[U-Boot] [PATCH 01/13] mxc nand: Merge mtd and spl register definitions

["Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>]

This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.

Signed-off-by: Beno?t Th?baudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
---
 .../drivers/mtd/nand/mxc_nand.c                    |  247 ++++----------------
 .../include/fsl_nfc.h                              |   97 ++++----
 .../nand_spl/nand_boot_fsl_nfc.c                   |   58 ++---
 3 files changed, 128 insertions(+), 274 deletions(-)

diff --git u-boot-4d3c95f.orig/drivers/mtd/nand/mxc_nand.c u-boot-4d3c95f/drivers/mtd/nand/mxc_nand.c
index 936186f..9a9260c 100644
--- u-boot-4d3c95f.orig/drivers/mtd/nand/mxc_nand.c
+++ u-boot-4d3c95f/drivers/mtd/nand/mxc_nand.c
@@ -25,168 +25,23 @@
 #if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35)
 #include <asm/arch/imx-regs.h>
 #endif
+#include <fsl_nfc.h>
 
 #define DRIVER_NAME "mxc_nand"
 
-/*
- * TODO: Use same register defs here as nand_spl mxc nand driver.
- */
-/*
- * Register map and bit definitions for the Freescale NAND Flash Controller
- * present in various i.MX devices.
- *
- * MX31 and MX27 have version 1 which has
- * 	4 512 byte main buffers and
- * 	4 16 byte spare buffers
- * 	to support up to 2K byte pagesize nand.
- * 	Reading or writing a 2K page requires 4 FDI/FDO cycles.
- *
- * MX25 has version 1.1 which has
- * 	8 512 byte main buffers and
- * 	8 64 byte spare buffers
- * 	to support up to 4K byte pagesize nand.
- * 	Reading or writing a 2K or 4K page requires only 1 FDI/FDO cycle.
- *      Also some of registers are moved and/or changed meaning as seen below.
- */
-#if defined(CONFIG_MX31) || defined(CONFIG_MX27)
-#define MXC_NFC_V1
-#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
-#define MXC_NFC_V1_1
-#else
-#warning "MXC NFC version not defined"
-#endif
-
-#if defined(MXC_NFC_V1)
-#define NAND_MXC_NR_BUFS		4
-#define NAND_MXC_SPARE_BUF_SIZE		16
-#define NAND_MXC_REG_OFFSET		0xe00
-#define is_mxc_nfc_11() 		0
-#elif defined(MXC_NFC_V1_1)
-#define NAND_MXC_NR_BUFS		8
-#define NAND_MXC_SPARE_BUF_SIZE		64
-#define NAND_MXC_REG_OFFSET		0x1e00
-#define is_mxc_nfc_11() 		1
-#else
-#error "define CONFIG_NAND_MXC_VXXX to use mtd mxc nand driver"
-#endif
-struct nfc_regs {
-	uint8_t main_area[NAND_MXC_NR_BUFS][0x200];
-	uint8_t spare_area[NAND_MXC_NR_BUFS][NAND_MXC_SPARE_BUF_SIZE];
-	/*
-	 * reserved size is offset of nfc registers
-	 * minus total main and spare sizes
-	 */
-	uint8_t reserved1[NAND_MXC_REG_OFFSET
-		- NAND_MXC_NR_BUFS * (512 + NAND_MXC_SPARE_BUF_SIZE)];
-#if defined(MXC_NFC_V1)
-	uint16_t nfc_buf_size;
-	uint16_t reserved2;
-	uint16_t nfc_buf_addr;
-	uint16_t nfc_flash_addr;
-	uint16_t nfc_flash_cmd;
-	uint16_t nfc_config;
-	uint16_t nfc_ecc_status_result;
-	uint16_t nfc_rsltmain_area;
