All of lore.kernel.org
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	linux-media@vger.kernel.org,
	Alexander Stein <alexander.stein@ew.tq-group.com>
Subject: Re: [PATCH v2 12/13] media: i2c: imx290: Add support for H & V Flips
Date: Tue, 7 Feb 2023 03:52:53 +0200	[thread overview]
Message-ID: <Y+Gu9aSaY8NJVCcs@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20230203191811.947697-13-dave.stevenson@raspberrypi.com>

Hi Dave,

Thank you for the patch.

On Fri, Feb 03, 2023 at 07:18:10PM +0000, Dave Stevenson wrote:
> The sensor supports H & V flips, so add the relevant hooks for
> V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
> 
> Note that the Bayer order is maintained as the readout area
> shifts by 1 pixel in the appropriate direction (note the
> comment about the top margin being 8 pixels whilst the bottom
> margin is 9). The V4L2_SEL_TGT_CROP region is therefore
> adjusted appropriately.
> 
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  drivers/media/i2c/imx290.c | 51 ++++++++++++++++++++++++++++++++++----
>  1 file changed, 46 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index 045d27b4d31b..7167eb1edb9b 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -208,6 +208,7 @@ struct imx290_mode {
>  	u32 hmax_min;
>  	u32 vmax_min;
>  	u8 link_freq_index;
> +	u8 ctrl_07;
>  
>  	const struct imx290_regval *data;
>  	u32 data_size;
> @@ -248,6 +249,10 @@ struct imx290 {
>  	struct v4l2_ctrl *hblank;
>  	struct v4l2_ctrl *vblank;
>  	struct v4l2_ctrl *exposure;
> +	struct {
> +		struct v4l2_ctrl *hflip;
> +		struct v4l2_ctrl *vflip;
> +	};
>  };
>  
>  static inline struct imx290 *to_imx290(struct v4l2_subdev *_sd)
> @@ -325,7 +330,6 @@ static const struct imx290_regval xclk_regs[][IMX290_NUM_CLK_REGS] = {
>  
>  static const struct imx290_regval imx290_1080p_settings[] = {
>  	/* mode settings */
> -	{ IMX290_CTRL_07, IMX290_WINMODE_1080P },
>  	{ IMX290_WINWV_OB, 12 },
>  	{ IMX290_OPB_SIZE_V, 10 },
>  	{ IMX290_X_OUT_SIZE, 1920 },
> @@ -334,7 +338,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
>  
>  static const struct imx290_regval imx290_720p_settings[] = {
>  	/* mode settings */
> -	{ IMX290_CTRL_07, IMX290_WINMODE_720P },
>  	{ IMX290_WINWV_OB, 6 },
>  	{ IMX290_OPB_SIZE_V, 4 },
>  	{ IMX290_X_OUT_SIZE, 1280 },
> @@ -494,6 +497,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
>  		.hmax_min = 2200,
>  		.vmax_min = 1125,
>  		.link_freq_index = FREQ_INDEX_1080P,
> +		.ctrl_07 = IMX290_WINMODE_1080P,
>  		.data = imx290_1080p_settings,
>  		.data_size = ARRAY_SIZE(imx290_1080p_settings),
>  		.clk_cfg = imx290_1080p_clock_config,
> @@ -504,6 +508,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
>  		.hmax_min = 3300,
>  		.vmax_min = 750,
>  		.link_freq_index = FREQ_INDEX_720P,
> +		.ctrl_07 = IMX290_WINMODE_720P,
>  		.data = imx290_720p_settings,
>  		.data_size = ARRAY_SIZE(imx290_720p_settings),
>  		.clk_cfg = imx290_720p_clock_config,
> @@ -517,6 +522,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
>  		.hmax_min = 2200,
>  		.vmax_min = 1125,
>  		.link_freq_index = FREQ_INDEX_1080P,
> +		.ctrl_07 = IMX290_WINMODE_1080P,
>  		.data = imx290_1080p_settings,
>  		.data_size = ARRAY_SIZE(imx290_1080p_settings),
>  		.clk_cfg = imx290_1080p_clock_config,
> @@ -527,6 +533,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
>  		.hmax_min = 3300,
>  		.vmax_min = 750,
>  		.link_freq_index = FREQ_INDEX_720P,
> +		.ctrl_07 = IMX290_WINMODE_720P,
>  		.data = imx290_720p_settings,
>  		.data_size = ARRAY_SIZE(imx290_720p_settings),
>  		.clk_cfg = imx290_720p_clock_config,
> @@ -835,6 +842,20 @@ static int imx290_set_ctrl(struct v4l2_ctrl *ctrl)
>  				   NULL);
>  		break;
>  
> +	case V4L2_CID_HFLIP:
> +	case V4L2_CID_VFLIP:
> +	{
> +		u32 reg;
> +
> +		reg = imx290->current_mode->ctrl_07;
> +		if (imx290->hflip->val)
> +			reg |= IMX290_HREVERSE;
> +		if (imx290->vflip->val)
> +			reg |= IMX290_VREVERSE;
> +		ret = imx290_write(imx290, IMX290_CTRL_07, reg, NULL);
> +		break;
> +	}
> +
>  	default:
>  		ret = -EINVAL;
>  		break;
> @@ -887,7 +908,7 @@ static int imx290_ctrl_init(struct imx290 *imx290)
>  	if (ret < 0)
>  		return ret;
>  
> -	v4l2_ctrl_handler_init(&imx290->ctrls, 9);
> +	v4l2_ctrl_handler_init(&imx290->ctrls, 11);
>  
>  	/*
>  	 * The sensor has an analog gain and a digital gain, both controlled
> @@ -944,6 +965,12 @@ static int imx290_ctrl_init(struct imx290 *imx290)
>  	imx290->vblank = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
>  					   V4L2_CID_VBLANK, 1, 1, 1, 1);
>  
> +	imx290->hflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> +					  V4L2_CID_HFLIP, 0, 1, 1, 0);
> +	imx290->vflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> +					  V4L2_CID_VFLIP, 0, 1, 1, 0);
> +	v4l2_ctrl_cluster(2, &imx290->hflip);
> +
>  	v4l2_ctrl_new_fwnode_properties(&imx290->ctrls, &imx290_ctrl_ops,
>  					&props);
>  
> @@ -1065,6 +1092,13 @@ static int imx290_set_stream(struct v4l2_subdev *sd, int enable)
>  		pm_runtime_put_autosuspend(imx290->dev);
>  	}
>  
> +	/*
> +	 * vflip and hflip should not be changed during streaming as the sensor
> +	 * will produce an invalid frame.
> +	 */
> +	__v4l2_ctrl_grab(imx290->vflip, enable);
> +	__v4l2_ctrl_grab(imx290->hflip, enable);
> +
>  unlock:
>  	v4l2_subdev_unlock_state(state);
>  	return ret;
> @@ -1147,16 +1181,23 @@ static int imx290_get_selection(struct v4l2_subdev *sd,
>  				struct v4l2_subdev_state *sd_state,
>  				struct v4l2_subdev_selection *sel)
>  {
> +	struct imx290 *imx290 = to_imx290(sd);
>  	struct v4l2_mbus_framefmt *format;
>  
>  	switch (sel->target) {
>  	case V4L2_SEL_TGT_CROP: {
>  		format = v4l2_subdev_get_pad_format(sd, sd_state, 0);
>  
> +		/*
> +		 * The sensor moves the readout by 1 pixel based on flips to
> +		 * keep the Bayer order the same.
> +		 */
>  		sel->r.top = IMX920_PIXEL_ARRAY_MARGIN_TOP
> -			   + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT - format->height) / 2;
> +			   + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT - format->height) / 2
> +			   + imx290->vflip->val;
>  		sel->r.left = IMX920_PIXEL_ARRAY_MARGIN_LEFT
> -			    + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH - format->width) / 2;
> +			    + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH - format->width) / 2
> +			    + imx290->hflip->val;
>  		sel->r.width = format->width;
>  		sel->r.height = format->height;
>  

