From: Edward Vidal <develone@sbcglobal.net>
To: "yocto@yoctoproject.org" <yocto@yoctoproject.org>,
"danielhilst@gmail.com" <danielhilst@gmail.com>
Subject: Re: wpa_supplicant on Raspberry Pi 2B
Date: Fri, 2 Oct 2015 21:37:56 +0000 (UTC) [thread overview]
Message-ID: <962916176.503077.1443821876374.JavaMail.yahoo@mail.yahoo.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 7704 bytes --]
Hi all,Still no success getting wifi working.Any and all help appreciated.
Created a new image which installed 46 new rpms linux-firmware see below.
ps -ax | grep wpa_supplicant
503 ? S 0:00 /usr/sbin/wpa_supplicant -u
704 pts/0 R+ 0:00 grep wpa_supplicant
root@raspberrypi2:~# wpa_cli stat
Failed to connect to non-global ctrl_ifname: (nil) error: Success
root@raspberrypi2:~# wpa_cli stat
Failed to connect to non-global ctrl_ifname: (nil) error: Success
root@raspberrypi2:~# wpa_supplicant -ddd -B -i wlan0 -D nl80211 -c /etc/wpa_supplicant.conf
wpa_supplicant v2.4
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'nl80211' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='0'
update_config=1
Line: 5 - start of a new network block
scan_ssid=1 (0x1)
ssid - hexdump_ascii(len=10):
41 54 54 39 78 32 78 39 6a 37 ATT9x2x9j7
PSK (ASCII passphrase) - hexdump_ascii(len=12): [REMOVED]
proto: 0x1
key_mgmt: 0x2
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='ATT9x2x9j7'
rfkill: initial event: idx=0 type=1 op=0 soft=1 hard=0
rfkill: WLAN soft blocked
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Using driver-based off-channel TX
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x5a6e68
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5a6e68 match=0505
nl80211: Could not yet enable interface 'wlan0' due to rfkill
netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
nl80211: driver param='(null)'
Add interface wlan0 to a new radio phy0
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 160 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: Added 802.11b mode based on 802.11g information
wlan0: Own MAC address: 40:a5:ef:05:4d:01
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
nl80211: set_key failed; err=-100 Network is down)
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
nl80211: set_key failed; err=-100 Network is down)
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
nl80211: set_key failed; err=-100 Network is down)
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
nl80211: set_key failed; err=-100 Network is down)
wlan0: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
wlan0: Setting scan request: 0.100000 sec
wlan0: WPS: UUID based on MAC address: 50fb4973-c5e3-5899-b3c0-27a64501d294
GnuTLS: Library version 3.3.14 (runtime) - 3.3.14 (build)
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Using existing control interface directory.
ctrl_interface_group=0
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
Daemonize..
root@raspberrypi2:~# wpa_cli stat
Selected interface 'wlan0'
wpa_state=INTERFACE_DISABLED
address=40:a5:ef:05:4d:01
uuid=50fb4973-c5e3-5899-b3c0-27a64501d294
root@raspberrypi2:~# ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 40:A5:EF:05:4D:01
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Thanks
+linux-firmware-0.0+git0+3161bfa479-r0.all
+linux-firmware-ar3k-0.0+git0+3161bfa479-r0.all
+linux-firmware-ar9170-0.0+git0+3161bfa479-r0.all
+linux-firmware-ath6k-0.0+git0+3161bfa479-r0.all
+linux-firmware-ath9k-0.0+git0+3161bfa479-r0.all
+linux-firmware-atheros-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-bcm4329-0.0+git0+3161bfa479-r0.all
+linux-firmware-bcm4330-0.0+git0+3161bfa479-r0.all
+linux-firmware-bcm4334-0.0+git0+3161bfa479-r0.all
+linux-firmware-broadcom-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-dev-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-135-6-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-3160-7-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-3160-8-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-3160-9-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6000-4-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6000g2a-5-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6000g2a-6-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6000g2b-5-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6000g2b-6-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6050-4-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-6050-5-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-7260-7-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-7260-8-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-7260-9-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-7265-8-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-7265-9-0.0+git0+3161bfa479-r0.all
+linux-firmware-iwlwifi-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-marvell-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-radeon-0.0+git0+3161bfa479-r0.all
+linux-firmware-radeon-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-ralink-0.0+git0+3161bfa479-r0.all
+linux-firmware-ralink-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-rtl-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-rtl8192ce-0.0+git0+3161bfa479-r0.all
+linux-firmware-rtl8192cu-0.0+git0+3161bfa479-r0.all
+linux-firmware-rtl8192su-0.0+git0+3161bfa479-r0.all
+linux-firmware-sd8686-0.0+git0+3161bfa479-r0.all
+linux-firmware-sd8787-0.0+git0+3161bfa479-r0.all
+linux-firmware-sd8797-0.0+git0+3161bfa479-r0.all
+linux-firmware-ti-connectivity-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-vt6656-0.0+git0+3161bfa479-r0.all
+linux-firmware-vt6656-license-0.0+git0+3161bfa479-r0.all
+linux-firmware-wl12xx-0.0+git0+3161bfa479-r0.all
+linux-firmware-wl18xx-0.0+git0+3161bfa479-r0.all
Edward Vidal Jr. e-mail develone@sbcglobal.net 915-595-1613
[-- Attachment #2: Type: text/html, Size: 16269 bytes --]
next reply other threads:[~2015-10-02 21:38 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-02 21:37 Edward Vidal [this message]
2015-10-03 16:50 ` wpa_supplicant on Raspberry Pi 2B Daniel.
[not found] <mailman.2882.1443798513.7199.yocto@yoctoproject.org>
2015-10-02 15:34 ` Edward Vidal
2015-10-02 18:18 ` Daniel.
[not found] ` <1533093975.464421.1443812908982.JavaMail.yahoo@mail.yahoo.com>
2015-10-02 19:50 ` Daniel.
-- strict thread matches above, loose matches on Subject: below --
2015-10-02 14:27 Edward Vidal
2015-10-02 14:56 ` Philip Balister
2015-10-02 15:08 ` Daniel.
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=962916176.503077.1443821876374.JavaMail.yahoo@mail.yahoo.com \
--to=develone@sbcglobal.net \
--cc=danielhilst@gmail.com \
--cc=yocto@yoctoproject.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.