* [PATCH v8 1/6] serial: 8250: make saved LSR larger
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 2/6] serial: 8250: create lsr_save_mask Ilpo Järvinen
` (4 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Paul Cercueil, linux-kernel,
linux-mips
Cc: Andy Shevchenko, Lukas Wunner, Uwe Kleine-König,
Lino Sanfilippo, Ilpo Järvinen
DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.
Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250.h | 4 ++--
drivers/tty/serial/8250/8250_exar.c | 2 +-
drivers/tty/serial/8250/8250_fsl.c | 2 +-
drivers/tty/serial/8250/8250_ingenic.c | 2 +-
drivers/tty/serial/8250/8250_omap.c | 7 +++----
drivers/tty/serial/8250/8250_port.c | 17 +++++++++--------
include/linux/serial_8250.h | 6 +++---
7 files changed, 20 insertions(+), 20 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index b120da57c61f..0ff5688ba90c 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -133,9 +133,9 @@ static inline void serial_out(struct uart_8250_port *up, int offset, int value)
*
* Returns LSR value or'ed with the preserved flags (if any).
*/
-static inline unsigned int serial_lsr_in(struct uart_8250_port *up)
+static inline u16 serial_lsr_in(struct uart_8250_port *up)
{
- unsigned int lsr = up->lsr_saved_flags;
+ u16 lsr = up->lsr_saved_flags;
lsr |= serial_in(up, UART_LSR);
up->lsr_saved_flags = lsr & LSR_SAVE_FLAGS;
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 528779b40049..3d999eec4087 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -195,11 +195,11 @@ static int xr17v35x_startup(struct uart_port *port)
static void exar_shutdown(struct uart_port *port)
{
- unsigned char lsr;
bool tx_complete = false;
struct uart_8250_port *up = up_to_u8250p(port);
struct circ_buf *xmit = &port->state->xmit;
int i = 0;
+ u16 lsr;
do {
lsr = serial_in(up, UART_LSR);
diff --git a/drivers/tty/serial/8250/8250_fsl.c b/drivers/tty/serial/8250/8250_fsl.c
index 9c01c531349d..fd4005fcd0d6 100644
--- a/drivers/tty/serial/8250/8250_fsl.c
+++ b/drivers/tty/serial/8250/8250_fsl.c
@@ -25,8 +25,8 @@
int fsl8250_handle_irq(struct uart_port *port)
{
- unsigned char lsr, orig_lsr;
unsigned long flags;
+ u16 lsr, orig_lsr;
unsigned int iir;
struct uart_8250_port *up = up_to_u8250p(port);
diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c
index cff91aa03f29..2b2f5d8d24b9 100644
--- a/drivers/tty/serial/8250/8250_ingenic.c
+++ b/drivers/tty/serial/8250/8250_ingenic.c
@@ -54,7 +54,7 @@ static void early_out(struct uart_port *port, int offset, uint8_t value)
static void ingenic_early_console_putc(struct uart_port *port, unsigned char c)
{
- uint8_t lsr;
+ u16 lsr;
do {
lsr = early_in(port, UART_LSR);
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index ac8bfa042391..0dcecbbc3967 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -1115,8 +1115,7 @@ static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
return omap_8250_rx_dma(up);
}
-static unsigned char omap_8250_handle_rx_dma(struct uart_8250_port *up,
- u8 iir, unsigned char status)
+static u16 omap_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir, u16 status)
{
if ((status & (UART_LSR_DR | UART_LSR_BI)) &&
(iir & UART_IIR_RDI)) {
@@ -1130,7 +1129,7 @@ static unsigned char omap_8250_handle_rx_dma(struct uart_8250_port *up,
}
static void am654_8250_handle_rx_dma(struct uart_8250_port *up, u8 iir,
- unsigned char status)
+ u16 status)
{
/*
* Queue a new transfer if FIFO has data.
