Re: [PATCH] ARM: dts: Add TS-7553-V2 support

[Rob Herring <robh@kernel.org>]

On Tue, Mar 22, 2022 at 05:31:05PM -0700, Kris Bahnsen wrote:
> Add initial support of the i.MX6UL based TS-7553-V2 platform.
> 
> Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
> ---
>  Documentation/devicetree/bindings/arm/fsl.yaml |   1 +
>  arch/arm/boot/dts/Makefile                     |   1 +
>  arch/arm/boot/dts/imx6ul-ts7553v2.dts          | 695 +++++++++++++++++++++++++
>  3 files changed, 697 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6ul-ts7553v2.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 97f6eebad76a..44fb8b445bff 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -563,6 +563,7 @@ properties:
>                - technexion,imx6ul-pico-dwarf   # TechNexion i.MX6UL Pico-Dwarf
>                - technexion,imx6ul-pico-hobbit  # TechNexion i.MX6UL Pico-Hobbit
>                - technexion,imx6ul-pico-pi      # TechNexion i.MX6UL Pico-Pi
> +              - technologic,ts7553v2      # embeddedTS TS-7553-V2
>            - const: fsl,imx6ul
>  
>        - description: i.MX6UL Armadeus Systems OPOS6UL SoM Board
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e41eca79c950..efc879dbbada 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -691,6 +691,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
>  	imx6ul-phytec-segin-ff-rdk-emmc.dtb \
>  	imx6ul-phytec-segin-ff-rdk-nand.dtb \
>  	imx6ul-prti6g.dtb \
> +	imx6ul-ts7553v2.dtb \
>  	imx6ul-tx6ul-0010.dtb \
>  	imx6ul-tx6ul-0011.dtb \
>  	imx6ul-tx6ul-mainboard.dtb \
> diff --git a/arch/arm/boot/dts/imx6ul-ts7553v2.dts b/arch/arm/boot/dts/imx6ul-ts7553v2.dts
> new file mode 100644
> index 000000000000..3ad18af8176d
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-ts7553v2.dts
> @@ -0,0 +1,695 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2022 Technologic Systems, Inc. dba embeddedTS
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include "imx6ul.dtsi"
> +
> +/ {
> +	model = "embeddedTS i.MX6UL TS-7553-V2";
> +	compatible = "technologic,ts7553v2", "fsl,imx6ul";
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0>;
> +	};
> +
> +	leds {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +		compatible = "gpio-leds";
> +
> +		green-led {
> +			label = "green-led";
> +			gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
> +			default-state = "on";
> +		};
> +
> +		red-led {
> +			label = "red-led";
> +			gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> +		left {
> +			label = "Left";
> +			gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_LEFT>;
> +			debounce-interval = <20>;
> +			gpio-key,wakeup;
> +		};
> +
> +		up {
> +			label = "Up";
> +			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_UP>;
> +			debounce-interval = <20>;
> +			gpio-key,wakeup;
> +		};
> +		down {
> +			label = "Down";
> +			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_DOWN>;
> +			debounce-interval = <20>;
> +			gpio-key,wakeup;
> +		};
> +		right {
> +			label = "Right";
> +			gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_RIGHT>;
> +			debounce-interval = <20>;
> +			gpio-key,wakeup;
> +		};
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			reusable;
> +			size = <0x4000000>;
> +			linux,cma-default;
> +		};
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";

This is not a bus. Move the child nodes to the top level.

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		reg_sd1_vmmc: regulator-sd1-vmmc {
> +			compatible = "regulator-fixed";
> +			regulator-name = "SD1-3V3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio3 12 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_enet_phy_3v3: regulator-phy {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_enet_3v3>;
> +			regulator-name = "ENET-3V3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_flexcan_3v3: regulator-can-3v3 {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_flexcan_3v3>;
> +			regulator-name = "CAN-EN";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio5 9 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	i2c_gpio: i2c-gpio {
> +		compatible = "i2c-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_i2cgpio>;
> +		gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>, /* sda */
> +			<&gpio5 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* scl */
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";

That's the default for a new node, not needed.

