Re: [PATCH v2] drm/msm: dpu: Allow planes to extend past active display

[Jeykumar Sankaran <jsanka@codeaurora.org>]

On 2018-08-28 13:50, Sean Paul wrote:
> From: Sean Paul <seanpaul@chromium.org>
> 
> The atomic_check is a bit too aggressive with respect to planes which
> leave the active area. This caused a bunch of log spew when the cursor
> got to the edge of the screen and stopped it from going all the way.
> 
> This patch removes the conservative bounds checks from atomic and clips
> the dst rect such that we properly display planes which go off the
> screen.
> 
> Changes in v2:
> - Apply the clip to src as well (taking into account scaling)
> 
> Cc: Sravanthi Kollukuduru <skolluku@codeaurora.org>
> Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
> Signed-off-by: Sean Paul <seanpaul@chromium.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c  |  3 +--
>  drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 14 +++++++++++++-
>  2 files changed, 14 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> index 07c2d15b45f2..f0a5e776ba32 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> @@ -1551,8 +1551,7 @@ static int dpu_crtc_atomic_check(struct drm_crtc
> *crtc,
>  		cnt++;
> 
>  		dst = drm_plane_state_dest(pstate);
> -		if (!drm_rect_intersect(&clip, &dst) ||
> -		    !drm_rect_equals(&clip, &dst)) {
> +		if (!drm_rect_intersect(&clip, &dst)) {
>  			DPU_ERROR("invalid vertical/horizontal
> destination\n");
>  			DPU_ERROR("display: " DRM_RECT_FMT " plane: "
>  				  DRM_RECT_FMT "\n",
> DRM_RECT_ARG(&crtc_rect),
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index efdf9b200dd9..adfd16625188 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -1254,7 +1254,8 @@ static int dpu_plane_sspp_atomic_update(struct
> drm_plane *plane,
>  	const struct dpu_format *fmt;
>  	struct drm_crtc *crtc;
>  	struct drm_framebuffer *fb;
> -	struct drm_rect src, dst;
> +	struct drm_rect clip = { 0 }, src, dst;
> +	int hscale, vscale;
> 
>  	if (!plane) {
>  		DPU_ERROR("invalid plane\n");
> @@ -1300,6 +1301,17 @@ static int dpu_plane_sspp_atomic_update(struct
> drm_plane *plane,
> 
>  	dst = drm_plane_state_dest(state);
> 
> +	hscale = drm_rect_calc_hscale(&src, &dst,
> +				      pdpu->pipe_sblk->maxupscale,
> +				      pdpu->pipe_sblk->maxdwnscale);
> +	vscale = drm_rect_calc_vscale(&src, &dst,
> +				      pdpu->pipe_sblk->maxupscale,
> +				      pdpu->pipe_sblk->maxdwnscale);
> +
> +	clip.x2 = crtc->state->adjusted_mode.hdisplay;
> +	clip.y2 = crtc->state->adjusted_mode.vdisplay;
> +	drm_rect_clip_scaled(&src, &dst, &clip, hscale, vscale);
> +
>  	DPU_DEBUG_PLANE(pdpu, "FB[%u] " DRM_RECT_FMT "->crtc%u "
> DRM_RECT_FMT
>  			", %4.4s ubwc %d\n", fb->base.id,
> DRM_RECT_ARG(&src),
>  			crtc->base.id, DRM_RECT_ARG(&dst),

Don't you have to update pdpu->pipe_cfg.src_rect and 
pdpu->pipe_cfg.dst_rect with clip?

-- 
Jeykumar S
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel