* [PATCH 1/2] dt-bindings: arm: rockchip: Add MNT Reform 2 (RCORE)
@ 2025-01-30 11:53 ` Patrick Wildt
0 siblings, 0 replies; 12+ messages in thread
From: Patrick Wildt @ 2025-01-30 11:53 UTC (permalink / raw)
To: linux-rockchip
Cc: linux-arm-kernel, devicetree, Kever Yang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Document board compatible bindings.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 522a6f0450ea..bc995db8cbfe 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -710,6 +710,11 @@ properties:
- const: mqmaker,miqi
- const: rockchip,rk3288
+ - description: MNT Reform2 (RCORE)
+ items:
+ - const: mntre,reform2-rcore
+ - const: rockchip,rk3588
+
- description: Neardi LBA3368
items:
- const: neardi,lba3368
--
2.48.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
2025-01-30 11:53 ` Patrick Wildt
@ 2025-01-30 11:54 ` Patrick Wildt
-1 siblings, 0 replies; 12+ messages in thread
From: Patrick Wildt @ 2025-01-30 11:54 UTC (permalink / raw)
To: linux-rockchip
Cc: linux-arm-kernel, devicetree, Kever Yang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
MNT Reform 2 is an open source laptop with replaceable CPU modules,
including a version with the RK3588-based MNT RCORE[1]:
- Rockchip RK3588
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- SD Card slot
- Gigabit ethernet port
- HDMI port
- 2x mPCIe ports for WiFi or NVMe
- 3x USB 3.0 Type-A HOST port
[1] https://shop.mntre.com/products/mnt-reform
Signed-off-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Patrick Wildt <patrick@blueri.se>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3588-mnt-reform2.dts | 921 ++++++++++++++++++
2 files changed, 922 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index def1222c1907..88381d9a20e3 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -145,6 +145,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-firefly-itx-3588j.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-h96-max-v58.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-mnt-reform2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6-lts.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts b/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
new file mode 100644
index 000000000000..10c8e5fcc7c2
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
@@ -0,0 +1,921 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2024 MNT Research GmbH
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3588.dtsi"
+
+/ {
+ model = "MNT Reform 2 with RCORE RK3588 Module";
+ compatible = "mntre,reform2-rcore", "rockchip,rk3588";
+
+ aliases {
+ ethernet0 = &gmac0;
+ serial2 = &uart2;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ analog-sound {
+ compatible = "audio-graph-card";
+ label = "rk3588-wm8960";
+
+ widgets =
+ "Headphone", "Headphone Jack",
+ "Microphone", "Mic Jack",
+ "Speaker", "Ext Spk";
+
+ routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "Mic Jack", "MICB";
+
+ dais = <&i2s0_8ch_p0>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm8 0 10000 0>;
+ enable-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
+ brightness-levels = <0 8 16 32 64 128 160 200 255>;
+ default-brightness-level = <128>;
+ };
+
+ gmac0_clkin: external-gmac0-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac0_clkin";
+ #clock-cells = <0>;
+ };
+
+ pcie30_avdd1v8: pcie30-avdd1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd1v8";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&avcc_1v8_s0>;
+ };
+
+ pcie30_avdd0v75: pcie30-avdd0v75 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd0v75";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ vin-supply = <&avdd_0v75_s0>;
+ };
+
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_1v1_nldo_s3: vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie30: vcc3v3-pcie30 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie30";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_host: vcc5v0-host {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_host";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy1_ps {
+ status = "okay";
+};
+
+&combphy2_psu {
+ status = "okay";
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+ mem-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+ mem-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+ mem-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+ mem-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&display_subsystem {
+ clocks = <&hdptxphy_hdmi0>;
+ clock-names = "hdmi0_phy_pll";
+};
+
+&gmac0 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii-id";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus
+ &gmac0_clkinout
+ ð_phy_reset>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ sram-supply = <&vdd_gpu_mem_s0>;