> +
> +		mpu9250a: imu@68 {
> +			compatible = "invensense,mpu9250";
> +			reg = <0x68>;
> +			interrupt-parent = <&gpio3>;
> +			interrupts = <1 IRQ_TYPE_EDGE_RISING>;
> +			i2c-gate {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				magnetometer@c {
> +					compatible = "asahi-kasei,ak8975";
> +					reg = <0x0c>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&gpio1 {
> +	gpio-line-names = "", "USB-5V-EN", "", "", "", "", "", "",
> +		"MODEM-5V-EN", "XBEE-3V3-EN", "", "", "", "", "", "", "", "",
> +		"", "", "", "", "", "RS232-XCEIVER-EN";
> +};
> +
> +&gpio2 {
> +	gpio-line-names = "", "", "", "", "", "", "", "",
> +		"XBEE-PIN-9", "XBEE-PIN-16", "", "", "", "",
> +		"XBEE-PIN-12";
> +
> +	vreg-mode {
> +		gpio-hog;
> +		gpios = <13 GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "VREG-MODE";
> +	};
> +};
> +
> +&gpio3 {
> +	gpio-line-names = "USB-HUB-RESET#", "", "", "", "", "", "",
> +		"USB-MUX-CPU-OTG", "", "", "", "NO-CHRG-JMP#", "", "", "", "",
> +		"", "SD-BOOT-JMP#", "PUSH-SW#", "U-BOOT-JMP#", "XBEE-RESET#",
> +		"", "", "RES-STRAP-0", "RES-STRAP-1", "", "",
> +		"RES-STRAP-2", "RES-STRAP-3";
> +};
> +
> +&gpio5 {
> +	gpio-line-names = "POWER-FAIL#", "", "EMMC-PWR-EN", "", "", "", "",
> +		"XBEE-USB-EN#", "RELAY-EN";
> +
> +	vdd-soc-in-v {

Should have 'hog' in the name. More specifically run 'make dtbs_check' 
on this which should have a warning for the the exact regex required. 
And don't add any other warnings (from this file, the SoC dtsi will have 
a bunch already).