@@ -1164,7 +1163,7 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
struct omap8250_priv *priv = up->port.private_data;
- unsigned char status;
+ u16 status;
u8 iir;
serial8250_rpm_get(up);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index c860f5964138..19c612d732cf 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1508,7 +1508,7 @@ static inline void __stop_tx(struct uart_8250_port *p)
struct uart_8250_em485 *em485 = p->em485;
if (em485) {
- unsigned char lsr = serial_lsr_in(p);
+ u16 lsr = serial_lsr_in(p);
u64 stop_delay = 0;
if (!(lsr & UART_LSR_THRE))
@@ -1565,7 +1565,7 @@ static inline void __start_tx(struct uart_port *port)
if (serial8250_set_THRI(up)) {
if (up->bugs & UART_BUG_TXEN) {
- unsigned char lsr = serial_lsr_in(up);
+ u16 lsr = serial_lsr_in(up);
if (lsr & UART_LSR_THRE)
serial8250_tx_chars(up);
@@ -1719,7 +1719,7 @@ static void serial8250_enable_ms(struct uart_port *port)
serial8250_rpm_put(up);
}
-void serial8250_read_char(struct uart_8250_port *up, unsigned char lsr)
+void serial8250_read_char(struct uart_8250_port *up, u16 lsr)
{
struct uart_port *port = &up->port;
unsigned char ch;
@@ -1788,7 +1788,7 @@ EXPORT_SYMBOL_GPL(serial8250_read_char);
* (such as THRE) because the LSR value might come from an already consumed
* character.
*/
-unsigned char serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
+u16 serial8250_rx_chars(struct uart_8250_port *up, u16 lsr)
{
struct uart_port *port = &up->port;
int max_count = 256;
@@ -1908,10 +1908,10 @@ static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
*/
int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
{
- unsigned char status;
struct uart_8250_port *up = up_to_u8250p(port);
bool skip_rx = false;
unsigned long flags;
+ u16 status;
if (iir & UART_IIR_NO_INT)
return 0;
@@ -1994,7 +1994,7 @@ static unsigned int serial8250_tx_empty(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
- unsigned int lsr;
+ u16 lsr;
serial8250_rpm_get(up);
@@ -2117,8 +2117,8 @@ static void wait_for_xmitr(struct uart_8250_port *up, int bits)
static int serial8250_get_poll_char(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
- unsigned char lsr;
int status;
+ u16 lsr;
serial8250_rpm_get(up);
@@ -2173,8 +2173,9 @@ int serial8250_do_startup(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned long flags;
- unsigned char lsr, iir;
+ unsigned char iir;
int retval;
+ u16 lsr;
if (!port->fifosize)
port->fifosize = uart_config[port->type].fifo_size;
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index ff84a3ed10ea..4565f25ba9a2 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -119,7 +119,7 @@ struct uart_8250_port {
* be immediately processed.
*/
#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
- unsigned char lsr_saved_flags;
+ u16 lsr_saved_flags;
#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
unsigned char msr_saved_flags;
@@ -170,8 +170,8 @@ extern void serial8250_do_set_divisor(struct uart_port *port, unsigned int baud,
unsigned int quot_frac);
extern int fsl8250_handle_irq(struct uart_port *port);
int serial8250_handle_irq(struct uart_port *port, unsigned int iir);
-unsigned char serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr);
-void serial8250_read_char(struct uart_8250_port *up, unsigned char lsr);
+u16 serial8250_rx_chars(struct uart_8250_port *up, u16 lsr);
+void serial8250_read_char(struct uart_8250_port *up, u16 lsr);
void serial8250_tx_chars(struct uart_8250_port *up);
unsigned int serial8250_modem_status(struct uart_8250_port *up);
void serial8250_init_port(struct uart_8250_port *up);
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v8 2/6] serial: 8250: create lsr_save_mask
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 1/6] serial: 8250: make saved LSR larger Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 3/6] serial: 8250_lpss: Use 32-bit reads Ilpo Järvinen
` (3 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Andy Shevchenko, linux-kernel
Cc: Lukas Wunner, Uwe Kleine-König, Lino Sanfilippo,
Ilpo Järvinen
Allow drivers to alter LSR save mask.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250.h | 2 +-
drivers/tty/serial/8250/8250_core.c | 4 ++++
drivers/tty/serial/8250/8250_dw.c | 2 +-
include/linux/serial_8250.h | 1 +