-	uint16_t nfc_rsltspare_area;
-	uint16_t nfc_wrprot;
-	uint16_t nfc_unlockstart_blkaddr;
-	uint16_t nfc_unlockend_blkaddr;
-	uint16_t nfc_nf_wrprst;
-	uint16_t nfc_config1;
-	uint16_t nfc_config2;
-#elif defined(MXC_NFC_V1_1)
-	uint16_t reserved2[2];
-	uint16_t nfc_buf_addr;
-	uint16_t nfc_flash_addr;
-	uint16_t nfc_flash_cmd;
-	uint16_t nfc_config;
-	uint16_t nfc_ecc_status_result;
-	uint16_t nfc_ecc_status_result2;
-	uint16_t nfc_spare_area_size;
-	uint16_t nfc_wrprot;
-	uint16_t reserved3[2];
-	uint16_t nfc_nf_wrprst;
-	uint16_t nfc_config1;
-	uint16_t nfc_config2;
-	uint16_t reserved4;
-	uint16_t nfc_unlockstart_blkaddr;
-	uint16_t nfc_unlockend_blkaddr;
-	uint16_t nfc_unlockstart_blkaddr1;
-	uint16_t nfc_unlockend_blkaddr1;
-	uint16_t nfc_unlockstart_blkaddr2;
-	uint16_t nfc_unlockend_blkaddr2;
-	uint16_t nfc_unlockstart_blkaddr3;
-	uint16_t nfc_unlockend_blkaddr3;
-#endif
-};
-
-/*
- * Set INT to 0, FCMD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Command operation
- */
-#define NFC_CMD            0x1
-
-/*
- * Set INT to 0, FADD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Address operation
- */
-#define NFC_ADDR           0x2
-
-/*
- * Set INT to 0, FDI to 1, rest to 0 in NFC_CONFIG2 Register
- * for Input operation
- */
-#define NFC_INPUT          0x4
-
-/*
- * Set INT to 0, FDO to 001, rest to 0 in NFC_CONFIG2 Register
- * for Data Output operation
- */
-#define NFC_OUTPUT         0x8
-
-/*
- * Set INT to 0, FD0 to 010, rest to 0 in NFC_CONFIG2 Register
- * for Read ID operation
- */
-#define NFC_ID             0x10
-
-/*
- * Set INT to 0, FDO to 100, rest to 0 in NFC_CONFIG2 Register
- * for Read Status operation
- */
-#define NFC_STATUS         0x20
-
-/*
- * Set INT to 1, rest to 0 in NFC_CONFIG2 Register for Read
- * Status operation
- */
-#define NFC_INT            0x8000
-
-#ifdef MXC_NFC_V1_1
-#define NFC_4_8N_ECC	(1 << 0)
-#else
-#define NFC_4_8N_ECC	0
-#endif
-#define NFC_SP_EN           (1 << 2)
-#define NFC_ECC_EN          (1 << 3)
-#define NFC_BIG             (1 << 5)
-#define NFC_RST             (1 << 6)
-#define NFC_CE              (1 << 7)
-#define NFC_ONE_CYCLE       (1 << 8)
-
 typedef enum {false, true} bool;
 
 struct mxc_nand_host {
-	struct mtd_info		mtd;
-	struct nand_chip	*nand;
-
-	struct nfc_regs __iomem	*regs;
-	int			spare_only;
-	int			status_request;
-	int			pagesize_2k;
-	int			clk_act;
-	uint16_t		col_addr;
-	unsigned int		page_addr;
+	struct mtd_info			mtd;
+	struct nand_chip		*nand;
+
+	struct fsl_nfc_regs __iomem	*regs;
+	int				spare_only;
+	int				status_request;
+	int				pagesize_2k;
+	int				clk_act;
+	uint16_t			col_addr;
+	unsigned int			page_addr;
 };
 
 static struct mxc_nand_host mxc_host;
@@ -304,10 +159,10 @@ static void wait_op_done(struct mxc_nand_host *host, int max_retries,
 	uint32_t tmp;
 
