From: Krzysztof Kozlowski <krzk@kernel.org>
To: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-media@vger.kernel.org, linux-kernel@vger.kernel.org,
Devarsh Thakkar <devarsht@ti.com>,
Jai Luthra <jai.luthra@ideasonboard.com>,
Sakari Ailus <sakari.ailus@linux.intel.com>,
devicetree@vger.kernel.org, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>
Subject: Re: [PATCH 17/19] media: dt-bindings: ti,ds90ub960: Add "i2c-addr" link property
Date: Wed, 15 Jan 2025 21:25:46 +0100 [thread overview]
Message-ID: <a869e66e-4fb0-49b6-9307-9a20c73cb374@kernel.org> (raw)
In-Reply-To: <b083ab17-a34e-42cf-9696-ff774731dc58@ideasonboard.com>
On 15/01/2025 18:19, Tomi Valkeinen wrote:
> Hi,
>
> On 15/01/2025 10:40, Krzysztof Kozlowski wrote:
>
>>>> Why only these folks? Why not all of the maintainers?
>>>
>>> The whole series is sent to the media list and maintainers. I thought
>>> this single patch doesn't warrant sending the whole series to DT list
>>> and maintainers, so I cc'd them here.
>>
>>
>> I was wondering why only some of the DT maintainers, not all? My usual
>> assumption is: you are not using get_maintainers.pl or you are working
>> on an old kernel.
>
> It's simpler than that: a copy-paste mistake. I'm not sure how I managed
> to miss Conor there.
>
> Any preference on cc'ing the DT maintainers and the dt-list only for
> this patch (I'll use --- this time, I promise!), or just sending the
> whole series also to DT people?
I think only Rob uses DT list entirely. I use both - DT list and being
directly CC-ed on emails, and I think Conor relies on being Cc-ed
directly. IOW, just cc all maintainers + DT list. Unless you touch
multiple subsystems, there is rarely a point to strip get_maintainers.pl
output from maintainers/reviewers/submitters. Do not confuse in skipping
non-maintainers pointed by Git-fallback (not applicable to b4, I think),
because these should be used carefully.
Best regards,
Krzysztof
next prev parent reply other threads:[~2025-01-15 20:25 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-01-10 9:14 [PATCH 00/19] media: i2c: ds90ub9xx: Error handling, UB9702 improvements Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 01/19] media: i2c: ds90ub953: Fix error prints Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 02/19] media: i2c: ds90ub913: Align ub913_read() with other similar functions Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 03/19] media: i2c: ds90ub9xx: Add err parameter to read/write funcs Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 04/19] media: i2c: ds90ub960: Add error handling to multiple places Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 05/19] media: i2c: ds90ub953: Add error handling to ub953_log_status() Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 06/19] media: i2c: ds90ub913: Add error handling to ub913_log_status() Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 07/19] media: i2c: ds90ub953: Speed-up I2C watchdog timer Tomi Valkeinen
2025-01-15 14:17 ` Sakari Ailus
2025-01-24 13:19 ` Tomi Valkeinen
2025-02-03 9:23 ` Sakari Ailus
2025-01-10 9:14 ` [PATCH 08/19] media: i2c: ds90ub960: Move UB9702 registers to a separate section Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 09/19] media: i2c: ds90ub960: Add UB9702 specific registers Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 10/19] media: i2c: ds90ub960: Split ub960_init_tx_ports() Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 11/19] media: i2c: ds90ub960: Refresh ub960_init_tx_ports_ub9702() Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 12/19] media: i2c: ds90ub960: Add RX port iteration support Tomi Valkeinen
2025-01-15 14:23 ` Sakari Ailus
2025-01-24 13:34 ` Tomi Valkeinen
2025-02-03 9:27 ` Sakari Ailus
2025-01-10 9:14 ` [PATCH 13/19] media: i2c: ds90ub960: Move all RX port init code into ub960_init_rx_ports() Tomi Valkeinen
2025-01-15 14:25 ` Sakari Ailus
2025-01-24 13:23 ` Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 14/19] media: i2c: ds90ub960: Remove old ub9702 RX port init code (SQUASH) Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 15/19] media: i2c: ds90ub960: Update UB9702 init sequences Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 16/19] media: i2c: ds90ub960: Enable SSCG for UB9702 Tomi Valkeinen
2025-01-15 14:26 ` Sakari Ailus
2025-01-15 16:04 ` Tomi Valkeinen
2025-01-16 9:58 ` Sakari Ailus
2025-01-16 10:05 ` Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 17/19] media: dt-bindings: ti,ds90ub960: Add "i2c-addr" link property Tomi Valkeinen
2025-01-11 10:31 ` Krzysztof Kozlowski
2025-01-14 11:50 ` Tomi Valkeinen
2025-01-15 8:40 ` Krzysztof Kozlowski
2025-01-15 17:19 ` Tomi Valkeinen
2025-01-15 20:25 ` Krzysztof Kozlowski [this message]
2025-01-15 15:53 ` Konstantin Ryabitsev
2025-01-15 16:09 ` Tomi Valkeinen
2025-01-15 16:46 ` Krzysztof Kozlowski
2025-01-15 17:14 ` Tomi Valkeinen
2025-01-10 9:14 ` [PATCH 18/19] media: i2c: ds90ub960: Configure serializer using back-channel Tomi Valkeinen
2025-01-15 14:29 ` Sakari Ailus
2025-01-24 13:29 ` Tomi Valkeinen
2025-02-03 9:28 ` Sakari Ailus
2025-01-10 9:14 ` [PATCH 19/19] media: i2c: ds90ub9xx: Set serializer temperature ramp Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a869e66e-4fb0-49b6-9307-9a20c73cb374@kernel.org \
--to=krzk@kernel.org \
--cc=devarsht@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=jai.luthra@ideasonboard.com \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=robh@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=tomi.valkeinen@ideasonboard.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.