4 files changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 0ff5688ba90c..5cc967fe3b59 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -138,7 +138,7 @@ static inline u16 serial_lsr_in(struct uart_8250_port *up)
u16 lsr = up->lsr_saved_flags;
lsr |= serial_in(up, UART_LSR);
- up->lsr_saved_flags = lsr & LSR_SAVE_FLAGS;
+ up->lsr_saved_flags = lsr & up->lsr_save_mask;
return lsr;
}
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 90ddc8924811..57e86133af4f 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -1007,6 +1007,7 @@ int serial8250_register_8250_port(const struct uart_8250_port *up)
uart->port.rs485 = up->port.rs485;
uart->rs485_start_tx = up->rs485_start_tx;
uart->rs485_stop_tx = up->rs485_stop_tx;
+ uart->lsr_save_mask = up->lsr_save_mask;
uart->dma = up->dma;
/* Take tx_loadsz from fifosize if it wasn't set separately */
@@ -1094,6 +1095,9 @@ int serial8250_register_8250_port(const struct uart_8250_port *up)
ret = 0;
}
+ if (!uart->lsr_save_mask)
+ uart->lsr_save_mask = LSR_SAVE_FLAGS; /* Use default LSR mask */
+
/* Initialise interrupt backoff work if required */
if (up->overrun_backoff_time_ms > 0) {
uart->overrun_backoff_time_ms =
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index 4cc69bb612ab..167a691c7b19 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -129,7 +129,7 @@ static void dw8250_tx_wait_empty(struct uart_port *p)
while (tries--) {
lsr = readb (p->membase + (UART_LSR << p->regshift));
- up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+ up->lsr_saved_flags |= lsr & up->lsr_save_mask;
if (lsr & UART_LSR_TEMT)
break;
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 4565f25ba9a2..8c7b793aa4d7 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -120,6 +120,7 @@ struct uart_8250_port {
*/
#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
u16 lsr_saved_flags;
+ u16 lsr_save_mask;
#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
unsigned char msr_saved_flags;
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v8 3/6] serial: 8250_lpss: Use 32-bit reads
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 1/6] serial: 8250: make saved LSR larger Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 2/6] serial: 8250: create lsr_save_mask Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
2022-06-20 6:40 ` Ilpo Järvinen
` (2 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Andy Shevchenko, linux-kernel
Cc: Lukas Wunner, Uwe Kleine-König, Lino Sanfilippo,
Ilpo Järvinen
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_lpss.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index 0f5af061e0b4..4ba43bef9933 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -330,7 +330,7 @@ static int lpss8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
uart.port.irq = pci_irq_vector(pdev, 0);
uart.port.private_data = &lpss->data;
uart.port.type = PORT_16550A;
- uart.port.iotype = UPIO_MEM;
+ uart.port.iotype = UPIO_MEM32;
uart.port.regshift = 2;
uart.port.uartclk = lpss->board->base_baud * 16;
uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v8 4/6] serial: take termios_rwsem for ->rs485_config() & pass termios as param
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
2022-06-20 6:40 ` [PATCH v8 2/6] serial: 8250: create lsr_save_mask Ilpo Järvinen
` (4 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Andy Shevchenko,
Vladimir Zapolskiy, Russell King, Richard Genoud, Nicolas Ferre,
Alexandre Belloni, Claudiu Beznea, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
Maxime Coquelin, Alexandre Torgue, linux-kernel, linux-arm-kernel,
linux-stm32
Cc: Lukas Wunner, Uwe Kleine-König, Lino Sanfilippo,
Ilpo Järvinen
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250.h | 3 ++-
drivers/tty/serial/8250/8250_dwlib.c | 3 ++-
drivers/tty/serial/8250/8250_exar.c | 9 +++++----
drivers/tty/serial/8250/8250_fintek.c | 2 +-
drivers/tty/serial/8250/8250_lpc18xx.c | 2 +-
drivers/tty/serial/8250/8250_pci.c | 2 +-
drivers/tty/serial/8250/8250_port.c | 3 ++-
drivers/tty/serial/amba-pl011.c | 2 +-
drivers/tty/serial/ar933x_uart.c | 2 +-
drivers/tty/serial/atmel_serial.c | 2 +-
drivers/tty/serial/fsl_lpuart.c | 4 ++--
drivers/tty/serial/imx.c | 2 +-
drivers/tty/serial/max310x.c | 2 +-
drivers/tty/serial/mcf.c | 3 ++-