 	while (max_retries-- > 0) {
-		if (readw(&host->regs->nfc_config2) & NFC_INT) {
-			tmp = readw(&host->regs->nfc_config2);
+		if (readw(&host->regs->config2) & NFC_INT) {
+			tmp = readw(&host->regs->config2);
 			tmp  &= ~NFC_INT;
-			writew(tmp, &host->regs->nfc_config2);
+			writew(tmp, &host->regs->config2);
 			break;
 		}
 		udelay(1);
@@ -326,8 +181,8 @@ static void send_cmd(struct mxc_nand_host *host, uint16_t cmd)
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_cmd(host, 0x%x)\n", cmd);
 
-	writew(cmd, &host->regs->nfc_flash_cmd);
-	writew(NFC_CMD, &host->regs->nfc_config2);
+	writew(cmd, &host->regs->flash_cmd);
+	writew(NFC_CMD, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, cmd);
@@ -342,8 +197,8 @@ static void send_addr(struct mxc_nand_host *host, uint16_t addr)
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_addr(host, 0x%x)\n", addr);
 
-	writew(addr, &host->regs->nfc_flash_addr);
-	writew(NFC_ADDR, &host->regs->nfc_config2);
+	writew(addr, &host->regs->flash_addr);
+	writew(NFC_ADDR, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, addr);
@@ -375,19 +230,19 @@ static void send_prog_page(struct mxc_nand_host *host, uint8_t buf_id,
 		}
 	}
 
-	writew(buf_id, &host->regs->nfc_buf_addr);
+	writew(buf_id, &host->regs->buf_addr);
 
 	/* Configure spare or page+spare access */
 	if (!host->pagesize_2k) {
-		uint16_t config1 = readw(&host->regs->nfc_config1);
+		uint16_t config1 = readw(&host->regs->config1);
 		if (spare_only)
 			config1 |= NFC_SP_EN;
 		else
 			config1 &= ~(NFC_SP_EN);
-		writew(config1, &host->regs->nfc_config1);
+		writew(config1, &host->regs->config1);
 	}
 
-	writew(NFC_INPUT, &host->regs->nfc_config2);
+	writew(NFC_INPUT, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, spare_only);
@@ -402,19 +257,19 @@ static void send_read_page(struct mxc_nand_host *host, uint8_t buf_id,
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_read_page (%d)\n", spare_only);
 
-	writew(buf_id, &host->regs->nfc_buf_addr);
+	writew(buf_id, &host->regs->buf_addr);
 
 	/* Configure spare or page+spare access */
 	if (!host->pagesize_2k) {
-		uint32_t config1 = readw(&host->regs->nfc_config1);
+		uint32_t config1 = readw(&host->regs->config1);
 		if (spare_only)
 			config1 |= NFC_SP_EN;
 		else
 			config1 &= ~NFC_SP_EN;
-		writew(config1, &host->regs->nfc_config1);
+		writew(config1, &host->regs->config1);
 	}
 
-	writew(NFC_OUTPUT, &host->regs->nfc_config2);
+	writew(NFC_OUTPUT, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, spare_only);
@@ -442,14 +297,14 @@ static void send_read_id(struct mxc_nand_host *host)
 	uint16_t tmp;
 
 	/* NANDFC buffer 0 is used for device ID output */
-	writew(0x0, &host->regs->nfc_buf_addr);
+	writew(0x0, &host->regs->buf_addr);
 
 	/* Read ID into main buffer */
-	tmp = readw(&host->regs->nfc_config1);
+	tmp = readw(&host->regs->config1);
 	tmp &= ~NFC_SP_EN;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 
-	writew(NFC_ID, &host->regs->nfc_config2);
+	writew(NFC_ID, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, 0);
@@ -469,14 +324,14 @@ static uint16_t get_dev_status(struct mxc_nand_host *host)
 	/* store the main area1 first word, later do recovery */
 	store = readl(main_buf);
 	/* NANDFC buffer 1 is used for device status */
-	writew(1, &host->regs->nfc_buf_addr);
+	writew(1, &host->regs->buf_addr);
 