+ status = "okay";
+};
+
+&hdmi0 {
+ enable-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&hdmi0_in {
+ hdmi0_in_vp2: endpoint {
+ remote-endpoint = <&vp2_out_hdmi0>;
+ };
+};
+
+&hdptxphy_hdmi0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0m2_xfer>;
+ status = "okay";
+
+ vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: rk8602@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+
+ vin-supply = <&vcc5v0_sys>;
+ fcs,suspend-voltage-selector = <1>;
+ rockchip,suspend-voltage-selector = <1>;
+
+ regulator-compatible = "rk860x-reg";
+ regulator-name = "vdd_cpu_big0_s0";
+ regulator-min-microvolt = <0x86470>;
+ regulator-max-microvolt = <0x100590>;
+ regulator-ramp-delay = <0x8fc>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: rk8603@43 {
+ compatible = "rockchip,rk8602", "rockchip,rk8603";
+ reg = <0x43>;
+
+ vin-supply = <&vcc5v0_sys>;
+ fcs,suspend-voltage-selector = <1>;
+ rockchip,suspend-voltage-selector = <1>;
+
+ regulator-compatible = "rk860x-reg";
+ regulator-name = "vdd_cpu_big1_s0";
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1m2_xfer>;
+ status = "okay";
+
+ vdd_npu_s0: vdd_npu_mem_s0: regulator@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_npu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6m0_xfer>;
+
+ wm8960: codec@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&cru I2S0_8CH_MCLKOUT>;
+ clock-names = "mclk";
+ assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+
+ port {
+ wm8960_p0: endpoint {
+ remote-endpoint = <&i2s0_8ch_p0_0>;
+ };
+ };
+ };
+
+ rtc@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+};
+
+&i2s0_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_lrck
+ &i2s0_mclk
+ &i2s0_sclk
+ &i2s0_sdi0
+ &i2s0_sdo0>;
+ status = "okay";
+
+ i2s0_8ch_p0: port {
+ i2s0_8ch_p0_0: endpoint {
+ dai-format = "i2s";
+ mclk-fs = <256>;
+ remote-endpoint = <&wm8960_p0>;
+ };
+ };
+};
+
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie2_0_rst>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_reset>;
+ reset-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
+ num-lanes = <1>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&pwm8 {
+ pinctrl-0 = <&pwm8m2_pins>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&avcc_1v8_s0>;
+ status = "okay";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ max-frequency = <150000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ max-frequency = <40000000>;
+ no-sdio;
+ no-mmc;
+ no-1-8-v;
+ cap-sd-highspeed;
+ vqmmc-supply = <&vcc3v3_pcie30>;
+ vmmc-supply = <&vcc3v3_pcie30>;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+};
+
+&spi2 {
+ status = "okay";
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ num-cs = <1>;
+
+ rk806single: pmic@0 {
+ compatible = "rockchip,rk806";
+ spi-max-frequency = <1000000>;
+ reg = <0x0>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default", "pmic-power-off";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ pinctrl-1 = <&rk806_dvs1_pwrdn>;
+
+ pmic-reset-func = <1>;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs1_slp: rk806_dvs1_slp {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs1_pwrdn: rk806_dvs1_pwrdn {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs1_rst: rk806_dvs1_rst {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_null: rk806_dvs2_null {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_slp: rk806_dvs2_slp {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs2_pwrdn: rk806_dvs2_pwrdn {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs2_rst: rk806_dvs2_rst {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_dvs: rk806_dvs2_dvs {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs2_gpio: rk806_dvs2_gpio {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun5";
+ };
+
+ rk806_dvs3_null: rk806_dvs3_null {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_slp: rk806_dvs3_slp {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs3_pwrdn: rk806_dvs3_pwrdn {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs3_rst: rk806_dvs3_rst {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs3_dvs: rk806_dvs3_dvs {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs3_gpio: rk806_dvs3_gpio {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun5";
+ };
+
+ regulators {
+ vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+ regulator-name = "vdd_gpu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <400>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-name = "vdd_log_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-name = "vdd_vdenc_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-init-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+
+ };
+
+ vdd_ddr_s0: dcdc-reg5 {