drivers/tty/serial/omap-serial.c | 3 ++-
drivers/tty/serial/sc16is7xx.c | 2 +-
drivers/tty/serial/serial_core.c | 14 ++++++++++----
drivers/tty/serial/stm32-usart.c | 2 +-
include/linux/serial_core.h | 1 +
19 files changed, 38 insertions(+), 25 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 5cc967fe3b59..287153d32536 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -203,7 +203,8 @@ void serial8250_rpm_put(struct uart_8250_port *p);
void serial8250_rpm_get_tx(struct uart_8250_port *p);
void serial8250_rpm_put_tx(struct uart_8250_port *p);
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485);
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485);
void serial8250_em485_start_tx(struct uart_8250_port *p);
void serial8250_em485_stop_tx(struct uart_8250_port *p);
void serial8250_em485_destroy(struct uart_8250_port *p);
diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
index c83e7eaf3877..d1ff3daeb0ba 100644
--- a/drivers/tty/serial/8250/8250_dwlib.c
+++ b/drivers/tty/serial/8250/8250_dwlib.c
@@ -85,7 +85,8 @@ void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios, struct
}
EXPORT_SYMBOL_GPL(dw8250_do_set_termios);
-static int dw8250_rs485_config(struct uart_port *p, struct serial_rs485 *rs485)
+static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
u32 tcr;
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 3d999eec4087..f5344cfe303c 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -112,7 +112,8 @@
struct exar8250;
struct exar8250_platform {
- int (*rs485_config)(struct uart_port *, struct serial_rs485 *);
+ int (*rs485_config)(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485);
const struct serial_rs485 *rs485_supported;
int (*register_gpio)(struct pci_dev *, struct uart_8250_port *);
void (*unregister_gpio)(struct uart_8250_port *);
@@ -409,7 +410,7 @@ static void xr17v35x_unregister_gpio(struct uart_8250_port *port)
port->port.private_data = NULL;
}
-static int generic_rs485_config(struct uart_port *port,
+static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -441,7 +442,7 @@ static const struct exar8250_platform exar8250_default_platform = {
.rs485_supported = &generic_rs485_supported,
};
-static int iot2040_rs485_config(struct uart_port *port,
+static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -471,7 +472,7 @@ static int iot2040_rs485_config(struct uart_port *port,
value |= mode;
writeb(value, p + UART_EXAR_MPIOLVL_7_0);
- return generic_rs485_config(port, rs485);
+ return generic_rs485_config(port, termios, rs485);
}
static const struct serial_rs485 iot2040_rs485_supported = {
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 1fb86c73786c..eea693f5b577 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -191,7 +191,7 @@ static int fintek_8250_get_ldn_range(struct fintek_8250 *pdata, int *min,
return -ENODEV;
}
-static int fintek_8250_rs485_config(struct uart_port *port,
+static int fintek_8250_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
uint8_t config = 0;
diff --git a/drivers/tty/serial/8250/8250_lpc18xx.c b/drivers/tty/serial/8250/8250_lpc18xx.c
index 3a1cb51cbc91..d7cb3bb52069 100644
--- a/drivers/tty/serial/8250/8250_lpc18xx.c
+++ b/drivers/tty/serial/8250/8250_lpc18xx.c
@@ -32,7 +32,7 @@ struct lpc18xx_uart_data {
int line;
};
-static int lpc18xx_rs485_config(struct uart_port *port,
+static int lpc18xx_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct uart_8250_port *up = up_to_u8250p(port);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index b6d71268aa7d..d31d2350a9db 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1553,7 +1553,7 @@ pci_brcm_trumanage_setup(struct serial_private *priv,
#define FINTEK_RTS_INVERT BIT(5)
/* We should do proper H/W transceiver setting before change to RS485 mode */
-static int pci_fintek_rs485_config(struct uart_port *port,
+static int pci_fintek_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct pci_dev *pci_dev = to_pci_dev(port->dev);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 19c612d732cf..5cb3673f9ee5 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -664,7 +664,8 @@ EXPORT_SYMBOL_GPL(serial8250_em485_supported);
* if the uart is incapable of driving RTS as a Transmit Enable signal in
* hardware, relying on software emulation instead.
