroot@beagleboard:~# cd /media/mmcb\aroot@beagleboard:~# cd /media/
> mmcblk0p1root@beagleboard:~# cd /media/mmcblk0p1/
> root@beagleboard:/media/mmcblk0p1# ls
> broken picodlp-control_0.1-r1.1_armv7a.ipk uImage working
> mlo u-boot.bin untested
> root@beagleboard:/media/mmcblk0p1# cp wo\b\broot@beagleboard:/media/
> mmcblk0p1# cp working/uI\b \b\b
> \b2\aroot@beagleboard:/media/mmcblk0p1# cp working/2.6.2
> working/2.6.26 working/2.6.28-ehci
> working/2.6.27 working/2.6.28rc7
> root@beagleboard:/media/mmcblk0p1# cp working/2.6.2
> working/2.6.26 working/2.6.28-ehci
> working/2.6.27 working/2.6.28rc7
> root@beagleboard:/media/mmcblk0p1# cp working/2.6.28-
> eroot@beagleboard:/media/mmcblk0p1# cp working/2.6.28-ehci
> uI\b\broot@beagleboard:/media/mmcblk0p1# cp working/2.6.28-ehci uImage
> ; sync ; rebootred new interface driver cdc_ether
> usbcore: registered new interface driver rndis_host
> usbcore: registered new interface driver zd1211rw
> usbcore: registered new interface driver rndis_wlan
> usbcore: registered new interface driver zd1201
> usbcore: registered new interface driver usb8xxx
> usbcore: registered new interface driver rtl8187
> usbcore: registered new interface driver rt2500usb
> usbcore: registered new interface driver rt73usb
> usbcore: registered new interface driver p54usb
> i2c /dev entries driver
> input: triton2-pwrbutton as /class/input/input0
> triton2 power button driver initialized
> Driver 'sd' needs updating - please use bus_type methods
> Driver 'sr' needs updating - please use bus_type methods
> omap2-nand driver initializing
> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
> 1,8V 16-bit)
> cmdlinepart partition parsing not available
> Creating 5 MTD partitions on "omap2-nand":
> 0x00000000-0x00080000 : "X-Loader"
> 0x00080000-0x00260000 : "U-Boot"
> 0x00260000-0x00280000 : "U-Boot Env"
> 0x00280000-0x00680000 : "Kernel"
> 0x00680000-0x10000000 : "File System"
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> input: gpio-keys as /class/input/input1
> twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> Bluetooth: HCI USB driver ver 2.10
> usbcore: registered new interface driver hci_usb
> Bluetooth: Broadcom Blutonium firmware driver ver 1.2
> usbcore: registered new interface driver bcm203x
> Bluetooth: Digianswer Bluetooth USB driver ver 0.10
> usbcore: registered new interface driver bpa10x
> Bluetooth: Generic Bluetooth SDIO driver ver 0.1
> mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
> Registered led device: beagleboard::usr0
> Registered led device: beagleboard::usr1
> leds-gpio: probe of leds-gpio failed with error -22
> usbcore: registered new interface driver usbhid
> usbhid: v2.6:USB HID core driver
> Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
> usbcore: registered new interface driver snd-usb-audio
> ASoC version 0.13.2
> OMAP3 Beagle SoC init
> TWL4030 Audio Codec init
> asoc: twl4030 <-> omap-mcbsp-dai-(link_id) mapping ok
> ALSA device list:
> #0: omap3beagle (twl4030)
> oprofile: using arm/armv7
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> Bluetooth: L2CAP ver 2.11
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: SCO (Voice Link) ver 0.6
> Bluetooth: SCO socket layer initialized
> usb 1-2: new high speed USB device using ehci-omap and address 2
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> Bluetooth: RFCOMM ver 1.10
> Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> Bluetooth: BNEP filters: protocol multicast
> Bluetooth: HIDP (Human Interface Emulation) ver 1.2
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> ieee80211: 802.11 data/management/control stack, git-1.1.13
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <jketreno@linux.intel.com
>>
> ieee80211_crypt: registered algorithm 'NULL'
> ieee80211_crypt: registered algorithm 'WEP'
> ieee80211_crypt: registered algorithm 'CCMP'
> ieee80211_crypt: registered algorithm 'TKIP'
> ThumbEE CPU extension supported.