+ regulator-name = "vdd_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-name = "vdd2_ddr_s3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-name = "vcc_3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg9 {
+ regulator-name = "vddq_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg10 {
+ regulator-name = "vcc_1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "avcc_1v8_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s0: pldo-reg2 {
+ regulator-name = "vcc_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avdd_1v2_s0: pldo-reg3 {
+ regulator-name = "avdd_1v2_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-name = "vcc_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-name = "vccio_sd_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ pldo6_s3: pldo-reg6 {
+ regulator-name = "pldo6_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-name = "vdd_0v75_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_ddr_pll_s0: nldo-reg2 {
+ regulator-name = "vdd_ddr_pll_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg3 {
+ regulator-name = "avdd_0v75_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg4 {
+ regulator-name = "vdd_0v85_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v75_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&mdio0 {
+ rgmii_phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ };
+};
+
+&pinctrl {
+ dp {
+ dp1_hpd: dp1-hpd {
+ rockchip,pins = <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie2 {
+ pcie2_0_rst: pcie2-0-rst {
+ rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie3 {
+ pcie3_reset: pcie3-reset {
+ rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ eth_phy {
+ eth_phy_reset: eth-phy-reset {
+ rockchip,pins = <3 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ status = "okay";
+};
+
+&usbdp_phy1 {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vp2 {
+ vp2_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi0_in_vp2>;
+ };
+};
--
2.48.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
@ 2025-01-30 11:54 ` Patrick Wildt
0 siblings, 0 replies; 12+ messages in thread
From: Patrick Wildt @ 2025-01-30 11:54 UTC (permalink / raw)
To: linux-rockchip
Cc: linux-arm-kernel, devicetree, Kever Yang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
MNT Reform 2 is an open source laptop with replaceable CPU modules,
including a version with the RK3588-based MNT RCORE[1]:
- Rockchip RK3588
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- SD Card slot
- Gigabit ethernet port
- HDMI port
- 2x mPCIe ports for WiFi or NVMe
- 3x USB 3.0 Type-A HOST port
[1] https://shop.mntre.com/products/mnt-reform
Signed-off-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Patrick Wildt <patrick@blueri.se>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3588-mnt-reform2.dts | 921 ++++++++++++++++++
2 files changed, 922 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index def1222c1907..88381d9a20e3 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -145,6 +145,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-firefly-itx-3588j.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-h96-max-v58.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-mnt-reform2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6-lts.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts b/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
new file mode 100644
index 000000000000..10c8e5fcc7c2
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts
@@ -0,0 +1,921 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2024 MNT Research GmbH
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3588.dtsi"
+
+/ {
+ model = "MNT Reform 2 with RCORE RK3588 Module";
+ compatible = "mntre,reform2-rcore", "rockchip,rk3588";
+
+ aliases {
+ ethernet0 = &gmac0;
+ serial2 = &uart2;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ analog-sound {
+ compatible = "audio-graph-card";
+ label = "rk3588-wm8960";
+
+ widgets =
+ "Headphone", "Headphone Jack",
+ "Microphone", "Mic Jack",
+ "Speaker", "Ext Spk";
+
+ routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "Mic Jack", "MICB";
+
+ dais = <&i2s0_8ch_p0>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm8 0 10000 0>;
+ enable-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
+ brightness-levels = <0 8 16 32 64 128 160 200 255>;
+ default-brightness-level = <128>;
+ };
+
+ gmac0_clkin: external-gmac0-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac0_clkin";
+ #clock-cells = <0>;
+ };
+
+ pcie30_avdd1v8: pcie30-avdd1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd1v8";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&avcc_1v8_s0>;
+ };
+
