All of lore.kernel.org
 help / color / mirror / Atom feed
From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
To: Alexandre Torgue <alexandre.torgue@foss.st.com>,
	Giuseppe Cavallaro <peppe.cavallaro@st.com>,
	Jose Abreu <Jose.Abreu@synopsys.com>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>,
	"David S. Miller" <davem@davemloft.net>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	Jakub Kicinski <kuba@kernel.org>,
	Jose Abreu <joabreu@synopsys.com>,
	linux-arm-kernel@lists.infradead.org,
	linux-stm32@st-md-mailman.stormreply.com, netdev@vger.kernel.org
Subject: [PATCH net-next 2/7] net: stmmac: convert to phylink_get_linkmodes()
Date: Tue, 25 Jan 2022 16:40:30 +0000	[thread overview]
Message-ID: <E1nCOru-005LSd-9d@rmk-PC.armlinux.org.uk> (raw)
In-Reply-To: <YfAnkuhiMoeFcVnb@shell.armlinux.org.uk>

Add the MAC speed, duplex and pause capabilities to the phylink_config
structure, and switch stmmac_validate() to use phylink_get_linkmodes()
to generate the mask of supported ethtool link modes.

Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL            Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 125 ++++++------------
 1 file changed, 42 insertions(+), 83 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 6708ca2aa4f7..e85ca75d394d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -942,95 +942,22 @@ static void stmmac_validate(struct phylink_config *config,
 {
 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mac_supported) = { 0, };
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
-	int tx_cnt = priv->plat->tx_queues_to_use;
-	int max_speed = priv->plat->max_speed;
-
-	phylink_set(mac_supported, 10baseT_Half);
-	phylink_set(mac_supported, 10baseT_Full);
-	phylink_set(mac_supported, 100baseT_Half);
-	phylink_set(mac_supported, 100baseT_Full);
-	phylink_set(mac_supported, 1000baseT_Half);
-	phylink_set(mac_supported, 1000baseT_Full);
-	phylink_set(mac_supported, 1000baseKX_Full);
 
+	/* This is very similar to phylink_generic_validate() except that
+	 * we always use PHY_INTERFACE_MODE_INTERNAL to get all capabilities.
+	 * This is because we don't always have config->supported_interfaces
+	 * populated (only when we have the XPCS.)
+	 *
+	 * When we do have an XPCS, we could pass state->interface, as XPCS
+	 * limits to a subset of the ethtool link modes allowed here.
+	 */
 	phylink_set(mac_supported, Autoneg);
-	phylink_set(mac_supported, Pause);
-	phylink_set(mac_supported, Asym_Pause);
 	phylink_set_port_modes(mac_supported);
-
-	/* Cut down 1G if asked to */
-	if ((max_speed > 0) && (max_speed < 1000)) {
-		phylink_set(mask, 1000baseT_Full);
-		phylink_set(mask, 1000baseX_Full);
-	} else if (priv->plat->has_gmac4) {
-		if (!max_speed || max_speed >= 2500) {
-			phylink_set(mac_supported, 2500baseT_Full);
-			phylink_set(mac_supported, 2500baseX_Full);
-		}
-	} else if (priv->plat->has_xgmac) {
-		if (!max_speed || (max_speed >= 2500)) {
-			phylink_set(mac_supported, 2500baseT_Full);
-			phylink_set(mac_supported, 2500baseX_Full);
-		}
-		if (!max_speed || (max_speed >= 5000)) {
-			phylink_set(mac_supported, 5000baseT_Full);
-		}
-		if (!max_speed || (max_speed >= 10000)) {
-			phylink_set(mac_supported, 10000baseSR_Full);
-			phylink_set(mac_supported, 10000baseLR_Full);
-			phylink_set(mac_supported, 10000baseER_Full);
-			phylink_set(mac_supported, 10000baseLRM_Full);
-			phylink_set(mac_supported, 10000baseT_Full);
-			phylink_set(mac_supported, 10000baseKX4_Full);
-			phylink_set(mac_supported, 10000baseKR_Full);
-		}
-		if (!max_speed || (max_speed >= 25000)) {
-			phylink_set(mac_supported, 25000baseCR_Full);
-			phylink_set(mac_supported, 25000baseKR_Full);
-			phylink_set(mac_supported, 25000baseSR_Full);
-		}
-		if (!max_speed || (max_speed >= 40000)) {
-			phylink_set(mac_supported, 40000baseKR4_Full);
-			phylink_set(mac_supported, 40000baseCR4_Full);
-			phylink_set(mac_supported, 40000baseSR4_Full);
-			phylink_set(mac_supported, 40000baseLR4_Full);
-		}
-		if (!max_speed || (max_speed >= 50000)) {
-			phylink_set(mac_supported, 50000baseCR2_Full);
-			phylink_set(mac_supported, 50000baseKR2_Full);
-			phylink_set(mac_supported, 50000baseSR2_Full);
-			phylink_set(mac_supported, 50000baseKR_Full);
-			phylink_set(mac_supported, 50000baseSR_Full);
-			phylink_set(mac_supported, 50000baseCR_Full);
-			phylink_set(mac_supported, 50000baseLR_ER_FR_Full);
-			phylink_set(mac_supported, 50000baseDR_Full);
-		}
-		if (!max_speed || (max_speed >= 100000)) {
-			phylink_set(mac_supported, 100000baseKR4_Full);
-			phylink_set(mac_supported, 100000baseSR4_Full);
-			phylink_set(mac_supported, 100000baseCR4_Full);
-			phylink_set(mac_supported, 100000baseLR4_ER4_Full);
-			phylink_set(mac_supported, 100000baseKR2_Full);
-			phylink_set(mac_supported, 100000baseSR2_Full);
-			phylink_set(mac_supported, 100000baseCR2_Full);
-			phylink_set(mac_supported, 100000baseLR2_ER2_FR2_Full);
-			phylink_set(mac_supported, 100000baseDR2_Full);
-		}
-	}
-
-	/* Half-Duplex can only work with single queue */
-	if (tx_cnt > 1) {
-		phylink_set(mask, 10baseT_Half);
-		phylink_set(mask, 100baseT_Half);
-		phylink_set(mask, 1000baseT_Half);
-	}
+	phylink_get_linkmodes(mac_supported, PHY_INTERFACE_MODE_INTERNAL,
+			      config->mac_capabilities);
 