> Power Management for TI OMAP3.
> SmartReflex driver initialized
> Disabling unused clock "sr2_fck"
> Disabling unused clock "sr1_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "gpt2_ick"
> Disabling unused clock "gpt3_ick"
> Disabling unused clock "gpt4_ick"
> Disabling unused clock "gpt5_ick"
> Disabling unused clock "gpt6_ick"
> Disabling unused clock "gpt7_ick"
> Disabling unused clock "gpt8_ick"
> Disabling unused clock "gpt9_ick"
> Disabling unused clock "wdt3_ick"
> Disabling unused clock "wdt3_fck"
> Disabling unused clock "gpio2_dbck"
> Disabling unused clock "gpio3_dbck"
> Disabling unused clock "gpio4_dbck"
> Disabling unused clock "gpio5_dbck"
> Disabling unused clock "gpio6_dbck"
> Disabling unused clock "gpt9_fck"
> Disabling unused clock "gpt8_fck"
> Disabling unused clock "gpt7_fck"
> Disabling unused clock "gpt6_fck"
> Disabling unused clock "gpt5_fck"
> Disabling unused clock "gpt4_fck"
> Disabling unused clock "gpt3_fck"
> Disabling unused clock "gpt2_fck"
> Disabling unused clock "gpt1_ick"
> Disabling unused clock "wdt1_ick"
> Disabling unused clock "wdt2_ick"
> Disabling unused clock "wdt2_fck"
> Disabling unused clock "gpio1_dbck"
> Disabling unused clock "gpt1_fck"
> Disabling unused clock "cam_ick"
> Disabling unused clock "cam_mclk"
> Disabling unused clock "des1_ick"
> Disabling unused clock "sha11_ick"
> Disabling unused clock "rng_ick"
> Disabling unused clock "aes1_ick"
> Disabling unused clock "ssi_ick"
> Disabling unused clock "mailboxes_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "mcbsp_ick"
> Disabling unused clock "gpt10_ick"
> Disabling unused clock "gpt11_ick"
> Disabling unused clock "i2c_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "mcspi_ick"
> Disabling unused clock "hdq_ick"
> Disabling unused clock "mspro_ick"
> Disabling unused clock "des2_ick"
> Disabling unused clock "sha12_ick"
> Disabling unused clock "aes2_ick"
> Disabling unused clock "icr_ick"
> Disabling unused clock "pka_ick"
> Disabling unused clock "ssi_ssr_fck"
> Disabling unused clock "hdq_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcspi_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "mcbsp_fck"
> Disabling unused clock "i2c_fck"
> Disabling unused clock "mspro_fck"
> Disabling unused clock "gpt11_fck"
> Disabling unused clock "gpt10_fck"
> Disabling unused clock "iva2_ck"
> Disabling unused clock "dpll4_m6x2_ck"
> Disabling unused clock "dpll4_m5x2_ck"
> Disabling unused clock "dpll3_m3x2_ck"
> Disabling unused clock "sys_clkout1"
> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
> OMAPFB: omapfb_init
> OMAPFB: omapfb_probe
> OMAPFB: create 3 framebuffers
> OMAPFB: fb_infos allocated
> param '4M'
> param '4M'
> OMAPFB: allocating 4194304 bytes for fb 0
> OMAPFB: allocated VRAM paddr 80750000, vaddr d1000000
> OMAPFB: allocating 4194304 bytes for fb 1
> OMAPFB: allocated VRAM paddr 80b50000, vaddr d1400000
