From: Thierry Reding <thierry.reding@gmail.com>
To: JC Kuo <jckuo@nvidia.com>
Cc: gregkh@linuxfoundation.org, robh@kernel.org,
jonathanh@nvidia.com, kishon@ti.com, linux-tegra@vger.kernel.org,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, nkristam@nvidia.com
Subject: Re: [PATCH v6 11/15] phy: tegra: xusb: Add wake/sleepwalk for Tegra210
Date: Tue, 19 Jan 2021 14:58:18 +0100 [thread overview]
Message-ID: <YAblelq2PGXGVKOX@ulmo> (raw)
In-Reply-To: <20210119085546.725005-12-jckuo@nvidia.com>
[-- Attachment #1: Type: text/plain, Size: 1248 bytes --]
On Tue, Jan 19, 2021 at 04:55:42PM +0800, JC Kuo wrote:
> This commit implements Tegra210 XUSB PADCTL wake and sleepwalk
> routines. Sleepwalk logic is in PMC (always-on) hardware block.
> PMC driver provides managed access to the sleepwalk registers
> via regmap framework.
>
> Signed-off-by: JC Kuo <jckuo@nvidia.com>
> ---
> v6:
> no change
> v5:
> no change
> v4:
> move sleepwalk/wake stubs from 'struct tegra_xusb_padctl_ops' to
> 'struct tegra_xusb_lane_ops'
> remove a blank line
> rename 'pmc_dev' with 'pdev'
> remove 'struct device_node *np'
> rename label 'no_pmc' with 'out'
> defer .probe() if PMC driver is yet to load
>
> v3:
> rename 'pmc_reg" with 'regmap' and move to the top of 'struct tegra210_xusb_padctl'
> change return data of .phy_remote_wake_detected() to 'bool'
> change input parameter of .phy_remote_wake_detected() to 'struct phy*'
> remove unnecessary 'else'
> rename 'val' with 'value'
> rename tegra_pmc_*() with tegra210_pmc_*()
> remove VBUS ON/OFF control change
>
> drivers/phy/tegra/xusb-tegra210.c | 930 ++++++++++++++++++++++++++++++
> 1 file changed, 930 insertions(+)
Acked-by: Thierry Reding <treding@nvidia.com>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2021-01-19 23:53 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-19 8:55 [PATCH v6 00/15] Tegra XHCI controller ELPG support JC Kuo
2021-01-19 8:55 ` [PATCH v6 01/15] clk: tegra: Add PLLE HW power sequencer control JC Kuo
2021-01-19 14:11 ` Thierry Reding
2021-02-11 3:06 ` Stephen Boyd
2021-01-19 8:55 ` [PATCH v6 02/15] clk: tegra: Don't enable PLLE HW sequencer at init JC Kuo
2021-01-19 14:12 ` Thierry Reding
2021-02-11 3:06 ` Stephen Boyd
2021-01-19 8:55 ` [PATCH v6 03/15] phy: tegra: xusb: Move usb3 port init for Tegra210 JC Kuo
2021-01-19 8:55 ` [PATCH v6 04/15] phy: tegra: xusb: tegra210: Do not reset UPHY PLL JC Kuo
2021-01-19 13:52 ` Thierry Reding
2021-01-20 1:42 ` JC Kuo
2021-01-19 8:55 ` [PATCH v6 05/15] phy: tegra: xusb: Rearrange UPHY init on Tegra210 JC Kuo
2021-01-19 8:55 ` [PATCH v6 06/15] phy: tegra: xusb: Add Tegra210 lane_iddq operation JC Kuo
2021-01-19 8:55 ` [PATCH v6 07/15] phy: tegra: xusb: Add sleepwalk and suspend/resume JC Kuo
2021-01-19 13:54 ` Thierry Reding
2021-01-19 8:55 ` [PATCH v6 08/15] soc/tegra: pmc: Provide USB sleepwalk register map JC Kuo
2021-01-19 8:55 ` [PATCH v6 09/15] arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop JC Kuo
2021-01-19 8:55 ` [PATCH v6 10/15] dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop JC Kuo
2021-01-19 8:55 ` [PATCH v6 11/15] phy: tegra: xusb: Add wake/sleepwalk for Tegra210 JC Kuo
2021-01-19 13:58 ` Thierry Reding [this message]
2021-01-19 8:55 ` [PATCH v6 12/15] phy: tegra: xusb: Tegra210 host mode VBUS control JC Kuo
2021-01-19 8:55 ` [PATCH v6 13/15] phy: tegra: xusb: Add wake/sleepwalk for Tegra186 JC Kuo
2021-01-19 13:59 ` Thierry Reding
2021-01-19 8:55 ` [PATCH v6 14/15] usb: host: xhci-tegra: Unlink power domain devices JC Kuo
2021-01-19 14:04 ` Thierry Reding
2021-01-19 8:55 ` [PATCH v6 15/15] xhci: tegra: Enable ELPG for runtime/system PM JC Kuo
2021-01-19 14:04 ` Thierry Reding
2021-01-19 14:07 ` [PATCH v6 00/15] Tegra XHCI controller ELPG support Thierry Reding
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YAblelq2PGXGVKOX@ulmo \
--to=thierry.reding@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jckuo@nvidia.com \
--cc=jonathanh@nvidia.com \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=nkristam@nvidia.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.