From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Ricardo Ribalda <ribalda@chromium.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-kernel@vger.kernel.org, Tomasz Figa <tfiga@chromium.org>,
linux-media@vger.kernel.org
Subject: Re: [PATCH v1 3/3] media: uvcvideo: Do power management granularly
Date: Tue, 25 Oct 2022 15:45:36 +0300 [thread overview]
Message-ID: <Y1facEGMo+N1v0RU@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20220920-resend-powersave-v1-3-123aa2ba3836@chromium.org>
Hi Ricardo,
Thank you for the patch.
On Tue, Sep 20, 2022 at 04:09:52PM +0200, Ricardo Ribalda wrote:
> Instead of suspending/resume the USB device at open()/close(), do it
> when the device is actually used.
>
> This way we can reduce the power consumption when a service is holding
> the video device and leaving it in an idle state.
>
> Reviewed-by: Tomasz Figa <tfiga@chromium.org>
> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
>
> diff --git a/drivers/media/usb/uvc/uvc_v4l2.c b/drivers/media/usb/uvc/uvc_v4l2.c
> index 8d5002543e2c..b9642afabd9b 100644
> --- a/drivers/media/usb/uvc/uvc_v4l2.c
> +++ b/drivers/media/usb/uvc/uvc_v4l2.c
> @@ -25,6 +25,46 @@
>
> #include "uvcvideo.h"
>
> +/* ------------------------------------------------------------------------
> + * UVC power management
> + */
> +
> +static int uvc_pm_get(struct uvc_streaming *stream)
> +{
> + int ret = 0;
No need to initialize ret to 0.
> +
> + ret = usb_autopm_get_interface(stream->dev->intf);
> + if (ret)
> + return ret;
> +
> + mutex_lock(&stream->dev->lock);
> + if (!stream->dev->users)
> + ret = uvc_status_start(stream->dev, GFP_KERNEL);
For devices that don't have a status endpoint, we will end up calling
uvc_status_start() and uvc_status_stop() around most ioctl calls (all
call sites of uvc_pm_get() and uvc_pm_put() below). uvc_status_start()
and uvc_status_stop() are no-op in that case, but conceptually I don't
think that's very nice. Could we instead keep the status start/stop
calls to open()/release() ?
If you don't mind, I'll give this a try and post a new version of the
patch, that should be faster than going through another review round.
> + if (!ret)
> + stream->dev->users++;
> + mutex_unlock(&stream->dev->lock);
> +
> + if (ret)
> + usb_autopm_put_interface(stream->dev->intf);
> +
> + return ret;
> +}
> +
> +static void uvc_pm_put(struct uvc_streaming *stream)
> +{
> + mutex_lock(&stream->dev->lock);
> + if (WARN_ON(!stream->dev->users)) {
> + mutex_unlock(&stream->dev->lock);
> + return;
> + }
> + stream->dev->users--;
> + if (!stream->dev->users)
> + uvc_status_stop(stream->dev);
> + mutex_unlock(&stream->dev->lock);
> +
> + usb_autopm_put_interface(stream->dev->intf);
> +}
> +
> /* ------------------------------------------------------------------------
> * UVC ioctls
> */
> @@ -249,6 +289,9 @@ static int uvc_v4l2_try_format(struct uvc_streaming *stream,
> * developers test their webcams with the Linux driver as well as with
> * the Windows driver).
> */
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> mutex_lock(&stream->mutex);
> if (stream->dev->quirks & UVC_QUIRK_PROBE_EXTRAFIELDS)
> probe->dwMaxVideoFrameSize =
> @@ -257,6 +300,7 @@ static int uvc_v4l2_try_format(struct uvc_streaming *stream,
> /* Probe the device. */
> ret = uvc_probe_video(stream, probe);
> mutex_unlock(&stream->mutex);
> + uvc_pm_put(stream);
> if (ret < 0)
> return ret;
>
> @@ -468,7 +512,13 @@ static int uvc_v4l2_set_streamparm(struct uvc_streaming *stream,
> }
>
> /* Probe the device with the new settings. */
> + ret = uvc_pm_get(stream);
> + if (ret) {
> + mutex_unlock(&stream->mutex);
> + return ret;
> + }
> ret = uvc_probe_video(stream, &probe);
> + uvc_pm_put(stream);
> if (ret < 0) {
> mutex_unlock(&stream->mutex);
> return ret;
> @@ -559,36 +609,29 @@ static int uvc_v4l2_open(struct file *file)
> {
> struct uvc_streaming *stream;
> struct uvc_fh *handle;
> - int ret = 0;
>
> stream = video_drvdata(file);
> uvc_dbg(stream->dev, CALLS, "%s\n", __func__);
>
> - ret = usb_autopm_get_interface(stream->dev->intf);
> - if (ret < 0)
> - return ret;
> -
> /* Create the device handle. */
> handle = kzalloc(sizeof(*handle), GFP_KERNEL);
> - if (handle == NULL) {
> - usb_autopm_put_interface(stream->dev->intf);
> + if (!handle)
> return -ENOMEM;
> - }
>
> - mutex_lock(&stream->dev->lock);
> - if (stream->dev->users == 0) {
> - ret = uvc_status_start(stream->dev, GFP_KERNEL);
> - if (ret < 0) {
> - mutex_unlock(&stream->dev->lock);
> - usb_autopm_put_interface(stream->dev->intf);
> + /*
> + * If the uvc evdev exists we cannot suspend when the device
> + * is idle. Otherwise we will miss button actions.