> OMAPFB: region0 phys 80750000 virt d1000000 size=4194304
> OMAPFB: region1 phys 80b50000 virt d1400000 size=4194304
> OMAPFB: region2 phys 00000000 virt 00000000 size=0
> OMAPFB: fbmems allocated
> OMAPFB: check_fb_var 0
> OMAPFB: xres = 640, yres = 480, vxres = 640, vyres = 480
> OMAPFB: set_fb_fix
> OMAPFB: check_fb_var 1
> OMAPFB: xres = 640, yres = 480, vxres = 640, vyres = 480
> OMAPFB: set_fb_fix
> OMAPFB: check_fb_var 2
> OMAPFB: set_fb_fix
> OMAPFB: fb_infos initialized
> OMAPFB: set_par(0)
> OMAPFB: set_fb_fix
> OMAPFB: apply_changes, fb 0, ovl 0
> OMAPFB: setup_overlay 0
> omap-dss DISPLAY: omap_dss_mgr_apply(lcd)
> omap-dss DISPC: dispc_enable_plane 0, 0
> omap-dss DISPC: dispc_enable_plane 1, 0
> omap-dss DISPC: dispc_enable_plane 2, 0
> omap-dss DSS: save context
> OMAPFB: pan_display(0)
> OMAPFB: setcmap
> OMAPFB: setcmap
> Console: switching to colour frame buffer device 80x30
> OMAPFB: pan_display(0)
> OMAPFB: setcmap
> OMAPFB: setcmap
> OMAPFB: framebuffers registered
> OMAPFB: apply_changes, fb 0, ovl 0
> OMAPFB: setup_overlay 0
> OMAPFB: apply_changes, fb 1, ovl 1
> OMAPFB: setup_overlay 1
> OMAPFB: apply_changes, fb 2, ovl 2
> OMAPFB: create_framebuffers done
> omap-dss DISPLAY: omap_dss_mgr_apply(lcd)
> omap-dss DISPC: dispc_setup_plane 0, 80750000, sw 640, 0,0, 640x480 ->
> 640x480, (ilace 0)
> omap-dss DISPC: dispc_enable_plane 0, 1
> omap-dss DISPC: dispc_enable_plane 1, 0
> omap-dss DISPC: dispc_enable_plane 2, 0
> omap-dss DSS: save context
> omap-dss DISPLAY: omap_dss_mgr_apply(tv)
> omap-dss DSS: save context
> omap-dss DISPLAY: omap_dss_mgr_apply_l4(l4)
> OMAPFB: mgr->apply'ed
> omap-dss DSI: PLL init
> omap-dss DISPC: dpll4_m4 = 432000000
> omap-dss DISPC: fck = 96000000 (9)
> omap-dss DISPC: lck = 96000000 (1)
> omap-dss DISPC: pck = 48000000 (2)
> clock: new_div = 9, new_rate = 48000000
> omap-dss DSI: PLL init done
> omap-dss DISPC: fifo(0) size 1024, low/high old 960/1023, new 256/960
> omap-dss DISPC: fifo(1) size 1024, low/high old 960/1023, new 256/960
> omap-dss DISPC: fifo(2) size 1024, low/high old 960/1023, new 256/960
> omap-dss DISPC: onoff 0 rf 0 ieo 0 ipc 0 ihs 0 ivs 0 acbi 0 acb 0
> omap-dss DSI: dsi_pll_calc
> omap-dss DSI: dsi_pll_program
> omap-dss DSI: DSI Fint 1857142
> omap-dss DSI: clkin (dss2_fck) rate 13000000, highfreq 0
> omap-dss DSI: DSIPHY = 2 * 329 / 7 * 13000000 / 1 = 1222000000
> omap-dss DSI: Data rate on 1 DSI lane 611 Mbps
> omap-dss DSI: Clock lane freq 305500000 Hz
> omap-dss DSI: regm3 = 13, dsi1_pll_fclk = 94000000
> omap-dss DSI: regm4 = 16, dsi2_pll_fclk = 76375000
> omap-dss DSI: PLL config done
> omap-dss DISPC: xres 640 yres 480
> omap-dss DISPC: pck 23500
> omap-dss DISPC: hsw 32 hfp 48 hbp 80 vsw 4 vfp 3 vbp 7
> omap-dss DISPC: hsync 29375Hz, vsync 59Hz
> OMAPFB: display->updated
> DISPC IRQ: 0x4024: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4024