> +		gpio-hog;
> +		gpios = <3 GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "VDD-SOC-IN-V";
> +	};
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	m41t00s: rtc@68 {
> +		compatible = "st,m41t00";
> +		reg = <0x68>;
> +	};
> +};
> +
> +
> +&i2c3 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	status = "okay";
> +};
> +
> +&ecspi3 {
> +	num-cs = <3>;
> +	cs-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>, <&gpio2 15 GPIO_ACTIVE_LOW>, <&gpio5 6 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi3>;
> +	status = "okay";
> +
> +	st7565p: lcd@0 {
> +		/* TODO: Add driver support for Sitronix ST7565p */
> +		reg = <0>;
> +		spi-max-frequency = <5000000>;
> +	};
> +
> +	spidevdc: spidev@1 {
> +		/*
> +		 * Open interface on pin-header. Add appropriate "compatible"
> +		 * and related properties here. The "reg" property should
> +		 * remain as-is.
> +		 */
> +		reg = <1>;
> +	};
> +
> +	fm25l16b: eeprom@2 {
> +		compatible = "atmel,at25";
> +		reg = <2>;
> +		spi-max-frequency = <20000000>;
> +		size = <0x800>;
> +		address-width = <16>;
> +		pagesize = <64>;
> +	};
> +};
> +
> +&ecspi4 {
> +	num-cs = <1>;
> +	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi4>;
> +	status = "okay";
> +
> +	/*
> +	 * In testing, the in-kernel wilc1000 driver was non-functional on SPI.
> +	 * However, it is possible to build the official Microchip driver
> +	 * outside of their kernel tree as an external module and it works
> +	 * just fine and allows for true WILC3000 compatibility with BLE support.
> +	 * The below compatible string is structured to prefer the external
> +	 * module and fallback to in-kernel if that ever becomes functional.
> +	 * Additionally, using both chip_en and enable gpios are in order to
> +	 * support both the external module and in-kernel driver.
> +	 */
> +	wilc: wifi@0 {
> +		compatible = "microchip,wilc3000", "microchip,wilc1000";
> +		reg = <0>;
> +		spi-max-frequency = <48000000>;
> +		reset-gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
> +		chip_en-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> +		enable-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> +		interrupt-parent = <&gpio5>;
> +		interrupts = <1 GPIO_ACTIVE_HIGH>;
> +		status = "okay";
> +	};
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet>;
> +	phy-mode = "rmii";
> +	phy-handle = <&ethphy0>;
> +	phy-supply = <&reg_enet_phy_3v3>;
> +	status = "okay";
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@1 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <2>;
> +			micrel,led-mode = <1>;
> +			clocks = <&clks IMX6UL_CLK_ENET_REF>;
> +			clock-names = "rmii-ref";
> +		};
> +	};
> +};
> +
> +&can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	xceiver-supply = <&reg_flexcan_3v3>;
> +	status = "okay";
> +};
> +
> +&can2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan2>;
> +	xceiver-supply = <&reg_flexcan_3v3>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	/*
> +	 * Need to use GPIO for TXEN even though CTS is available on this port.
> +	 * All instances of the UART2 RTS signal have other uses therefore leaving
> +	 * the UART module RTS_B input unconnected which generates spurious IRQs.
> +	 * If the imx.c driver is ever adjusted to allow configuration of RTSDEN
> +	 * then it may be possible to use real CTS here if RTS IRQs are disabled.
> +	 */
> +	rts-gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
> +	linux,rs485-enabled-at-boot-time;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4>;
> +	status = "okay";
> +};
> +
> +&uart5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart5>;
> +	status = "okay";
> +};
> +
> +&uart6 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart6>;
> +	cts-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
> +	rts-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +&uart7 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart7>;
> +	status = "okay";
> +};
> +
> +&uart8 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart8>;
> +	status = "okay";
> +};
> +
> +&usbotg1 {
> +	dr_mode = "peripheral";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg1_id>;
> +	srp-disable;
> +	hnp-disable;
> +	adp-disable;
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	dr_mode = "host";
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	keep-power-in-suspend;
> +	disable-wp;
> +	broken-cd = <1>;
> +	bus-width = <4>;
> +	vmmc-supply = <&reg_sd1_vmmc>;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	no-1-8-v;
> +	disable-wp;
> +	broken-cd = <1>;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog1>;
> +	fsl,ext-reset-output;
> +};
> +
> +&snvs_rtc {
> +	status = "disabled";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	pinctrl_hog: hoggrp {
> +		fsl,pins = <
> +			/* Reserved signals */
> +			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b020
> +			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x1a020
> +			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0x1a020
> +			MX6UL_PAD_LCD_DATA04__GPIO3_IO09	0x1a020
> +			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x1a020
> +			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x13020
> +			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x1b020
> +			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x1b020
> +			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x1b020
> +			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x1b020
> +			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x1b020
> +
> +
> +			/* Has hardware pull resistor */
> +			MX6UL_PAD_LCD_DATA14__GPIO3_IO19	0x1a020 /* U_BOOT_JMP#_ */
> +			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x1a020 /* NO_CHRG_JMP# */
> +			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x1a020 /* SD_BOOT_JMP# */
> +			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0x1a020 /* 6UL_TO_USB_DEV */
> +			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x1a020 /* MODEM 5 v */
> +			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x1a020 /* XBee 3.3 v */
> +			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1a020 /* eMMC En. */
> +			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0a0
> +
> +			/* Needs internal pull resistor */
> +			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x1b020 /* RES_STRAP_0 */