> + */
> + if (stream->dev->input) {
> + int ret;
> +
> + ret = uvc_pm_get(stream);
> + if (ret) {
> kfree(handle);
> return ret;
> }
> }
>
> - stream->dev->users++;
> - mutex_unlock(&stream->dev->lock);
> -
> v4l2_fh_init(&handle->vfh, &stream->vdev);
> v4l2_fh_add(&handle->vfh);
> handle->chain = stream->chain;
> @@ -610,6 +653,12 @@ static int uvc_v4l2_release(struct file *file)
> if (uvc_has_privileges(handle))
> uvc_queue_release(&stream->queue);
>
> + if (handle->is_streaming)
> + uvc_pm_put(stream);
> +
> + if (stream->dev->input)
> + uvc_pm_put(stream);
> +
> /* Release the file handle. */
> uvc_dismiss_privileges(handle);
> v4l2_fh_del(&handle->vfh);
> @@ -617,12 +666,6 @@ static int uvc_v4l2_release(struct file *file)
> kfree(handle);
> file->private_data = NULL;
>
> - mutex_lock(&stream->dev->lock);
> - if (--stream->dev->users == 0)
> - uvc_status_stop(stream->dev);
> - mutex_unlock(&stream->dev->lock);
> -
> - usb_autopm_put_interface(stream->dev->intf);
> return 0;
> }
>
> @@ -849,9 +892,17 @@ static int uvc_ioctl_streamon(struct file *file, void *fh,
>
> if (handle->is_streaming)
> goto unlock;
> +
> + ret = uvc_pm_get(stream);
> + if (ret)
> + goto unlock;
> +
> ret = uvc_queue_streamon(&stream->queue, type);
> handle->is_streaming = !ret;
>
> + if (!handle->is_streaming)
> + uvc_pm_put(stream);
> +
> unlock:
> mutex_unlock(&stream->mutex);
>
> @@ -875,6 +926,9 @@ static int uvc_ioctl_streamoff(struct file *file, void *fh,
> ret = uvc_queue_streamoff(&stream->queue, type);
> handle->is_streaming = !!ret;
>
> + if (!handle->is_streaming)
> + uvc_pm_put(stream);
> +
> unlock:
> mutex_unlock(&stream->mutex);
>
> @@ -928,6 +982,7 @@ static int uvc_ioctl_g_input(struct file *file, void *fh, unsigned int *input)
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> u8 *buf;
> int ret;
>
> @@ -941,9 +996,16 @@ static int uvc_ioctl_g_input(struct file *file, void *fh, unsigned int *input)
> if (!buf)
> return -ENOMEM;
>
> + ret = uvc_pm_get(stream);
> + if (ret) {
> + kfree(buf);
> + return ret;
> + }
> +
> ret = uvc_query_ctrl(chain->dev, UVC_GET_CUR, chain->selector->id,
> chain->dev->intfnum, UVC_SU_INPUT_SELECT_CONTROL,
> buf, 1);
> + uvc_pm_put(stream);
> if (!ret)
> *input = *buf - 1;
>
> @@ -956,6 +1018,7 @@ static int uvc_ioctl_s_input(struct file *file, void *fh, unsigned int input)
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> u8 *buf;
> int ret;
>
> @@ -977,10 +1040,17 @@ static int uvc_ioctl_s_input(struct file *file, void *fh, unsigned int input)
> if (!buf)
> return -ENOMEM;
>
> + ret = uvc_pm_get(stream);
> + if (ret) {
> + kfree(buf);
> + return ret;
> + }
> +
> *buf = input + 1;
> ret = uvc_query_ctrl(chain->dev, UVC_SET_CUR, chain->selector->id,
> chain->dev->intfnum, UVC_SU_INPUT_SELECT_CONTROL,
> buf, 1);
> + uvc_pm_put(stream);
> kfree(buf);
>
> return ret;
> @@ -991,8 +1061,15 @@ static int uvc_ioctl_queryctrl(struct file *file, void *fh,
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> + int ret;
>
> - return uvc_query_v4l2_ctrl(chain, qc);
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> + ret = uvc_query_v4l2_ctrl(chain, qc);
> + uvc_pm_put(stream);
> + return ret;
> }
>
> static int uvc_ioctl_query_ext_ctrl(struct file *file, void *fh,
> @@ -1000,10 +1077,15 @@ static int uvc_ioctl_query_ext_ctrl(struct file *file, void *fh,
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> struct v4l2_queryctrl qc = { qec->id };
> int ret;
>
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> ret = uvc_query_v4l2_ctrl(chain, &qc);