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4000
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4000
> DISPC IRQ: 0x4022: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4022
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4000
> DISPC IRQ: 0x4022: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4022
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4000
> DISPC IRQ: 0x4022: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4022
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4000
> DISPC IRQ: 0x4002: SYNC_LOST
> omap-dss DISPC error: dispc irq error status 4002
> DISPC IRQ: 0x4020: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> OMAPFB: sysfs created
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4022: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: Excessive DISPC errors
> Turning off lcd and digit
> DISPC IRQ: 0x4022: SYNC_LOST
> omap-dss DISPC error: Excessive DISPC errors
> Turning off lcd and digit
> DISPC IRQ: 0x4000: SYNC_LOST
> omap-dss DISPC error: Excessive DISPC errors
> Turning off lcd and digit
> DISPC IRQ: 0x4003: SYNC_LOST
> omap-dss DISPC error: Excessive DISPC errors
> Turning off lcd and digit
> usb 1-2: configuration #1 chosen from 1 choice
> twl4030_rtc twl4030_rtc: setting system clock to 2009-01-13 21:11:13
> UTC (1231881073)
> hub 1-2:1.0: USB hub found
> hub 1-2:1.0: 4 ports detected
> mmc0: new SDHC card at address 8fe4
> mmcblk0: mmc0:8fe4 SD08G 7.40 GiB
> mmcblk0: p1 p2 p3
> EXT3-fs warning: maximal mount count reached, running e2fsck is
> recommended
> EXT3 FS on mmcblk0p2, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem).
> Freeing init memory: 188K
>
> If you have read till down here: still no cpufreq while the board file
> has the rate tables and the initcall:
>
> --- /tmp/board-omap3beagle.c 2009-01-12 15:46:26.000000000 +0100
> +++ git/arch/arm/mach-omap2/board-omap3beagle.c 2009-01-12
> 15:46:28.000000000 +0100
> @@ -41,14 +41,73 @@
> #include <mach/usb-ehci.h>
> #include <mach/common.h>
> #include <mach/gpmc.h>
> +#include <mach/omap-pm.h>
> #include <mach/nand.h>
> #include <mach/mux.h>
> #include <mach/omapfb.h>
> #include <mach/display.h>
> +#include <mach/clock.h>
> +
>
> #include "twl4030-generic-scripts.h"
> #include "mmc-twl4030.h"
> +#include "pm.h"
> +
> +/* MPU speeds */
> +#define S600M 600000000
> +#define S550M 550000000
> +#define S500M 500000000
> +#define S250M 250000000
> +#define S125M 125000000
> +
> +/* DSP speeds */
> +#define S430M 430000000
> +#define S400M 400000000
> +#define S360M 360000000
> +#define S180M 180000000
> +#define S90M 90000000
> +
> +/* L3 speeds */
> +#define S83M 83000000
> +#define S166M 166000000
> +
> +static struct omap_opp mpu_rate_table[] = {
> + {0, 0, 0},
> + /*OPP1*/
> + {S125M, VDD1_OPP1, 0x18},
> + /*OPP2*/
> + {S250M, VDD1_OPP2, 0x20},
> + /*OPP3*/
> + {S500M, VDD1_OPP3, 0x30},