*/
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485)
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
struct uart_8250_port *up = up_to_u8250p(port);
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index eccd66625d25..c8f52945a4aa 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -2197,7 +2197,7 @@ static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
return ret;
}
-static int pl011_rs485_config(struct uart_port *port,
+static int pl011_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct uart_amba_port *uap =
diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index ab2c5b2a1ce8..b73ce13683db 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -580,7 +580,7 @@ static const struct uart_ops ar933x_uart_ops = {
.verify_port = ar933x_uart_verify_port,
};
-static int ar933x_config_rs485(struct uart_port *port,
+static int ar933x_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct ar933x_uart_port *up =
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 74dd1d3ac46f..64dd6fea0a30 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -285,7 +285,7 @@ static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
}
/* Enable or disable the rs485 support */
-static int atmel_config_rs485(struct uart_port *port,
+static int atmel_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index d35414cb3e4e..8fe0494d4057 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1355,7 +1355,7 @@ static void lpuart_dma_rx_free(struct uart_port *port)
sport->dma_rx_cookie = -EINVAL;
}
-static int lpuart_config_rs485(struct uart_port *port,
+static int lpuart_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct lpuart_port *sport = container_of(port,
@@ -1385,7 +1385,7 @@ static int lpuart_config_rs485(struct uart_port *port,
return 0;
}
-static int lpuart32_config_rs485(struct uart_port *port,
+static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct lpuart_port *sport = container_of(port,
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index f4edde54175f..3457006cea3f 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1907,7 +1907,7 @@ static void imx_uart_poll_put_char(struct uart_port *port, unsigned char c)
#endif
/* called with port.lock taken and irqs off or from .probe without locking */
-static int imx_uart_rs485_config(struct uart_port *port,
+static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct imx_port *sport = (struct imx_port *)port;
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index d7d1791fcb57..5a8521fb9237 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -1026,7 +1026,7 @@ static void max310x_rs_proc(struct work_struct *ws)
MAX310X_MODE2_ECHOSUPR_BIT, mode2);
}
-static int max310x_rs485_config(struct uart_port *port,
+static int max310x_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct max310x_one *one = to_max310x_port(port);
diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
index 036f178e3d66..73c5287b8e5e 100644
--- a/drivers/tty/serial/mcf.c
+++ b/drivers/tty/serial/mcf.c
@@ -431,7 +431,8 @@ static int mcf_verify_port(struct uart_port *port, struct serial_struct *ser)
/****************************************************************************/
/* Enable or disable the RS485 support */
-static int mcf_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+static int mcf_config_rs485(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
unsigned char mr1, mr2;
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 98622c35d896..1d1e48ff33d8 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1325,7 +1325,8 @@ static inline void serial_omap_add_console_port(struct uart_omap_port *up)
/* Enable or disable the rs485 support */
static int
-serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+serial_omap_config_rs485(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned int mode;
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 2ceecaa4a478..8cb92a3b3fb8 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1127,7 +1127,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
spin_unlock_irqrestore(&port->lock, flags);
}
-static int sc16is7xx_config_rs485(struct uart_port *port,
+static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 621fc15e2e54..44c3785445e3 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1359,7 +1359,7 @@ int uart_rs485_config(struct uart_port *port)
uart_sanitize_serial_rs485(port, rs485);
- ret = port->rs485_config(port, rs485);
+ ret = port->rs485_config(port, NULL, rs485);
if (ret)
memset(rs485, 0, sizeof(*rs485));
@@ -1383,7 +1383,7 @@ static int uart_get_rs485_config(struct uart_port *port,
return 0;
}
-static int uart_set_rs485_config(struct uart_port *port,
+static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
struct serial_rs485 __user *rs485_user)
{
struct serial_rs485 rs485;
@@ -1402,7 +1402,7 @@ static int uart_set_rs485_config(struct uart_port *port,
uart_sanitize_serial_rs485(port, &rs485);
spin_lock_irqsave(&port->lock, flags);
- ret = port->rs485_config(port, &rs485);
+ ret = port->rs485_config(port, &tty->termios, &rs485);
if (!ret)
port->rs485 = rs485;
spin_unlock_irqrestore(&port->lock, flags);
@@ -1511,6 +1511,10 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
if (ret != -ENOIOCTLCMD)
goto out;
+ /* rs485_config requires more locking than others */
+ if (cmd == TIOCGRS485)
+ down_write(&tty->termios_rwsem);
+
mutex_lock(&port->mutex);
uport = uart_port_check(state);
@@ -1534,7 +1538,7 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
break;
case TIOCSRS485:
- ret = uart_set_rs485_config(uport, uarg);
+ ret = uart_set_rs485_config(tty, uport, uarg);
break;
case TIOCSISO7816:
@@ -1551,6 +1555,8 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
}
out_up:
mutex_unlock(&port->mutex);
+ if (cmd == TIOCGRS485)
+ up_write(&tty->termios_rwsem);
out:
return ret;
}
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index db3dd9731ee1..13992e64a7df 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -97,7 +97,7 @@ static void stm32_usart_config_reg_rs485(u32 *cr1, u32 *cr3, u32 delay_ADE,