+ pcie30_avdd0v75: pcie30-avdd0v75 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd0v75";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ vin-supply = <&avdd_0v75_s0>;
+ };
+
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_1v1_nldo_s3: vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie30: vcc3v3-pcie30 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie30";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_host: vcc5v0-host {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_host";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy1_ps {
+ status = "okay";
+};
+
+&combphy2_psu {
+ status = "okay";
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+ mem-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+ mem-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+ mem-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+ mem-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+ mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&display_subsystem {
+ clocks = <&hdptxphy_hdmi0>;
+ clock-names = "hdmi0_phy_pll";
+};
+
+&gmac0 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii-id";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus
+ &gmac0_clkinout
+ ð_phy_reset>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ sram-supply = <&vdd_gpu_mem_s0>;
+ status = "okay";
+};
+
+&hdmi0 {
+ enable-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&hdmi0_in {
+ hdmi0_in_vp2: endpoint {
+ remote-endpoint = <&vp2_out_hdmi0>;
+ };
+};
+
+&hdptxphy_hdmi0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0m2_xfer>;
+ status = "okay";
+
+ vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: rk8602@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+
+ vin-supply = <&vcc5v0_sys>;
+ fcs,suspend-voltage-selector = <1>;
+ rockchip,suspend-voltage-selector = <1>;
+
+ regulator-compatible = "rk860x-reg";
+ regulator-name = "vdd_cpu_big0_s0";
+ regulator-min-microvolt = <0x86470>;
+ regulator-max-microvolt = <0x100590>;
+ regulator-ramp-delay = <0x8fc>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: rk8603@43 {
+ compatible = "rockchip,rk8602", "rockchip,rk8603";
+ reg = <0x43>;
+
+ vin-supply = <&vcc5v0_sys>;
+ fcs,suspend-voltage-selector = <1>;
+ rockchip,suspend-voltage-selector = <1>;
+
+ regulator-compatible = "rk860x-reg";
+ regulator-name = "vdd_cpu_big1_s0";
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ regulator-boot-on;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1m2_xfer>;
+ status = "okay";
+
+ vdd_npu_s0: vdd_npu_mem_s0: regulator@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_npu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6m0_xfer>;
+
+ wm8960: codec@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&cru I2S0_8CH_MCLKOUT>;
+ clock-names = "mclk";
+ assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+
+ port {
+ wm8960_p0: endpoint {
+ remote-endpoint = <&i2s0_8ch_p0_0>;
+ };
+ };
+ };
+
+ rtc@68 {
+ compatible = "nxp,pcf8523";
+ reg = <0x68>;
+ };
+};
+
+&i2s0_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_lrck
+ &i2s0_mclk
+ &i2s0_sclk
+ &i2s0_sdi0
+ &i2s0_sdo0>;
+ status = "okay";
+
+ i2s0_8ch_p0: port {
+ i2s0_8ch_p0_0: endpoint {
+ dai-format = "i2s";
+ mclk-fs = <256>;
+ remote-endpoint = <&wm8960_p0>;
+ };
+ };
+};
+
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pcie2_0_rst>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_reset>;
+ reset-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
+ num-lanes = <1>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&pwm8 {
+ pinctrl-0 = <&pwm8m2_pins>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&avcc_1v8_s0>;
+ status = "okay";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ max-frequency = <150000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ max-frequency = <40000000>;
+ no-sdio;
+ no-mmc;
+ no-1-8-v;
+ cap-sd-highspeed;
+ vqmmc-supply = <&vcc3v3_pcie30>;
+ vmmc-supply = <&vcc3v3_pcie30>;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+};
+
+&spi2 {
+ status = "okay";
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ num-cs = <1>;
+
+ rk806single: pmic@0 {
+ compatible = "rockchip,rk806";
+ spi-max-frequency = <1000000>;
+ reg = <0x0>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default", "pmic-power-off";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ pinctrl-1 = <&rk806_dvs1_pwrdn>;
+
+ pmic-reset-func = <1>;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs1_slp: rk806_dvs1_slp {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs1_pwrdn: rk806_dvs1_pwrdn {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs1_rst: rk806_dvs1_rst {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_null: rk806_dvs2_null {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_slp: rk806_dvs2_slp {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs2_pwrdn: rk806_dvs2_pwrdn {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs2_rst: rk806_dvs2_rst {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_dvs: rk806_dvs2_dvs {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs2_gpio: rk806_dvs2_gpio {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun5";