> + /*OPP4*/
> + {S550M, VDD1_OPP4, 0x36},
> + /*OPP5*/
> + {S600M, VDD1_OPP5, 0x3C},
> +};
>
> +static struct omap_opp l3_rate_table[] = {
> + {0, 0, 0},
> + /*OPP1*/
> + {0, VDD2_OPP1, 0x18},
> + /*OPP2*/
> + {S83M, VDD2_OPP2, 0x20},
> + /*OPP3*/
> + {S166M, VDD2_OPP3, 0x2C},
> +};
> +
> +struct omap_opp dsp_rate_table[] = {
> + {0, 0, 0},
> + /*OPP1*/
> + {S90M, VDD1_OPP1, 0x18},
> + /*OPP2*/
> + {S180M, VDD1_OPP2, 0x20},
> + /*OPP3*/
> + {S360M, VDD1_OPP3, 0x30},
> + /*OPP4*/
> + {S400M, VDD1_OPP4, 0x36},
> + /*OPP5*/
> + {S430M, VDD1_OPP5, 0x3C},
> +};
>
> #define GPMC_CS0_BASE 0x60
> #define GPMC_CS_SIZE 0x30
>
> @@ -227,7 +294,8 @@
>
> static void __init omap3_beagle_init_irq(void)
> {
> - omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL, NULL, NULL);
> + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, mpu_rate_table,
> + dsp_rate_table, l3_rate_table);
> omap_init_irq();
> omap_gpio_init();
> }
>
>
> regards,
>
> Koen
[1] http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=818862e11bad091dc635baedace58265a126b5c8
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2009-01-14 22:14 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-13 21:51 new PM branch available Kevin Hilman
2009-01-14 7:35 ` Koen Kooi
2009-01-14 18:09 ` David Brownell
2009-01-14 22:14 ` Kevin Hilman [this message]
2009-01-15 8:18 ` Koen Kooi
2009-01-14 12:40 ` Ramesh Gupta Guntha
2009-01-14 16:35 ` Kevin Hilman
2009-01-14 13:57 ` Sriram V
2009-01-14 16:39 ` Kevin Hilman
2009-01-15 13:42 ` Premi, Sanjeev
2009-01-15 15:01 ` Kevin Hilman
2009-01-15 15:17 ` Premi, Sanjeev
2009-01-15 15:34 ` Kevin Hilman
2009-01-15 16:00 ` Premi, Sanjeev
2009-01-15 15:00 ` Sriram V
[not found] ` <8bf247760901150654n78b198f0o5c2270186e9c119e@mail.gmail.com>
2009-01-15 15:07 ` Kevin Hilman
2009-01-16 13:49 ` Nayak, Rajendra
2009-01-16 19:03 ` Kevin Hilman
2009-01-19 15:46 ` Premi, Sanjeev
2009-01-19 16:04 ` Premi, Sanjeev
2009-01-23 10:19 ` Nayak, Rajendra
2009-01-23 11:21 ` Högander Jouni
2009-01-23 12:00 ` Nayak, Rajendra
2009-01-23 12:10 ` Nayak, Rajendra
2009-01-23 16:49 ` Kevin Hilman
2009-01-23 12:10 ` Koen Kooi
2009-01-23 17:20 ` Kevin Hilman
2009-01-23 18:27 ` Koen Kooi
2009-01-23 17:48 ` Kevin Hilman
2009-01-27 9:18 ` Nayak, Rajendra
2009-02-02 17:45 ` Peter 'p2' De Schrijver
2009-02-02 19:42 ` Kevin Hilman
2009-02-02 20:06 ` Kevin Hilman
2009-02-04 0:52 ` Peter 'p2' De Schrijver
2009-02-04 16:04 ` Kevin Hilman
2009-02-04 16:15 ` Koen Kooi
2009-02-04 16:38 ` Peter 'p2' De Schrijver
-- strict thread matches above, loose matches on Subject: below --
2009-03-18 18:56 Nicholas Chen
2009-03-18 19:01 ` Kevin Hilman
2009-03-18 19:22 ` Nicholas Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87wscxk022.fsf@deeprootsystems.com \
--to=khilman@deeprootsystems.com \
--cc=k.kooi@student.utwente.nl \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.