*cr1 |= rs485_deat_dedt;
}
-static int stm32_usart_config_rs485(struct uart_port *port,
+static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct stm32_port *stm32_port = to_stm32_port(port);
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 5518b70177b3..17bbd0412a23 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -132,6 +132,7 @@ struct uart_port {
unsigned int old);
void (*handle_break)(struct uart_port *);
int (*rs485_config)(struct uart_port *,
+ struct ktermios *termios,
struct serial_rs485 *rs485);
int (*iso7816_config)(struct uart_port *,
struct serial_iso7816 *iso7816);
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH v8 4/6] serial: take termios_rwsem for ->rs485_config() & pass termios as param
@ 2022-06-20 6:40 ` Ilpo Järvinen
0 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Andy Shevchenko,
Vladimir Zapolskiy, Russell King, Richard Genoud, Nicolas Ferre,
Alexandre Belloni, Claudiu Beznea, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
Maxime Coquelin, Alexandre Torgue, linux-kernel, linux-arm-kernel,
linux-stm32
Cc: Lukas Wunner, Uwe Kleine-König, Lino Sanfilippo,
Ilpo Järvinen
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250.h | 3 ++-
drivers/tty/serial/8250/8250_dwlib.c | 3 ++-
drivers/tty/serial/8250/8250_exar.c | 9 +++++----
drivers/tty/serial/8250/8250_fintek.c | 2 +-
drivers/tty/serial/8250/8250_lpc18xx.c | 2 +-
drivers/tty/serial/8250/8250_pci.c | 2 +-
drivers/tty/serial/8250/8250_port.c | 3 ++-
drivers/tty/serial/amba-pl011.c | 2 +-
drivers/tty/serial/ar933x_uart.c | 2 +-
drivers/tty/serial/atmel_serial.c | 2 +-
drivers/tty/serial/fsl_lpuart.c | 4 ++--
drivers/tty/serial/imx.c | 2 +-
drivers/tty/serial/max310x.c | 2 +-
drivers/tty/serial/mcf.c | 3 ++-
drivers/tty/serial/omap-serial.c | 3 ++-
drivers/tty/serial/sc16is7xx.c | 2 +-
drivers/tty/serial/serial_core.c | 14 ++++++++++----
drivers/tty/serial/stm32-usart.c | 2 +-
include/linux/serial_core.h | 1 +
19 files changed, 38 insertions(+), 25 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 5cc967fe3b59..287153d32536 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -203,7 +203,8 @@ void serial8250_rpm_put(struct uart_8250_port *p);
void serial8250_rpm_get_tx(struct uart_8250_port *p);
void serial8250_rpm_put_tx(struct uart_8250_port *p);
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485);
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485);
void serial8250_em485_start_tx(struct uart_8250_port *p);
void serial8250_em485_stop_tx(struct uart_8250_port *p);
void serial8250_em485_destroy(struct uart_8250_port *p);
diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
index c83e7eaf3877..d1ff3daeb0ba 100644
--- a/drivers/tty/serial/8250/8250_dwlib.c
+++ b/drivers/tty/serial/8250/8250_dwlib.c
@@ -85,7 +85,8 @@ void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios, struct
}
EXPORT_SYMBOL_GPL(dw8250_do_set_termios);
-static int dw8250_rs485_config(struct uart_port *p, struct serial_rs485 *rs485)
+static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
u32 tcr;
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 3d999eec4087..f5344cfe303c 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -112,7 +112,8 @@
struct exar8250;
struct exar8250_platform {
- int (*rs485_config)(struct uart_port *, struct serial_rs485 *);
+ int (*rs485_config)(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485);
const struct serial_rs485 *rs485_supported;
int (*register_gpio)(struct pci_dev *, struct uart_8250_port *);
void (*unregister_gpio)(struct uart_8250_port *);
@@ -409,7 +410,7 @@ static void xr17v35x_unregister_gpio(struct uart_8250_port *port)
port->port.private_data = NULL;
}
-static int generic_rs485_config(struct uart_port *port,
+static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -441,7 +442,7 @@ static const struct exar8250_platform exar8250_default_platform = {
.rs485_supported = &generic_rs485_supported,
};
-static int iot2040_rs485_config(struct uart_port *port,
+static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
@@ -471,7 +472,7 @@ static int iot2040_rs485_config(struct uart_port *port,
value |= mode;
writeb(value, p + UART_EXAR_MPIOLVL_7_0);
- return generic_rs485_config(port, rs485);
+ return generic_rs485_config(port, termios, rs485);
}
static const struct serial_rs485 iot2040_rs485_supported = {
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 1fb86c73786c..eea693f5b577 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -191,7 +191,7 @@ static int fintek_8250_get_ldn_range(struct fintek_8250 *pdata, int *min,
return -ENODEV;
}
-static int fintek_8250_rs485_config(struct uart_port *port,
+static int fintek_8250_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
uint8_t config = 0;
diff --git a/drivers/tty/serial/8250/8250_lpc18xx.c b/drivers/tty/serial/8250/8250_lpc18xx.c
index 3a1cb51cbc91..d7cb3bb52069 100644
--- a/drivers/tty/serial/8250/8250_lpc18xx.c
+++ b/drivers/tty/serial/8250/8250_lpc18xx.c
@@ -32,7 +32,7 @@ struct lpc18xx_uart_data {
int line;
};
-static int lpc18xx_rs485_config(struct uart_port *port,
+static int lpc18xx_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct uart_8250_port *up = up_to_u8250p(port);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index b6d71268aa7d..d31d2350a9db 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1553,7 +1553,7 @@ pci_brcm_trumanage_setup(struct serial_private *priv,
#define FINTEK_RTS_INVERT BIT(5)
/* We should do proper H/W transceiver setting before change to RS485 mode */
-static int pci_fintek_rs485_config(struct uart_port *port,
+static int pci_fintek_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct pci_dev *pci_dev = to_pci_dev(port->dev);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 19c612d732cf..5cb3673f9ee5 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -664,7 +664,8 @@ EXPORT_SYMBOL_GPL(serial8250_em485_supported);
* if the uart is incapable of driving RTS as a Transmit Enable signal in
* hardware, relying on software emulation instead.