 	linkmode_and(supported, supported, mac_supported);
-	linkmode_andnot(supported, supported, mask);
-
 	linkmode_and(state->advertising, state->advertising, mac_supported);
-	linkmode_andnot(state->advertising, state->advertising, mask);
 
 	/* If PCS is supported, check which modes it supports. */
 	if (priv->hw->xpcs)
@@ -1253,6 +1180,7 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 {
 	struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data;
 	struct fwnode_handle *fwnode = of_fwnode_handle(priv->plat->phylink_node);
+	int max_speed = priv->plat->max_speed;
 	int mode = priv->plat->phy_interface;
 	struct phylink *phylink;
 
@@ -1266,6 +1194,37 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 	if (!fwnode)
 		fwnode = dev_fwnode(priv->device);
 
+	priv->phylink_config.mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+		MAC_10 | MAC_100;
+
+	if (!max_speed || max_speed >= 1000)
+		priv->phylink_config.mac_capabilities |= MAC_1000;
+
+	if (priv->plat->has_gmac4) {
+		if (!max_speed || max_speed >= 2500)
+			priv->phylink_config.mac_capabilities |= MAC_2500FD;
+	} else if (priv->plat->has_xgmac) {
+		if (!max_speed || max_speed >= 2500)
+			priv->phylink_config.mac_capabilities |= MAC_2500FD;
+		if (!max_speed || max_speed >= 5000)
+			priv->phylink_config.mac_capabilities |= MAC_5000FD;
+		if (!max_speed || max_speed >= 10000)
+			priv->phylink_config.mac_capabilities |= MAC_10000FD;
+		if (!max_speed || max_speed >= 25000)
+			priv->phylink_config.mac_capabilities |= MAC_25000FD;
+		if (!max_speed || max_speed >= 40000)
+			priv->phylink_config.mac_capabilities |= MAC_40000FD;
+		if (!max_speed || max_speed >= 50000)
+			priv->phylink_config.mac_capabilities |= MAC_50000FD;
+		if (!max_speed || max_speed >= 100000)
+			priv->phylink_config.mac_capabilities |= MAC_100000FD;
+	}
+
+	/* Half-Duplex can only work with single queue */
+	if (priv->plat->tx_queues_to_use > 1)
+		priv->phylink_config.mac_capabilities &=
+			~(MAC_10HD | MAC_100HD | MAC_1000HD);
+
 	phylink = phylink_create(&priv->phylink_config, fwnode,
 				 mode, &stmmac_phylink_mac_ops);
 	if (IS_ERR(phylink))
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2022-01-25 16:42 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-01-25 16:38 [PATCH net-next 0/7] net: stmmac/xpcs: modernise PCS support Russell King (Oracle)
2022-01-25 16:40 ` [PATCH net-next 1/7] net: xpcs: add support for retrieving supported interface modes Russell King (Oracle)
2022-01-25 16:40 ` Russell King (Oracle) [this message]
2022-01-25 16:40 ` [PATCH net-next 3/7] net: stmmac: fill in supported_interfaces Russell King (Oracle)
2022-01-25 16:40 ` [PATCH net-next 4/7] net: stmmac/xpcs: convert to pcs_validate() Russell King (Oracle)
2022-01-25 18:53   ` Jakub Kicinski
2022-01-26  9:55     ` Russell King (Oracle)
2022-01-25 16:40 ` [PATCH net-next 5/7] net: stmmac: remove phylink_config.pcs_poll usage Russell King (Oracle)
2022-01-25 16:40 ` [PATCH net-next 6/7] net: stmmac: convert to phylink_generic_validate() Russell King (Oracle)
2022-01-25 16:40 ` [PATCH net-next 7/7] net: stmmac: use .mac_select_pcs() interface Russell King (Oracle)

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=E1nCOru-005LSd-9d@rmk-PC.armlinux.org.uk \
    --to=rmk+kernel@armlinux.org.uk \
    --cc=Jose.Abreu@synopsys.com \
    --cc=alexandre.torgue@foss.st.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=hkallweit1@gmail.com \
    --cc=joabreu@synopsys.com \
    --cc=kuba@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=mcoquelin.stm32@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=peppe.cavallaro@st.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.