+ };
+
+ rk806_dvs3_null: rk806_dvs3_null {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_slp: rk806_dvs3_slp {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs3_pwrdn: rk806_dvs3_pwrdn {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs3_rst: rk806_dvs3_rst {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs3_dvs: rk806_dvs3_dvs {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs3_gpio: rk806_dvs3_gpio {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun5";
+ };
+
+ regulators {
+ vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+ regulator-name = "vdd_gpu_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <400>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-name = "vdd_log_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-name = "vdd_vdenc_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-init-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+
+ };
+
+ vdd_ddr_s0: dcdc-reg5 {
+ regulator-name = "vdd_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-name = "vdd2_ddr_s3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-name = "vcc_3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg9 {
+ regulator-name = "vddq_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg10 {
+ regulator-name = "vcc_1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "avcc_1v8_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s0: pldo-reg2 {
+ regulator-name = "vcc_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ avdd_1v2_s0: pldo-reg3 {
+ regulator-name = "avdd_1v2_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-name = "vcc_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-name = "vccio_sd_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ pldo6_s3: pldo-reg6 {
+ regulator-name = "pldo6_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-name = "vdd_0v75_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_ddr_pll_s0: nldo-reg2 {
+ regulator-name = "vdd_ddr_pll_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg3 {
+ regulator-name = "avdd_0v75_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg4 {
+ regulator-name = "vdd_0v85_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v75_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&mdio0 {
+ rgmii_phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ };
+};
+
+&pinctrl {
+ dp {
+ dp1_hpd: dp1-hpd {
+ rockchip,pins = <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie2 {
+ pcie2_0_rst: pcie2-0-rst {
+ rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie3 {
+ pcie3_reset: pcie3-reset {
+ rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ eth_phy {
+ eth_phy_reset: eth-phy-reset {
+ rockchip,pins = <3 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ status = "okay";
+};
+
+&usbdp_phy1 {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vp2 {
+ vp2_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi0_in_vp2>;
+ };
+};
--
2.48.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
2025-01-30 11:54 ` Patrick Wildt
@ 2025-01-30 12:05 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2025-01-30 12:05 UTC (permalink / raw)
To: Patrick Wildt, linux-rockchip
Cc: linux-arm-kernel, devicetree, Kever Yang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On 30/01/2025 12:54, Patrick Wildt wrote:
> +
> +&hdptxphy_hdmi0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0m2_xfer>;
> + status = "okay";
> +
> + vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: rk8602@42 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> +
> + vin-supply = <&vcc5v0_sys>;
> + fcs,suspend-voltage-selector = <1>;
> + rockchip,suspend-voltage-selector = <1>;
> +
> + regulator-compatible = "rk860x-reg";
> + regulator-name = "vdd_cpu_big0_s0";
> + regulator-min-microvolt = <0x86470>;
> + regulator-max-microvolt = <0x100590>;
> + regulator-ramp-delay = <0x8fc>;
> + regulator-boot-on;
> + regulator-always-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: rk8603@43 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "rockchip,rk8602", "rockchip,rk8603";
> + reg = <0x43>;
> +
...
> +&spi2 {
> + status = "okay";
> + assigned-clocks = <&cru CLK_SPI2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
> + num-cs = <1>;
> +
> + rk806single: pmic@0 {
> + compatible = "rockchip,rk806";
> + spi-max-frequency = <1000000>;
> + reg = <0x0>;
reg is always theh second property.