*/
-int serial8250_em485_config(struct uart_port *port, struct serial_rs485 *rs485)
+int serial8250_em485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
struct uart_8250_port *up = up_to_u8250p(port);
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index eccd66625d25..c8f52945a4aa 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -2197,7 +2197,7 @@ static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
return ret;
}
-static int pl011_rs485_config(struct uart_port *port,
+static int pl011_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct uart_amba_port *uap =
diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index ab2c5b2a1ce8..b73ce13683db 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -580,7 +580,7 @@ static const struct uart_ops ar933x_uart_ops = {
.verify_port = ar933x_uart_verify_port,
};
-static int ar933x_config_rs485(struct uart_port *port,
+static int ar933x_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct ar933x_uart_port *up =
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 74dd1d3ac46f..64dd6fea0a30 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -285,7 +285,7 @@ static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
}
/* Enable or disable the rs485 support */
-static int atmel_config_rs485(struct uart_port *port,
+static int atmel_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index d35414cb3e4e..8fe0494d4057 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1355,7 +1355,7 @@ static void lpuart_dma_rx_free(struct uart_port *port)
sport->dma_rx_cookie = -EINVAL;
}
-static int lpuart_config_rs485(struct uart_port *port,
+static int lpuart_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct lpuart_port *sport = container_of(port,
@@ -1385,7 +1385,7 @@ static int lpuart_config_rs485(struct uart_port *port,
return 0;
}
-static int lpuart32_config_rs485(struct uart_port *port,
+static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct lpuart_port *sport = container_of(port,
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index f4edde54175f..3457006cea3f 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1907,7 +1907,7 @@ static void imx_uart_poll_put_char(struct uart_port *port, unsigned char c)
#endif
/* called with port.lock taken and irqs off or from .probe without locking */
-static int imx_uart_rs485_config(struct uart_port *port,
+static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct imx_port *sport = (struct imx_port *)port;
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index d7d1791fcb57..5a8521fb9237 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -1026,7 +1026,7 @@ static void max310x_rs_proc(struct work_struct *ws)
MAX310X_MODE2_ECHOSUPR_BIT, mode2);
}
-static int max310x_rs485_config(struct uart_port *port,
+static int max310x_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct max310x_one *one = to_max310x_port(port);
diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c
index 036f178e3d66..73c5287b8e5e 100644
--- a/drivers/tty/serial/mcf.c
+++ b/drivers/tty/serial/mcf.c
@@ -431,7 +431,8 @@ static int mcf_verify_port(struct uart_port *port, struct serial_struct *ser)
/****************************************************************************/
/* Enable or disable the RS485 support */
-static int mcf_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+static int mcf_config_rs485(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
unsigned char mr1, mr2;
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 98622c35d896..1d1e48ff33d8 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1325,7 +1325,8 @@ static inline void serial_omap_add_console_port(struct uart_omap_port *up)
/* Enable or disable the rs485 support */
static int
-serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
+serial_omap_config_rs485(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned int mode;
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 2ceecaa4a478..8cb92a3b3fb8 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1127,7 +1127,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
spin_unlock_irqrestore(&port->lock, flags);
}
-static int sc16is7xx_config_rs485(struct uart_port *port,