 	/* Read status into main buffer */
-	tmp = readw(&host->regs->nfc_config1);
+	tmp = readw(&host->regs->config1);
 	tmp &= ~NFC_SP_EN;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 
-	writew(NFC_STATUS, &host->regs->nfc_config2);
+	writew(NFC_STATUS, &host->regs->config2);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, 0);
@@ -515,13 +370,13 @@ static void _mxc_nand_enable_hwecc(struct mtd_info *mtd, int on)
 {
 	struct nand_chip *nand_chip = mtd->priv;
 	struct mxc_nand_host *host = nand_chip->priv;
-	uint16_t tmp = readw(&host->regs->nfc_config1);
+	uint16_t tmp = readw(&host->regs->config1);
 
 	if (on)
 		tmp |= NFC_ECC_EN;
 	else
 		tmp &= ~NFC_ECC_EN;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 }
 
 static int mxc_nand_read_oob_syndrome(struct mtd_info *mtd,
@@ -799,7 +654,7 @@ static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
 {
 	struct nand_chip *nand_chip = mtd->priv;
 	struct mxc_nand_host *host = nand_chip->priv;
-	uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+	uint16_t ecc_status = readw(&host->regs->ecc_status_result);
 	int subpages = mtd->writesize / nand_chip->subpagesize;
 	int pg2blk_shift = nand_chip->phys_erase_shift -
 			   nand_chip->page_shift;
@@ -845,7 +700,7 @@ static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
 	 * additional correction.  2-Bit errors cannot be corrected by
 	 * HW ECC, so we need to return failure
 	 */
-	uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+	uint16_t ecc_status = readw(&host->regs->ecc_status_result);
 
 	if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
 		MTDDEBUG(MTD_DEBUG_LEVEL0,
@@ -1289,14 +1144,14 @@ static void mxc_setup_config1(void)
 {
 	uint16_t tmp;
 
-	tmp = readw(&host->regs->nfc_config1);
+	tmp = readw(&host->regs->config1);
 	tmp |= NFC_ONE_CYCLE;
 	tmp |= NFC_4_8N_ECC;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 	if (host->pagesize_2k)
-		writew(64/2, &host->regs->nfc_spare_area_size);
+		writew(64/2, &host->regs->spare_area_size);
 	else
-		writew(16/2, &host->regs->nfc_spare_area_size);
+		writew(16/2, &host->regs->spare_area_size);
 }
 #else
 #define mxc_setup_config1()
@@ -1359,7 +1214,7 @@ int board_nand_init(struct nand_chip *this)
 	this->read_buf = mxc_nand_read_buf;
 	this->verify_buf = mxc_nand_verify_buf;
 
-	host->regs = (struct nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
+	host->regs = (struct fsl_nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
 	host->clk_act = 1;
 
 #ifdef CONFIG_MXC_NAND_HWECC
@@ -1383,15 +1238,15 @@ int board_nand_init(struct nand_chip *this)
 	host->pagesize_2k = 0;
 
 	this->ecc.size = 512;
-	tmp = readw(&host->regs->nfc_config1);
+	tmp = readw(&host->regs->config1);
 	tmp |= NFC_ECC_EN;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 #else
 	this->ecc.layout = &nand_soft_eccoob;
 	this->ecc.mode = NAND_ECC_SOFT;
-	tmp = readw(&host->regs->nfc_config1);
+	tmp = readw(&host->regs->config1);
 	tmp &= ~NFC_ECC_EN;
-	writew(tmp, &host->regs->nfc_config1);
+	writew(tmp, &host->regs->config1);
 #endif
 	/* Reset NAND */
 	this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
@@ -1400,10 +1255,10 @@ int board_nand_init(struct nand_chip *this)
 	 * preset operation
 	 * Unlock the internal RAM Buffer
 	 */
-	writew(0x2, &host->regs->nfc_config);
+	writew(0x2, &host->regs->config);
 