> +
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + pinctrl-names = "default", "pmic-power-off";
> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> + pinctrl-1 = <&rk806_dvs1_pwrdn>;
> +
> + pmic-reset-func = <1>;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc_1v1_nldo_s3>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + #gpio-cells = <2>;
> + gpio-controller;
> +
> + rk806_dvs1_null: dvs1-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs1_slp: rk806_dvs1_slp {
No underscores in node names. Missing suffix also suggests this fails
tests, so standard disclaimer:
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Maybe you need to update your dtschema and yamllint. Don't rely on
distro packages for dtschema and be sure you are using the latest
released dtschema.
> + pins = "gpio_pwrctrl1";
> + function = "pin_fun1";
> + };
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
@ 2025-01-30 12:05 ` Krzysztof Kozlowski
0 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2025-01-30 12:05 UTC (permalink / raw)
To: Patrick Wildt, linux-rockchip
Cc: linux-arm-kernel, devicetree, Kever Yang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On 30/01/2025 12:54, Patrick Wildt wrote:
> +
> +&hdptxphy_hdmi0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0m2_xfer>;
> + status = "okay";
> +
> + vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: rk8602@42 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> +
> + vin-supply = <&vcc5v0_sys>;
> + fcs,suspend-voltage-selector = <1>;
> + rockchip,suspend-voltage-selector = <1>;
> +
> + regulator-compatible = "rk860x-reg";
> + regulator-name = "vdd_cpu_big0_s0";
> + regulator-min-microvolt = <0x86470>;
> + regulator-max-microvolt = <0x100590>;
> + regulator-ramp-delay = <0x8fc>;
> + regulator-boot-on;
> + regulator-always-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: rk8603@43 {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "rockchip,rk8602", "rockchip,rk8603";
> + reg = <0x43>;
> +
...
> +&spi2 {
> + status = "okay";
> + assigned-clocks = <&cru CLK_SPI2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
> + num-cs = <1>;
> +
> + rk806single: pmic@0 {
> + compatible = "rockchip,rk806";
> + spi-max-frequency = <1000000>;
> + reg = <0x0>;
reg is always theh second property.
> +
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + pinctrl-names = "default", "pmic-power-off";
> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> + pinctrl-1 = <&rk806_dvs1_pwrdn>;
> +
> + pmic-reset-func = <1>;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc_1v1_nldo_s3>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + #gpio-cells = <2>;
> + gpio-controller;
> +
> + rk806_dvs1_null: dvs1-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs1_slp: rk806_dvs1_slp {
No underscores in node names. Missing suffix also suggests this fails
tests, so standard disclaimer:
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Maybe you need to update your dtschema and yamllint. Don't rely on
distro packages for dtschema and be sure you are using the latest
released dtschema.
> + pins = "gpio_pwrctrl1";
> + function = "pin_fun1";
> + };
Best regards,
Krzysztof
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
2025-01-30 12:05 ` Krzysztof Kozlowski
@ 2025-02-10 22:14 ` Patrick Wildt
-1 siblings, 0 replies; 12+ messages in thread
From: Patrick Wildt @ 2025-02-10 22:14 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: linux-rockchip, linux-arm-kernel, devicetree, Kever Yang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On Thu, Jan 30, 2025 at 01:05:45PM +0100, Krzysztof Kozlowski wrote:
> On 30/01/2025 12:54, Patrick Wildt wrote:
> > + rk806_dvs1_slp: rk806_dvs1_slp {
>
> No underscores in node names. Missing suffix also suggests this fails
> tests, so standard disclaimer:
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
> Maybe you need to update your dtschema and yamllint. Don't rely on
> distro packages for dtschema and be sure you are using the latest
> released dtschema.
Hi Krzysztof,
You were right, I did not know about that; thanks for bringing that to
my attention! I've prepared a v2 that I'll send out now which does seem
to be happy with the schema, and hope fix those issues plus a few more.
Please let me know if there's anything else that I might have missed.