> + uvc_pm_put(stream);
> if (ret)
> return ret;
>
> @@ -1049,6 +1131,7 @@ static int uvc_ioctl_g_ext_ctrls(struct file *file, void *fh,
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> struct v4l2_ext_control *ctrl = ctrls->controls;
> unsigned int i;
> int ret;
> @@ -1073,22 +1156,30 @@ static int uvc_ioctl_g_ext_ctrls(struct file *file, void *fh,
> return 0;
> }
>
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> ret = uvc_ctrl_begin(chain);
> - if (ret < 0)
> + if (ret < 0) {
> + uvc_pm_put(stream);
> return ret;
> + }
>
> for (i = 0; i < ctrls->count; ++ctrl, ++i) {
> ret = uvc_ctrl_get(chain, ctrl);
> if (ret < 0) {
> uvc_ctrl_rollback(handle);
> ctrls->error_idx = i;
> - return ret;
> + goto done;
> }
> }
>
> ctrls->error_idx = 0;
>
> - return uvc_ctrl_rollback(handle);
> + ret = uvc_ctrl_rollback(handle);
> +done:
> + uvc_pm_put(stream);
> + return ret;
> }
>
> static int uvc_ioctl_s_try_ext_ctrls(struct uvc_fh *handle,
> @@ -1097,6 +1188,7 @@ static int uvc_ioctl_s_try_ext_ctrls(struct uvc_fh *handle,
> {
> struct v4l2_ext_control *ctrl = ctrls->controls;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> unsigned int i;
> int ret;
>
> @@ -1104,9 +1196,15 @@ static int uvc_ioctl_s_try_ext_ctrls(struct uvc_fh *handle,
> if (ret < 0)
> return ret;
>
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> +
> ret = uvc_ctrl_begin(chain);
> - if (ret < 0)
> + if (ret < 0) {
> + uvc_pm_put(stream);
> return ret;
> + }
>
> for (i = 0; i < ctrls->count; ++ctrl, ++i) {
> ret = uvc_ctrl_set(handle, ctrl);
> @@ -1114,16 +1212,20 @@ static int uvc_ioctl_s_try_ext_ctrls(struct uvc_fh *handle,
> uvc_ctrl_rollback(handle);
> ctrls->error_idx = ioctl == VIDIOC_S_EXT_CTRLS ?
> ctrls->count : i;
> - return ret;
> + goto done;
> }
> }
>
> ctrls->error_idx = 0;
>
> if (ioctl == VIDIOC_S_EXT_CTRLS)
> - return uvc_ctrl_commit(handle, ctrls);
> + ret = uvc_ctrl_commit(handle, ctrls);
> else
> - return uvc_ctrl_rollback(handle);
> + ret = uvc_ctrl_rollback(handle);
> +
> +done:
> + uvc_pm_put(stream);
> + return ret;
> }
>
> static int uvc_ioctl_s_ext_ctrls(struct file *file, void *fh,
> @@ -1147,8 +1249,16 @@ static int uvc_ioctl_querymenu(struct file *file, void *fh,
> {
> struct uvc_fh *handle = fh;
> struct uvc_video_chain *chain = handle->chain;
> + struct uvc_streaming *stream = handle->stream;
> + int ret;
> +
> + ret = uvc_pm_get(stream);
> + if (ret)
> + return ret;
> + ret = uvc_query_v4l2_menu(chain, qm);
> + uvc_pm_put(stream);
>
> - return uvc_query_v4l2_menu(chain, qm);
> + return ret;
> }
>
> static int uvc_ioctl_g_selection(struct file *file, void *fh,
>
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2022-10-25 12:48 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-20 14:09 [PATCH v1 0/3] [RESEND] media: uvcvideo: Implement granular power management Ricardo Ribalda
2022-09-20 14:09 ` [PATCH v1 1/3] media: uvcvideo: Only create input devs if hw supports it Ricardo Ribalda
2022-09-20 14:09 ` [PATCH v1 2/3] media: uvcvideo: Refactor streamon/streamoff Ricardo Ribalda
2022-09-20 14:09 ` [PATCH v1 3/3] media: uvcvideo: Do power management granularly Ricardo Ribalda
2022-10-25 12:45 ` Laurent Pinchart [this message]
2022-10-25 12:55 ` Ricardo Ribalda
2022-10-25 13:07 ` Ricardo Ribalda
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y1facEGMo+N1v0RU@pendragon.ideasonboard.com \
--to=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=ribalda@chromium.org \
--cc=tfiga@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.