 	/* Blocks to be unlocked */
-	writew(0x0, &host->regs->nfc_unlockstart_blkaddr);
+	writew(0x0, &host->regs->unlockstart_blkaddr);
 	/* Originally (Freescale LTIB 2.6.21) 0x4000 was written to the
 	 * unlockend_blkaddr, but the magic 0x4000 does not always work
 	 * when writing more than some 32 megabytes (on 2k page nands)
@@ -1415,10 +1270,10 @@ int board_nand_init(struct nand_chip *this)
 	 * This might be NAND chip specific and the i.MX31 datasheet is
 	 * extremely vague about the semantics of this register.
 	 */
-	writew(0xFFFF, &host->regs->nfc_unlockend_blkaddr);
+	writew(0xFFFF, &host->regs->unlockend_blkaddr);
 
 	/* Unlock Block Command for given address range */
-	writew(0x4, &host->regs->nfc_wrprot);
+	writew(0x4, &host->regs->wrprot);
 
 	/* NAND bus width determines access functions used by upper layer */
 	if (is_16bit_nand())
diff --git u-boot-4d3c95f.orig/include/fsl_nfc.h u-boot-4d3c95f/include/fsl_nfc.h
index 279aaa5..6691e41 100644
--- u-boot-4d3c95f.orig/include/fsl_nfc.h
+++ u-boot-4d3c95f/include/fsl_nfc.h
@@ -24,28 +24,25 @@
 #define __FSL_NFC_H
 
 /*
- * TODO: Use same register defs for nand_spl mxc nand driver
- * and mtd mxc nand driver.
+ * Register map and bit definitions for the Freescale NAND Flash Controller
+ * present in various i.MX devices.
  *
- * Register map and bit definitions for the Freescale NAND Flash
- * Controller present in various i.MX devices.
+ * MX31 and MX27 have version 1, which has:
+ *	4 512-byte main buffers and
+ *	4 16-byte spare buffers
+ *	to support up to 2K byte pagesize nand.
+ *	Reading or writing a 2K page requires 4 FDI/FDO cycles.
  *
- * MX31 and MX27 have version 1 which has
- * 	4 512 byte main buffers and
- * 	4 16 byte spare buffers
- * 	to support up to 2K byte pagesize nand.
- * 	Reading or writing a 2K page requires 4 FDI/FDO cycles.
- *
- * MX25 has version 1.1 which has
- * 	8 512 byte main buffers and
- * 	8 64 byte spare buffers
- * 	to support up to 4K byte pagesize nand.
- * 	Reading or writing a 2K or 4K page requires only 1 FDI/FDO cycle.
- *      Also some of registers are moved and/or changed meaning as seen below.
+ * MX25 and MX35 have version 1.1, which has:
+ *	8 512-byte main buffers and
+ *	8 64-byte spare buffers
+ *	to support up to 4K byte pagesize nand.
+ *	Reading or writing a 2K or 4K page requires only 1 FDI/FDO cycle.
+ *	Also some of registers are moved and/or changed meaning as seen below.
  */
-#if defined(CONFIG_MX31) || defined(CONFIG_MX27)
+#if defined(CONFIG_MX27) || defined(CONFIG_MX31)
 #define MXC_NFC_V1
-#elif defined(CONFIG_MX25)
+#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
 #define MXC_NFC_V1_1
 #else
 #warning "MXC NFC version not defined"
@@ -55,18 +52,20 @@
 #define NAND_MXC_NR_BUFS		4
 #define NAND_MXC_SPARE_BUF_SIZE		16
 #define NAND_MXC_REG_OFFSET		0xe00
-#define NAND_MXC_2K_MULTI_CYCLE		1
+#define NAND_MXC_2K_MULTI_CYCLE
+#define is_mxc_nfc_11()			0
 #elif defined(MXC_NFC_V1_1)
 #define NAND_MXC_NR_BUFS		8
 #define NAND_MXC_SPARE_BUF_SIZE		64
 #define NAND_MXC_REG_OFFSET		0x1e00
+#define is_mxc_nfc_11()			1
 #else
-#error "define CONFIG_NAND_MXC_VXXX to use the mxc spl_nand driver"
+#error "define CONFIG_NAND_MXC_VXXX to use the mxc nand driver"
 #endif
 