Thanks,
Patrick
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH 2/2] arm64: dts: rockchip: add MNT Reform 2
@ 2025-02-10 22:14 ` Patrick Wildt
0 siblings, 0 replies; 12+ messages in thread
From: Patrick Wildt @ 2025-02-10 22:14 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: linux-rockchip, linux-arm-kernel, devicetree, Kever Yang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On Thu, Jan 30, 2025 at 01:05:45PM +0100, Krzysztof Kozlowski wrote:
> On 30/01/2025 12:54, Patrick Wildt wrote:
> > + rk806_dvs1_slp: rk806_dvs1_slp {
>
> No underscores in node names. Missing suffix also suggests this fails
> tests, so standard disclaimer:
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
> Maybe you need to update your dtschema and yamllint. Don't rely on
> distro packages for dtschema and be sure you are using the latest
> released dtschema.
Hi Krzysztof,
You were right, I did not know about that; thanks for bringing that to
my attention! I've prepared a v2 that I'll send out now which does seem
to be happy with the schema, and hope fix those issues plus a few more.
Please let me know if there's anything else that I might have missed.
Thanks,
Patrick
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add MNT Reform 2 (RCORE)
2025-01-30 11:53 ` Patrick Wildt
@ 2025-01-30 23:38 ` Rob Herring (Arm)
-1 siblings, 0 replies; 12+ messages in thread
From: Rob Herring (Arm) @ 2025-01-30 23:38 UTC (permalink / raw)
To: Patrick Wildt
Cc: linux-rockchip, Kever Yang, Krzysztof Kozlowski, Heiko Stuebner,
linux-arm-kernel, devicetree, Conor Dooley
On Thu, 30 Jan 2025 12:53:29 +0100, Patrick Wildt wrote:
> Document board compatible bindings.
>
> Signed-off-by: Patrick Wildt <patrick@blueri.se>
> ---
> Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/rockchip/' for Z5toOecuMiBXM6aF@windev.fritz.box:
arch/arm64/boot/dts/rockchip/rk3588-base.dtsi:355.39-358.4: Warning (clocks_property): /display-subsystem: Missing property '#clock-cells' in node /phy@fed60000 or bad phandle (referred from clocks[0])
also defined at arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts:200.20-203.3
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: display-subsystem: 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/rockchip/rockchip-drm.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8602@42: Unevaluated properties are not allowed ('regulator-compatible', 'rockchip,suspend-voltage-selector' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8603@43: compatible: 'oneOf' conditional failed, one must be fixed:
['rockchip,rk8602', 'rockchip,rk8603'] is too long
'rockchip,rk8601' was expected
'rockchip,rk8603' was expected
'rockchip,rk8600' was expected
'rockchip,rk8602' was expected
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8603@43: Unevaluated properties are not allowed ('compatible', 'regulator-compatible', 'rockchip,suspend-voltage-selector' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: hdmi@fde80000: Unevaluated properties are not allowed ('enable-gpios' was unexpected)
from schema $id: http://devicetree.org/schemas/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: pmic@0: regulators:dcdc-reg4: Unevaluated properties are not allowed ('regulator-init-microvolt' was unexpected)
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: pmic@0: Unevaluated properties are not allowed ('pmic-reset-func', 'regulators', 'rk806_dvs1_pwrdn', 'rk806_dvs1_rst', 'rk806_dvs1_slp', 'rk806_dvs2_dvs', 'rk806_dvs2_gpio', 'rk806_dvs2_null', 'rk806_dvs2_pwrdn', 'rk806_dvs2_rst', 'rk806_dvs2_slp', 'rk806_dvs3_dvs', 'rk806_dvs3_gpio', 'rk806_dvs3_null', 'rk806_dvs3_pwrdn', 'rk806_dvs3_rst', 'rk806_dvs3_slp' were unexpected)
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: codec@1a: Unevaluated properties are not allowed ('port' was unexpected)
from schema $id: http://devicetree.org/schemas/sound/wlf,wm8960.yaml#
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add MNT Reform 2 (RCORE)
@ 2025-01-30 23:38 ` Rob Herring (Arm)
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring (Arm) @ 2025-01-30 23:38 UTC (permalink / raw)
To: Patrick Wildt
Cc: linux-rockchip, Kever Yang, Krzysztof Kozlowski, Heiko Stuebner,
linux-arm-kernel, devicetree, Conor Dooley
On Thu, 30 Jan 2025 12:53:29 +0100, Patrick Wildt wrote:
> Document board compatible bindings.
