From: Greg KH <gregkh@linuxfoundation.org>
To: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: linux-staging@lists.linux.dev, neil@brown.name
Subject: Re: [PATCH] staging: mt7621-dts: get rid of nodes with no in-tree driver
Date: Mon, 18 Oct 2021 17:48:02 +0200 [thread overview]
Message-ID: <YW2XMkfAdbQm75j+@kroah.com> (raw)
In-Reply-To: <20211018153554.10471-1-sergio.paracuellos@gmail.com>
On Mon, Oct 18, 2021 at 05:35:53PM +0200, Sergio Paracuellos wrote:
> Nodes for 'i2s' and 'nand' have no driver present inside the linux tree.
> The normal approach for a dts file to be mainlined is start with those stuff
> which is already mainlined and get rid of the other stuff. If needed it will
> be properly added afterwards together with the suitable device driver. Hence,
> remove both nodes from the device tree include file.
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
> ---
> drivers/staging/mt7621-dts/mt7621.dtsi | 36 --------------------------
> 1 file changed, 36 deletions(-)
>
> diff --git a/drivers/staging/mt7621-dts/mt7621.dtsi b/drivers/staging/mt7621-dts/mt7621.dtsi
> index dd7d06c5f234..787220d4d3b4 100644
> --- a/drivers/staging/mt7621-dts/mt7621.dtsi
> +++ b/drivers/staging/mt7621-dts/mt7621.dtsi
> @@ -102,28 +102,6 @@ i2c: i2c@900 {
> pinctrl-0 = <&i2c_pins>;
> };
>
> - i2s: i2s@a00 {
> - compatible = "mediatek,mt7621-i2s";
> - reg = <0xa00 0x100>;
> -
> - clocks = <&sysc MT7621_CLK_I2S>;
> - clock-names = "i2s";
> - resets = <&sysc MT7621_RST_I2S>;
> - reset-names = "i2s";
> -
> - interrupt-parent = <&gic>;
> - interrupts = <GIC_SHARED 16 IRQ_TYPE_LEVEL_HIGH>;
> -
> - txdma-req = <2>;
> - rxdma-req = <3>;
> -
> - dmas = <&gdma 4>,
> - <&gdma 6>;
> - dma-names = "tx", "rx";
> -
> - status = "disabled";
> - };
> -
> memc: syscon@5000 {
> compatible = "mediatek,mt7621-memc", "syscon";
> reg = <0x5000 0x1000>;
> @@ -355,20 +333,6 @@ cdmm: cdmm@1fbf8000 {
> reg = <0x1fbf8000 0x8000>;
> };
>
> - nand: nand@1e003000 {
> - status = "disabled";
> -
> - compatible = "mediatek,mt7621-nand";
> - bank-width = <2>;
> - reg = <0x1e003000 0x800
> - 0x1e003800 0x800>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - clocks = <&sysc MT7621_CLK_NAND>;
> - clock-names = "nand";
> - };
> -
> ethernet: ethernet@1e100000 {
> compatible = "mediatek,mt7621-eth";
> reg = <0x1e100000 0x10000>;
> --
> 2.33.0
When trying to apply this I get:
checking file drivers/staging/mt7621-dts/mt7621.dtsi
Reversed (or previously applied) patch detected! Assume -R? [n]
Apply anyway? [n]
Skipping patch.
2 out of 2 hunks ignored
Are you sure you rebased?
Hm, ah, I can handle this with fuzz maybe:
patching file drivers/staging/mt7621-dts/mt7621.dtsi
Reversed (or previously applied) patch detected! Assume -R? [n] n
Apply anyway? [n] y
Hunk #1 FAILED at 102.
Hunk #2 succeeded at 358 (offset 3 lines).
1 out of 2 hunks FAILED -- saving rejects to file drivers/staging/mt7621-dts/mt7621.dtsi.rej
Nope, that didn't work.
Again, are you sure you rebased? Against what tree?
thanks,
greg k-h
next prev parent reply other threads:[~2021-10-18 15:48 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-18 15:35 [PATCH] staging: mt7621-dts: get rid of nodes with no in-tree driver Sergio Paracuellos
2021-10-18 15:35 ` Sergio Paracuellos
2021-10-18 15:48 ` Greg KH [this message]
2021-10-18 17:02 ` Sergio Paracuellos
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YW2XMkfAdbQm75j+@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=linux-staging@lists.linux.dev \
--cc=neil@brown.name \
--cc=sergio.paracuellos@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.