-- 
Regards,

Laurent Pinchart

  reply	other threads:[~2023-02-07  1:53 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-02-03 19:17 [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Dave Stevenson
2023-02-03 19:17 ` [PATCH v2 01/13] media: i2c: imx290: Match kernel coding style on whitespace Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 02/13] media: i2c: imx290: Set the colorspace fields in the format Dave Stevenson
2023-02-07  1:34   ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 03/13] media: i2c: imx290: Add V4L2_SUBDEV_FL_HAS_EVENTS and subscribe hooks Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 04/13] media: i2c: imx290: Fix the pixel rate at 148.5Mpix/s Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 05/13] media: i2c: imx290: Support 60fps in 2 lane operation Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 06/13] media: i2c: imx290: Use CSI timings as per datasheet Dave Stevenson
2023-02-06  7:48   ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 07/13] media: i2c: imx290: Convert V4L2_CID_HBLANK to read/write Dave Stevenson
2023-02-06  7:59   ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 08/13] media: i2c: imx290: Convert V4L2_CID_VBLANK " Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 09/13] media: i2c: imx290: VMAX is mode dependent Dave Stevenson
2023-02-07  1:46   ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 10/13] media: i2c: imx290: Remove duplicated write to IMX290_CTRL_07 Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 11/13] media: i2c: imx290: Add support for 74.25MHz external clock Dave Stevenson
2023-02-06  8:24   ` Alexander Stein
2023-02-07  1:50   ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 12/13] media: i2c: imx290: Add support for H & V Flips Dave Stevenson
2023-02-07  1:52   ` Laurent Pinchart [this message]
2023-02-03 19:18 ` [PATCH v2 13/13] media: i2c: imx290: Add the error code to logs in start_streaming Dave Stevenson
2023-02-06  8:27   ` Alexander Stein
2023-02-07  1:53   ` Laurent Pinchart
2023-02-07  1:55 ` [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Laurent Pinchart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=Y+Gu9aSaY8NJVCcs@pendragon.ideasonboard.com \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=alexander.stein@ew.tq-group.com \
    --cc=dave.stevenson@raspberrypi.com \
    --cc=linux-media@vger.kernel.org \
    --cc=mani@kernel.org \
    --cc=mchehab@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.