 struct fsl_nfc_regs {
-	u32 main_area[NAND_MXC_NR_BUFS][512/4];
-	u32 spare_area[NAND_MXC_NR_BUFS][NAND_MXC_SPARE_BUF_SIZE/4];
+	u8 main_area[NAND_MXC_NR_BUFS][0x200];
+	u8 spare_area[NAND_MXC_NR_BUFS][NAND_MXC_SPARE_BUF_SIZE];
 	/*
 	 * reserved size is offset of nfc registers
 	 * minus total main and spare sizes
@@ -74,44 +73,44 @@ struct fsl_nfc_regs {
 	u8 reserved1[NAND_MXC_REG_OFFSET
 		- NAND_MXC_NR_BUFS * (512 + NAND_MXC_SPARE_BUF_SIZE)];
 #if defined(MXC_NFC_V1)
-	u16 bufsiz;
+	u16 buf_size;
 	u16 reserved2;
-	u16 buffer_address;
-	u16 flash_add;
+	u16 buf_addr;
+	u16 flash_addr;
 	u16 flash_cmd;
-	u16 configuration;
+	u16 config;
 	u16 ecc_status_result;
-	u16 ecc_rslt_main_area;
-	u16 ecc_rslt_spare_area;
-	u16 nf_wr_prot;
-	u16 unlock_start_blk_add;
-	u16 unlock_end_blk_add;
-	u16 nand_flash_wr_pr_st;
-	u16 nand_flash_config1;
-	u16 nand_flash_config2;
+	u16 rsltmain_area;
+	u16 rsltspare_area;
+	u16 wrprot;
+	u16 unlockstart_blkaddr;
+	u16 unlockend_blkaddr;
+	u16 nf_wrprst;
+	u16 config1;
+	u16 config2;
 #elif defined(MXC_NFC_V1_1)
 	u16 reserved2[2];
-	u16 buffer_address;
-	u16 flash_add;
+	u16 buf_addr;
+	u16 flash_addr;
 	u16 flash_cmd;
-	u16 configuration;
+	u16 config;
 	u16 ecc_status_result;
 	u16 ecc_status_result2;
 	u16 spare_area_size;
-	u16 nf_wr_prot;
+	u16 wrprot;
 	u16 reserved3[2];
-	u16 nand_flash_wr_pr_st;
-	u16 nand_flash_config1;
-	u16 nand_flash_config2;
+	u16 nf_wrprst;
+	u16 config1;
+	u16 config2;
 	u16 reserved4;
-	u16 unlock_start_blk_add0;
-	u16 unlock_end_blk_add0;
-	u16 unlock_start_blk_add1;
-	u16 unlock_end_blk_add1;
-	u16 unlock_start_blk_add2;
-	u16 unlock_end_blk_add2;
-	u16 unlock_start_blk_add3;
-	u16 unlock_end_blk_add3;
+	u16 unlockstart_blkaddr;
+	u16 unlockend_blkaddr;
+	u16 unlockstart_blkaddr1;
+	u16 unlockend_blkaddr1;
+	u16 unlockstart_blkaddr2;
+	u16 unlockend_blkaddr2;
+	u16 unlockstart_blkaddr3;
+	u16 unlockend_blkaddr3;
 #endif
 };
 
