From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: robdclark@gmail.com, sean@poorly.run, swboyd@chromium.org,
vkoul@kernel.org, agross@kernel.org, robh+dt@kernel.org,
devicetree@vger.kernel.org, abhinavk@codeaurora.org,
aravindh@codeaurora.org, freedreno@lists.freedesktop.org,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4] arm64: dts: qcom: sc7180: Add DisplayPort node
Date: Fri, 25 Jun 2021 11:13:45 -0500 [thread overview]
Message-ID: <YNYAuaBrGgdtToph@builder.lan> (raw)
In-Reply-To: <1622758940-13485-1-git-send-email-khsieh@codeaurora.org>
On Thu 03 Jun 17:22 CDT 2021, Kuogee Hsieh wrote:
> Add DP device node on sc7180.
>
> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
> ---
> Changes in v2:
> -- replace msm_dp with dp
> -- replace dp_opp_table with opp_table
>
> Changes in v3:
> -- correct text of commit title
>
> Changes in v4:
> -- replace dp with mdss_dp
> -- replace opp_table with dp_opp_table
>
>
> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 9 ++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 78 ++++++++++++++++++++++++++++
> 2 files changed, 87 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> index 24d293e..051fb40 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> @@ -786,6 +786,15 @@ hp_i2c: &i2c9 {
> status = "okay";
> };
>
> +&mdss_dp {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&dp_hot_plug_det>;
> + data-lanes = <0 1>;
> + vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>;
> + vdda-0p9-supply = <&vdda_usb_ss_dp_core>;
> +};
> +
> &pm6150_adc {
> charger-thermistor@4f {
> reg = <ADC5_AMUX_THM3_100K_PU>;
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 6228ba2..c779ad3 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -3032,6 +3032,13 @@
> remote-endpoint = <&dsi0_in>;
> };
> };
> +
> + port@2 {
> + reg = <2>;
> + dpu_intf0_out: endpoint {
> + remote-endpoint = <&dp_in>;
> + };
> + };
> };
>
> mdp_opp_table: mdp-opp-table {
> @@ -3148,6 +3155,77 @@
>
> status = "disabled";
> };
> +
> + mdss_dp: displayport-controller@ae90000 {
> + compatible = "qcom,sc7180-dp";
> + status = "disabled";
> +
> + reg = <0 0x0ae90000 0 0x1400>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <12>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
> + clock-names = "core_iface", "core_aux", "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + #clock-cells = <1>;
> + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
> + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
> + phys = <&dp_phy>;
> + phy-names = "dp";
> +
> + operating-points-v2 = <&dp_opp_table>;
> + power-domains = <&rpmhpd SC7180_CX>;
> +
> + #sound-dai-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + dp_in: endpoint {
> + remote-endpoint = <&dpu_intf0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dp_out: endpoint { };
> + };
> + };
> +
> + dp_opp_table: dp-opp-table {
I forgot that our discussion about the node name here was on the
previous revision, _this_ is the patch I will drop the "dp-" from and
apply.
And as I've looked at this quite a bit now:
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Thanks for following up on the other feedback!
Regards,
Bjorn
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> +
> };
>
> dispcc: clock-controller@af00000 {
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
next prev parent reply other threads:[~2021-06-25 16:13 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-03 22:22 [PATCH v4] arm64: dts: qcom: sc7180: Add DisplayPort node Kuogee Hsieh
2021-06-25 16:13 ` Bjorn Andersson [this message]
2021-06-30 17:51 ` Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YNYAuaBrGgdtToph@builder.lan \
--to=bjorn.andersson@linaro.org \
--cc=abhinavk@codeaurora.org \
--cc=agross@kernel.org \
--cc=aravindh@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=freedreno@lists.freedesktop.org \
--cc=khsieh@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robdclark@gmail.com \
--cc=robh+dt@kernel.org \
--cc=sean@poorly.run \
--cc=swboyd@chromium.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.