>
> Signed-off-by: Patrick Wildt <patrick@blueri.se>
> ---
> Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/rockchip/' for Z5toOecuMiBXM6aF@windev.fritz.box:
arch/arm64/boot/dts/rockchip/rk3588-base.dtsi:355.39-358.4: Warning (clocks_property): /display-subsystem: Missing property '#clock-cells' in node /phy@fed60000 or bad phandle (referred from clocks[0])
also defined at arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dts:200.20-203.3
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: display-subsystem: 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/rockchip/rockchip-drm.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8602@42: Unevaluated properties are not allowed ('regulator-compatible', 'rockchip,suspend-voltage-selector' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8603@43: compatible: 'oneOf' conditional failed, one must be fixed:
['rockchip,rk8602', 'rockchip,rk8603'] is too long
'rockchip,rk8601' was expected
'rockchip,rk8603' was expected
'rockchip,rk8600' was expected
'rockchip,rk8602' was expected
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: rk8603@43: Unevaluated properties are not allowed ('compatible', 'regulator-compatible', 'rockchip,suspend-voltage-selector' were unexpected)
from schema $id: http://devicetree.org/schemas/regulator/fcs,fan53555.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: hdmi@fde80000: Unevaluated properties are not allowed ('enable-gpios' was unexpected)
from schema $id: http://devicetree.org/schemas/display/rockchip/rockchip,rk3588-dw-hdmi-qp.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: pmic@0: regulators:dcdc-reg4: Unevaluated properties are not allowed ('regulator-init-microvolt' was unexpected)
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: pmic@0: Unevaluated properties are not allowed ('pmic-reset-func', 'regulators', 'rk806_dvs1_pwrdn', 'rk806_dvs1_rst', 'rk806_dvs1_slp', 'rk806_dvs2_dvs', 'rk806_dvs2_gpio', 'rk806_dvs2_null', 'rk806_dvs2_pwrdn', 'rk806_dvs2_rst', 'rk806_dvs2_slp', 'rk806_dvs3_dvs', 'rk806_dvs3_gpio', 'rk806_dvs3_null', 'rk806_dvs3_pwrdn', 'rk806_dvs3_rst', 'rk806_dvs3_slp' were unexpected)
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
arch/arm64/boot/dts/rockchip/rk3588-mnt-reform2.dtb: codec@1a: Unevaluated properties are not allowed ('port' was unexpected)
from schema $id: http://devicetree.org/schemas/sound/wlf,wm8960.yaml#
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add MNT Reform 2 (RCORE)
2025-01-30 11:53 ` Patrick Wildt
@ 2025-01-31 7:42 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2025-01-31 7:42 UTC (permalink / raw)
To: Patrick Wildt
Cc: linux-rockchip, linux-arm-kernel, devicetree, Kever Yang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On Thu, Jan 30, 2025 at 12:53:29PM +0100, Patrick Wildt wrote:
> Document board compatible bindings.
>
> Signed-off-by: Patrick Wildt <patrick@blueri.se>
> ---
> Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add MNT Reform 2 (RCORE)
@ 2025-01-31 7:42 ` Krzysztof Kozlowski
0 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2025-01-31 7:42 UTC (permalink / raw)
To: Patrick Wildt
Cc: linux-rockchip, linux-arm-kernel, devicetree, Kever Yang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
On Thu, Jan 30, 2025 at 12:53:29PM +0100, Patrick Wildt wrote:
> Document board compatible bindings.
>
> Signed-off-by: Patrick Wildt <patrick@blueri.se>
> ---
> Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 12+ messages in thread