From: Unknown <borg@uu3.net>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM: 2.4.36.1 hangs.
Date: Fri, 22 Feb 2008 15:08:30 +0100 (CET) [thread overview]
Message-ID: <Pine.LNX.4.64.0802221452350.5082@cube> (raw)
1) 2.4.36.1 hangs (probably during ext2_readdir())
2) 2.4.36.1 hangs during compilation of lighttpd-1.4.18.
It is probably during ext2_readdir() but I cannot confirm that..
Currently it only happens during compilation of lighttpd-1.4.18, always
in the same place.
Kernel 2.4.36 w/ same options (make oldconfig) works fine.
Last few lines of 'strace -f make' just before hang:
[pid 12817] open(".", O_RDONLY|O_NONBLOCK|O_LARGEFILE|O_DIRECTORY) = 3
[pid 12817] fstat64(3, {st_mode=S_IFDIR|0777, st_size=8192, ...}) = 0
[pid 12817] fcntl64(3, F_SETFD, FD_CLOEXEC) = 0
[pid 12817] getdents64(3, /* 114 entries */, 4096) = 4088
[pid 12817] getdents64(3, /* 63 entries */, 4096) = 2424
[pid 12817] getdents64(3,
3) ext2fs
4) None.
5) None. Kernel just hangs.
6)
cd /home/root/src/lighttpd-1.4.18
N=lighttpd
AP="/usr/local/$N"
EP="/usr/local"
ETC="/etc/$N"
./configure --prefix=$AP --bindir=$EP/bin --sbindir=$EP/sbin \
--libexecdir=$EP/libexec --mandir=$EP/man --sysconfdir=$ETC --disable-ipv6
make
7.1) Slackware-11.0
Linux darkstar 2.4.36.1 #2 Fri Feb 22 14:13:50 CET 2008 i686 pentium3 i386
GNU/Linux
Gnu C 3.4.6
Gnu make 3.81
binutils 2.15.92.0.2
util-linux 2.12r
mount 2.12r
modutils 2.4.27
e2fsprogs 1.38
Linux C Library 2.3.6
Dynamic linker (ldd) 2.3.6
Procps 3.2.7
Net-tools 1.60
Kbd 74:
Sh-utils 5.97
Modules Loaded
7.2)
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 10
cpu MHz : 930.329
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov
pat pse36 mmx fxsr sse
bogomips : 1854.66
7.3) None
7.4)
# cat /proc/ioports:
0000-001f : dma1
0020-003f : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
1000-100f : Intel Corp. 82801AA IDE
1000-1007 : ide0
1008-100f : ide1
1400-141f : Intel Corp. 82801AA USB
1800-180f : Intel Corp. 82801AA SMBus
2400-243f : Intel Corp. 82557/8/9 [Ethernet Pro 100]
2400-243f : eepro100
f000-f07f : motherboard
f000-f003 : PM1a_EVT_BLK
f004-f005 : PM1a_CNT_BLK
f008-f00b : PM_TMR
f028-f02b : GPE0_BLK
f02c-f02f : GPE1_BLK
f100-f10f : motherboard
f180-f1bf : motherboard
f800-f81f : motherboard
f820-f82f : motherboard
fe00-fe00 : motherboard
# cat /proc/iomem
00000000-0009ebff : System RAM
0009ec00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000c97ff : Extension ROM
000f0000-000fffff : System ROM
00100000-1feeffff : System RAM
00100000-0027773b : Kernel code
0027773c-002c52e3 : Kernel data
1fef0000-1fefefff : ACPI Tables
1feff000-1fefffff : ACPI Non-volatile Storage
1ff00000-1fffffff : reserved
f4000000-f407ffff : Intel Corp. 82810E DC-133 CGC [Chipset Graphics
Controller]
f4100000-f411ffff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
f4120000-f4120fff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
f4120000-f4120fff : eepro100
f8000000-fbffffff : Intel Corp. 82810E DC-133 CGC [Chipset Graphics
Controller]
ffb80000-ffbfffff : reserved
fff00000-ffffffff : reserved
7.5)
# lspci
00:00.0 Host bridge: Intel Corporation 82810E DC-133 GMCH [Graphics Memory
Controller Hub] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 CGC
[Chipset Graphics Controller] (rev 03) (prog-if 00 [VGA])
Subsystem: Siemens Nixdorf AG Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f4000000 (32-bit, non-prefetchable)
[size=512K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4100000-f41fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801AA IDE (rev 02) (prog-if 80
[Master])
Subsystem: Intel Corporation 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at 1000 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801AA USB (rev 02) (prog-if 00
[UHCI])
Subsystem: Intel Corporation 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1400 [size=32]
00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02)
Subsystem: Intel Corporation 82801AA SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1800 [size=16]
01:08.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro
100] (rev 09)
Subsystem: Siemens Nixdorf AG Unknown device 004b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f4120000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2400 [size=64]
Region 2: Memory at f4100000 (32-bit, non-prefetchable)
[size=128K]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
7.6) None
7.7) Box has been tested via memtest86+
15 hrs of test running, no errors
next reply other threads:[~2008-02-22 14:32 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-02-22 14:08 Unknown [this message]
2008-02-23 8:30 ` PROBLEM: 2.4.36.1 hangs Willy Tarreau
2008-02-24 18:12 ` Pascal Hambourg
2008-02-24 18:28 ` Willy Tarreau
2008-02-26 7:36 ` Glen Nakamura
2008-02-26 8:16 ` Willy Tarreau
2008-02-26 10:13 ` dann frazier
2008-02-26 10:27 ` Willy Tarreau
2008-02-26 13:54 ` Pascal Hambourg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.LNX.4.64.0802221452350.5082@cube \
--to=borg@uu3.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.