diff --git u-boot-4d3c95f.orig/nand_spl/nand_boot_fsl_nfc.c u-boot-4d3c95f/nand_spl/nand_boot_fsl_nfc.c
index d6b0d9b..f437deb 100644
--- u-boot-4d3c95f.orig/nand_spl/nand_boot_fsl_nfc.c
+++ u-boot-4d3c95f/nand_spl/nand_boot_fsl_nfc.c
@@ -36,13 +36,13 @@ static void nfc_wait_ready(void)
 {
 	uint32_t tmp;
 
-	while (!(readw(&nfc->nand_flash_config2) & NFC_INT))
+	while (!(readw(&nfc->config2) & NFC_INT))
 		;
 
 	/* Reset interrupt flag */
-	tmp = readw(&nfc->nand_flash_config2);
+	tmp = readw(&nfc->config2);
 	tmp &= ~NFC_INT;
-	writew(tmp, &nfc->nand_flash_config2);
+	writew(tmp, &nfc->config2);
 }
 
 void nfc_nand_init(void)
@@ -54,10 +54,10 @@ void nfc_nand_init(void)
 	writew(CONFIG_SYS_NAND_SPARE_SIZE / 2, &nfc->spare_area_size);
 
 	/* unlocking RAM Buff */
-	writew(0x2, &nfc->configuration);
+	writew(0x2, &nfc->config);
 
 	/* hardware ECC checking and correct */
-	config1 = readw(&nfc->nand_flash_config1) | NFC_ECC_EN | 0x800;
+	config1 = readw(&nfc->config1) | NFC_ECC_EN | 0x800;
 	/*
 	 * if spare size is larger that 16 bytes per 512 byte hunk
 	 * then use 8 symbol correction instead of 4
@@ -66,20 +66,20 @@ void nfc_nand_init(void)
 		config1 &= ~NFC_4_8N_ECC;
 	else
 		config1 |= NFC_4_8N_ECC;
-	writew(config1, &nfc->nand_flash_config1);
+	writew(config1, &nfc->config1);
 #elif defined(MXC_NFC_V1)
 	/* unlocking RAM Buff */
-	writew(0x2, &nfc->configuration);
+	writew(0x2, &nfc->config);
 
 	/* hardware ECC checking and correct */
-	writew(NFC_ECC_EN, &nfc->nand_flash_config1);
+	writew(NFC_ECC_EN, &nfc->config1);
 #endif
 }
 
 static void nfc_nand_command(unsigned short command)
 {
 	writew(command, &nfc->flash_cmd);
-	writew(NFC_CMD, &nfc->nand_flash_config2);
+	writew(NFC_CMD, &nfc->config2);
 	nfc_wait_ready();
 }
 
@@ -87,14 +87,14 @@ static void nfc_nand_page_address(unsigned int page_address)
 {
 	unsigned int page_count;
 
-	writew(0x00, &nfc->flash_add);
-	writew(NFC_ADDR, &nfc->nand_flash_config2);
+	writew(0x00, &nfc->flash_addr);
+	writew(NFC_ADDR, &nfc->config2);
 	nfc_wait_ready();
 
 	/* code only for large page flash */
 	if (CONFIG_SYS_NAND_PAGE_SIZE > 512) {
-		writew(0x00, &nfc->flash_add);
-		writew(NFC_ADDR, &nfc->nand_flash_config2);
+		writew(0x00, &nfc->flash_addr);
+		writew(NFC_ADDR, &nfc->config2);
 		nfc_wait_ready();
 	}
 
