Re: [PATCH v2 2/2] arm64: dts: qcom: x1e80100: Add some issing nodes for CRD

[Abel Vesa <abel.vesa@linaro.org>]

On 23-12-15 00:35:38, Abel Vesa wrote:
> Enable touchscreen, touchpad, keyboard, display, pcie and usb
> and all related nodes.

Urgh, type in subject. I'll rephrase it anyway in the next version.

Please ignore this version.

> 
> Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 221 ++++++++++++++++++++++++++++++
>  1 file changed, 221 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> index 7532d8eca2de..d44898453315 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
> @@ -401,10 +401,144 @@ vreg_l3j_0p8: ldo3 {
>  	};
>  };
>  
> +&i2c0 {
> +	clock-frequency = <400000>;
> +
> +	status = "okay";
> +
> +	touchpad@15 {
> +		compatible = "hid-over-i2c";
> +		reg = <0x15>;
> +
> +		hid-descr-addr = <0x1>;
> +		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&tpad_default>;
> +
> +		wakeup-source;
> +	};
> +
> +	keyboard@3a {
> +		compatible = "hid-over-i2c";
> +		reg = <0x3a>;
> +
> +		hid-descr-addr = <0x1>;
> +		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&kybd_default>;
> +		wakeup-source;
> +	};
> +};
> +
> +&i2c8 {
> +	clock-frequency = <400000>;
> +
> +	status = "okay";
> +
> +	touchscreen@10 {
> +		compatible = "hid-over-i2c";
> +		reg = <0x10>;
> +
> +		hid-descr-addr = <0x1>;
> +		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&ts0_default>;
> +	};
> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_dp3 {
> +	compatible = "qcom,x1e80100-dp";
> +	/delete-property/ #sound-dai-cells;
> +
> +	data-lanes = <0 1 2 3>;
> +
> +	status = "okay";
> +
> +	aux-bus {
> +		panel {
> +			compatible = "edp-panel";
> +			power-supply = <&vreg_edp_3p3>;
> +
> +			port {
> +				edp_panel_in: endpoint {
> +					remote-endpoint = <&mdss_dp3_out>;
> +				};
> +			};
> +		};
> +	};
> +
> +	ports {
> +		port@1 {
> +			reg = <1>;
> +			mdss_dp3_out: endpoint {
> +				remote-endpoint = <&edp_panel_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&mdss_dp3_phy {
> +	vdda-phy-supply = <&vreg_l3j_0p8>;
> +	vdda-pll-supply = <&vreg_l2j_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&pcie4 {
> +	status = "okay";
> +};
> +
> +&pcie4_phy {
> +	vdda-phy-supply = <&vreg_l3j_0p8>;
> +	vdda-pll-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&pcie6a {
> +	status = "okay";
> +};
> +
> +&pcie6a_phy {
> +	vdda-phy-supply = <&vreg_l3j_0p8>;
> +	vdda-pll-supply = <&vreg_l2j_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&qupv3_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_1 {
> +	status = "okay";
> +};
> +
>  &qupv3_2 {
>  	status = "okay";
>  };
>  
> +&remoteproc_adsp {
> +	firmware-name = "qcom/x1e80100/adsp.mbn",
> +			"qcom/x1e80100/adsp_dtb.mbn";
> +
> +	status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> +	firmware-name = "qcom/x1e80100/cdsp.mbn",
> +			"qcom/x1e80100/cdsp_dtb.mbn";
> +
> +	status = "okay";
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <34 2>, /* Unused */
>  			       <44 4>, /* SPI (TPM) */
> @@ -416,9 +550,96 @@ edp_reg_en: edp-reg-en-state {
>  		drive-strength = <16>;
>  		bias-disable;
>  	};
> +
> +	kybd_default: kybd-default-state {
> +		pins = "gpio67";
> +		function = "gpio";
> +		bias-disable;
> +	};
> +
> +	tpad_default: tpad-default-state {
> +		pins = "gpio3";
> +		function = "gpio";
> +		bias-disable;
> +	};
> +
> +	ts0_default: ts0-default-state {
> +		int-n-pins {
> +			pins = "gpio51";
> +			function = "gpio";
> +			bias-disable;
> +		};
> +
> +		reset-n-pins {
> +			pins = "gpio48";
> +			function = "gpio";
> +			output-high;
> +			drive-strength = <16>;
> +		};
> +	};
>  };
>  
>  &uart21 {
>  	compatible = "qcom,geni-debug-uart";
>  	status = "okay";
>  };
> +
> +&usb_1_ss0_hsphy {
> +	vdd-supply = <&vreg_l2e_0p8>;
> +	vdda12-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&usb_1_ss0_qmpphy {
> +	status = "okay";
> +};
> +
> +&usb_1_ss0 {
> +	status = "okay";
> +};
> +
> +&usb_1_ss0_dwc3 {
> +	dr_mode = "host";
> +	usb-role-switch;
> +};
> +
> +&usb_1_ss1_hsphy {
> +	vdd-supply = <&vreg_l2e_0p8>;
> +	vdda12-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&usb_1_ss1_qmpphy {
> +	status = "okay";
> +};
> +
> +&usb_1_ss1 {
> +	status = "okay";
> +};
> +
> +&usb_1_ss1_dwc3 {
> +	dr_mode = "host";
> +	usb-role-switch;
> +};
> +
> +&usb_1_ss2_hsphy {
> +	vdd-supply = <&vreg_l2e_0p8>;
> +	vdda12-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&usb_1_ss2_qmpphy {
> +	status = "okay";
> +};
> +
> +&usb_1_ss2 {
> +	status = "okay";
> +};
> +
> +&usb_1_ss2_dwc3 {
> +	dr_mode = "host";
> +	usb-role-switch;
> +};
> 
> -- 
> 2.34.1
>