Re: [PATCH v2 3/5] ARM: dts: qcom: Add USB port definitions to ipq806x

[Bjorn Andersson <bjorn.andersson@linaro.org>]

On Thu 20 May 12:30 CDT 2021, Jonathan McDowell wrote:

> Signed-off-by: Jonathan McDowell <noodles@earth.li>
> ---
>  arch/arm/boot/dts/qcom-ipq8064.dtsi | 88 +++++++++++++++++++++++++++++
>  1 file changed, 88 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> index 9628092217cb..c66859abdfd5 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
> @@ -1026,6 +1026,94 @@
>  			status = "disabled";
>  		};
>  
> +		hs_phy_0: hs_phy_0 {

The node name should be some generic-thing@unit-address, so I fixed up
all your phys as "phy@100f8800" while applying your patches.

Thank you,
Bjorn

> +			compatible = "qcom,ipq806x-usb-phy-hs";
> +			reg = <0x100f8800 0x30>;
> +			clocks = <&gcc USB30_0_UTMI_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
> +		ss_phy_0: ss_phy_0 {
> +			compatible = "qcom,ipq806x-usb-phy-ss";
> +			reg = <0x100f8830 0x30>;
> +			clocks = <&gcc USB30_0_MASTER_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
> +		usb3_0: usb3@100f8800 {
> +			compatible = "qcom,dwc3", "syscon";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x100f8800 0x8000>;
> +			clocks = <&gcc USB30_0_MASTER_CLK>;
> +			clock-names = "core";
> +
> +			ranges;
> +
> +			resets = <&gcc USB30_0_MASTER_RESET>;
> +			reset-names = "master";
> +
> +			status = "disabled";
> +
> +			dwc3_0: dwc3@10000000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x10000000 0xcd00>;
> +				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&hs_phy_0>, <&ss_phy_0>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				dr_mode = "host";
> +				snps,dis_u3_susphy_quirk;
> +			};
> +		};
> +
> +		hs_phy_1: hs_phy_1 {
> +			compatible = "qcom,ipq806x-usb-phy-hs";
> +			reg = <0x110f8800 0x30>;
> +			clocks = <&gcc USB30_1_UTMI_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +		};
> +
> +		ss_phy_1: ss_phy_1 {
> +			compatible = "qcom,ipq806x-usb-phy-ss";
> +			reg = <0x110f8830 0x30>;
> +			clocks = <&gcc USB30_1_MASTER_CLK>;
> +			clock-names = "ref";
> +			#phy-cells = <0>;
> +		};
> +
> +		usb3_1: usb3@110f8800 {
> +			compatible = "qcom,dwc3", "syscon";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x110f8800 0x8000>;
> +			clocks = <&gcc USB30_1_MASTER_CLK>;
> +			clock-names = "core";
> +
> +			ranges;
> +
> +			resets = <&gcc USB30_1_MASTER_RESET>;
> +			reset-names = "master";
> +
> +			status = "disabled";
> +
> +			dwc3_1: dwc3@11000000 {
> +				compatible = "snps,dwc3";
> +				reg = <0x11000000 0xcd00>;
> +				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> +				phys = <&hs_phy_1>, <&ss_phy_1>;
> +				phy-names = "usb2-phy", "usb3-phy";
> +				dr_mode = "host";
> +				snps,dis_u3_susphy_quirk;
> +			};
> +		};
> +
>  		vsdcc_fixed: vsdcc-regulator {
>  			compatible = "regulator-fixed";
>  			regulator-name = "SDCC Power";
> -- 
> 2.20.1
>