@@ -103,30 +103,30 @@ static void nfc_nand_page_address(unsigned int page_address)
 	if (page_address <= page_count) {
 		page_count--; /* transform 0x01000000 to 0x00ffffff */
 		do {
-			writew(page_address & 0xff, &nfc->flash_add);
-			writew(NFC_ADDR, &nfc->nand_flash_config2);
+			writew(page_address & 0xff, &nfc->flash_addr);
+			writew(NFC_ADDR, &nfc->config2);
 			nfc_wait_ready();
 			page_address = page_address >> 8;
 			page_count = page_count >> 8;
 		} while (page_count);
 	}
 
-	writew(0x00, &nfc->flash_add);
-	writew(NFC_ADDR, &nfc->nand_flash_config2);
+	writew(0x00, &nfc->flash_addr);
+	writew(NFC_ADDR, &nfc->config2);
 	nfc_wait_ready();
 }
 
 static void nfc_nand_data_output(void)
 {
-	int config1 = readw(&nfc->nand_flash_config1);
+	int config1 = readw(&nfc->config1);
 #ifdef NAND_MXC_2K_MULTI_CYCLE
 	int i;
 #endif
 
 	config1 |= NFC_ECC_EN | NFC_INT_MSK;
-	writew(config1, &nfc->nand_flash_config1);
-	writew(0, &nfc->buffer_address);
-	writew(NFC_OUTPUT, &nfc->nand_flash_config2);
+	writew(config1, &nfc->config1);
+	writew(0, &nfc->buf_addr);
+	writew(NFC_OUTPUT, &nfc->config2);
 	nfc_wait_ready();
 #ifdef NAND_MXC_2K_MULTI_CYCLE
 	/*
@@ -134,11 +134,11 @@ static void nfc_nand_data_output(void)
 	 * for pages larger than 512 bytes.
 	 */
 	for (i = 1; i < (CONFIG_SYS_NAND_PAGE_SIZE / 512); i++) {
-		config1 = readw(&nfc->nand_flash_config1);
+		config1 = readw(&nfc->config1);
 		config1 |= NFC_ECC_EN | NFC_INT_MSK;
-		writew(config1, &nfc->nand_flash_config1);
-		writew(i, &nfc->buffer_address);
-		writew(NFC_OUTPUT, &nfc->nand_flash_config2);
+		writew(config1, &nfc->config1);
+		writew(i, &nfc->buf_addr);
+		writew(NFC_OUTPUT, &nfc->config2);
 		nfc_wait_ready();
 	}
 #endif
@@ -155,7 +155,7 @@ static int nfc_read_page(unsigned int page_address, unsigned char *buf)
 	u32 *src;
 	u32 *dst;
 
-	writew(0, &nfc->buffer_address); /* read in first 0 buffer */
+	writew(0, &nfc->buf_addr); /* read in first 0 buffer */
 	nfc_nand_command(NAND_CMD_READ0);
 	nfc_nand_page_address(page_address);
 
@@ -167,7 +167,7 @@ static int nfc_read_page(unsigned int page_address, unsigned char *buf)
 	if (nfc_nand_check_ecc())
 		return -1;
 
-	src = &nfc->main_area[0][0];
+	src = (u32 *)&nfc->main_area[0][0];
 	dst = (u32 *)buf;
 
 	/* main copy loop from NAND-buffer to SDRAM memory */
@@ -188,7 +188,7 @@ static int is_badblock(int pagenumber)
 
 	/* Check the first two pages for bad block markers */
 	for (page = pagenumber; page < pagenumber + 2; page++) {
-		writew(0, &nfc->buffer_address); /* read in first 0 buffer */
+		writew(0, &nfc->buf_addr); /* read in first 0 buffer */
 		nfc_nand_command(NAND_CMD_READ0);
 		nfc_nand_page_address(page);
 
@@ -197,7 +197,7 @@ static int is_badblock(int pagenumber)
 
 		nfc_nand_data_output(); /* fill the main buffer 0 */
 
-		src = &nfc->spare_area[0][0];
+		src = (u32 *)&nfc->spare_area[0][0];
 
 		/*
 		 * IMPORTANT NOTE: The nand flash controller uses a non-