> +			MX6UL_PAD_LCD_DATA19__GPIO3_IO24	0x1b020 /* RES_STRAP_1 */
> +			MX6UL_PAD_LCD_DATA22__GPIO3_IO27	0x1b020 /* RES_STRAP_2 */
> +			MX6UL_PAD_LCD_DATA23__GPIO3_IO28	0x1b020 /* RES_STRAP_3 */
> +			MX6UL_PAD_LCD_DATA15__GPIO3_IO20	0x1b020 /* XBEE_RESET# */
> +			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b020 /* XBEE_USB_EN# */
> +			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14	0x1b020 /* XBEE_DIO_8 */
> +			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x1b020 /* XBEE_DIO_7 */
> +			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x1b020 /* XBEE_DIO_6 */
> +			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x1a020 /* RELAY_EN */
> +			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x1b020 /* USB 5v EN */
> +			MX6UL_PAD_LCD_CLK__GPIO3_IO00		0x1b020 /* USB_HUB_RESET# */
> +			MX6UL_PAD_ENET2_TX_DATA0__REF_CLK_24M	0x1b020 /* USB hub */
> +			MX6UL_PAD_LCD_DATA13__GPIO3_IO18	0x1a020 /* PUSH_SW_CPU# */
> +			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23	0x1b020 /* 232_TRANS_EN */
> +			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b020 /* POWER_FAIL */
> +		>;
> +	};
> +
> +	pinctrl_gpio_keys: gpiokeysgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x1a020 /* Left */
> +			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x1a020 /* Up */
> +			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x1a020 /* Down */
> +			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x1a020 /* Right */
> +		>;
> +	};
> +
> +	pinctrl_gpio_leds: gpioledgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x1b020 /* Red LED */
> +			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x1b020 /* Grn LED */
> +		>;
> +	};
> +
> +	pinctrl_usb_otg1_id: usbotg1idgrp {
> +		/* Wired always high for device mode on TS-7553-V2 */
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x16059
> +		>;
> +	};
> +
> +	pinctrl_flexcan1: flexcan1grp{
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_DATA08__FLEXCAN1_TX	0x1b020
> +			MX6UL_PAD_LCD_DATA09__FLEXCAN1_RX	0x1b020
> +		>;
> +	};
> +
> +	pinctrl_flexcan2: flexcan2grp{
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX	0x1b020
> +			MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX	0x1b020
> +		>;
> +	};
> +
> +	pinctrl_flexcan_3v3: flexcan3v3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x1b020 /* CAN En. */
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
> +			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
> +			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
> +			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
> +			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart5: uart5grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
> +			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart6: uart6grp {
> +		fsl,pins = <
> +			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
> +			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x1b0b1
> +			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart7: uart7grp {
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_DATA17__UART7_DCE_RX	0x1b0b1
> +			MX6UL_PAD_LCD_DATA16__UART7_DCE_TX	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart8: uart8grp {
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_DATA21__UART8_DCE_RX	0x1b0b1
> +			MX6UL_PAD_LCD_DATA20__UART8_DCE_TX	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_enet: enetgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
> +			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
> +		>;
> +	};
> +
> +	pinctrl_enet_3v3: enet3v3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO02__I2C1_SCL		0x4001a8b0
> +			MX6UL_PAD_GPIO1_IO03__I2C1_SDA		0x4001a8b0
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_DATA01__I2C3_SCL		0x4001a8b0
> +			MX6UL_PAD_LCD_DATA00__I2C3_SDA		0x4001a8b0
> +		>;
> +	};
> +
> +	pinctrl_i2cgpio: i2cgrpgpio {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x4001a8b0
> +			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x4001a8b0
> +			MX6UL_PAD_LCD_ENABLE__GPIO3_IO01	0x13020 /* IMU IRQ */
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			/* hysteresis, en 47k PU */
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10071
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
> +			MX6UL_PAD_LCD_DATA07__GPIO3_IO12	0x17059 /* EN_SD_POWER */
> +			MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT	0x17059
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> +		fsl,pins = <
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> +		fsl,pins = <
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
> +			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
> +			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
> +			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
> +			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
> +			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
> +		>;
> +	};
> +
> +	pinctrl_ecspi3: ecspi3grp {
> +		fsl,pins = <
> +			// XXX: These are not defined with GPIO names
> +			// See about porting LCD driver?
> +			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x1b020 /* LCD_BKLT */
> +			MX6UL_PAD_NAND_WP_B__GPIO4_IO11		0x1b020 /* LCD_RESET# */
> +			MX6UL_PAD_NAND_DQS__GPIO4_IO16		0x1b020 /* LCD_CMD# */
> +			MX6UL_PAD_NAND_CE0_B__ECSPI3_SCLK	0x1b020 /* SPI_3_CLK */
> +			MX6UL_PAD_NAND_CE1_B__ECSPI3_MOSI	0x1b020 /* SPI_3_MOSI */
> +			MX6UL_PAD_NAND_CLE__ECSPI3_MISO		0x1b820 /* SPI_3_MISO */
> +			MX6UL_PAD_NAND_READY_B__GPIO4_IO12	0x1b020 /* LCD CS0# */
> +			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b020 /* HD1 CS1# */
> +			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x1b020 /* FRAM CS2# */
> +		>;
> +	};
> +
> +	pinctrl_ecspi4: ecspi4grp {
> +		fsl,pins = <
> +			MX6UL_PAD_NAND_DATA04__ECSPI4_SCLK	0x1b020
> +			MX6UL_PAD_NAND_DATA05__ECSPI4_MOSI	0x1b020
> +			MX6UL_PAD_NAND_DATA06__ECSPI4_MISO	0x1b020
> +			MX6UL_PAD_NAND_DATA07__GPIO4_IO09	0x1b020 /* WIFI CS# */
> +			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b020 /* WIFI IRQ# */
> +			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x1b020 /* WIFI RST# */
> +			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x1b020 /* WIFI EN */
> +		>;
> +	};
> +
> +	pinctrl_wdog1: wdog1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY	0xb8b0
> +		>;
> +	};
> +};
> -- 
> 2.11.0
> 
>