+static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 621fc15e2e54..44c3785445e3 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1359,7 +1359,7 @@ int uart_rs485_config(struct uart_port *port)
uart_sanitize_serial_rs485(port, rs485);
- ret = port->rs485_config(port, rs485);
+ ret = port->rs485_config(port, NULL, rs485);
if (ret)
memset(rs485, 0, sizeof(*rs485));
@@ -1383,7 +1383,7 @@ static int uart_get_rs485_config(struct uart_port *port,
return 0;
}
-static int uart_set_rs485_config(struct uart_port *port,
+static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port,
struct serial_rs485 __user *rs485_user)
{
struct serial_rs485 rs485;
@@ -1402,7 +1402,7 @@ static int uart_set_rs485_config(struct uart_port *port,
uart_sanitize_serial_rs485(port, &rs485);
spin_lock_irqsave(&port->lock, flags);
- ret = port->rs485_config(port, &rs485);
+ ret = port->rs485_config(port, &tty->termios, &rs485);
if (!ret)
port->rs485 = rs485;
spin_unlock_irqrestore(&port->lock, flags);
@@ -1511,6 +1511,10 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
if (ret != -ENOIOCTLCMD)
goto out;
+ /* rs485_config requires more locking than others */
+ if (cmd == TIOCGRS485)
+ down_write(&tty->termios_rwsem);
+
mutex_lock(&port->mutex);
uport = uart_port_check(state);
@@ -1534,7 +1538,7 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
break;
case TIOCSRS485:
- ret = uart_set_rs485_config(uport, uarg);
+ ret = uart_set_rs485_config(tty, uport, uarg);
break;
case TIOCSISO7816:
@@ -1551,6 +1555,8 @@ uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
}
out_up:
mutex_unlock(&port->mutex);
+ if (cmd == TIOCGRS485)
+ up_write(&tty->termios_rwsem);
out:
return ret;
}
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index db3dd9731ee1..13992e64a7df 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -97,7 +97,7 @@ static void stm32_usart_config_reg_rs485(u32 *cr1, u32 *cr3, u32 delay_ADE,
*cr1 |= rs485_deat_dedt;
}
-static int stm32_usart_config_rs485(struct uart_port *port,
+static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485conf)
{
struct stm32_port *stm32_port = to_stm32_port(port);
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 5518b70177b3..17bbd0412a23 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -132,6 +132,7 @@ struct uart_port {
unsigned int old);
void (*handle_break)(struct uart_port *);
int (*rs485_config)(struct uart_port *,
+ struct ktermios *termios,
struct serial_rs485 *rs485);
int (*iso7816_config)(struct uart_port *,
struct serial_iso7816 *iso7816);
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
` (3 preceding siblings ...)
2022-06-20 6:40 ` Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
2022-06-20 10:58 ` Andy Shevchenko
2022-06-20 6:40 ` [PATCH v8 6/6] serial: 8250_dwlib: Support for 9th bit multipoint addressing Ilpo Järvinen
5 siblings, 1 reply; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Jonathan Corbet, Arnd Bergmann,
linux-doc, linux-kernel, linux-arch
Cc: Andy Shevchenko, Lukas Wunner, Uwe Kleine-König,
Lino Sanfilippo, Ilpo Järvinen, linux-api
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
The changes to serial_rs485 struct were test built with a few traps to
detect mislayouting on archs lkp/0day builts for (all went fine):
BUILD_BUG_ON(((&rs485.delay_rts_after_send) + 1) != &rs485.padding[0]);
BUILD_BUG_ON(&rs485.padding[1] != &rs485.padding1[0]);
BUILD_BUG_ON(sizeof(rs485) != ((u8 *)(&rs485.padding[4]) -
((u8 *)&rs485.flags) + sizeof(__u32)));
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arch@vger.kernel.org
---
Documentation/driver-api/serial/driver.rst | 2 ++
.../driver-api/serial/serial-rs485.rst | 26 ++++++++++++++++++-
drivers/tty/serial/serial_core.c | 14 +++++++++-
drivers/tty/tty_ioctl.c | 4 +++
include/uapi/asm-generic/termbits-common.h | 1 +
include/uapi/linux/serial.h | 20 ++++++++++++--
6 files changed, 63 insertions(+), 4 deletions(-)
diff --git a/Documentation/driver-api/serial/driver.rst b/Documentation/driver-api/serial/driver.rst
index 7ef83fd3917b..35fb3866bb3d 100644
--- a/Documentation/driver-api/serial/driver.rst
+++ b/Documentation/driver-api/serial/driver.rst
@@ -261,6 +261,8 @@ hardware.
- parity enable
PARODD
- odd parity (when PARENB is in force)
+ ADDRB
+ - address bit (changed through .rs485_config()).
CREAD
- enable reception of characters (if not set,
still receive characters from the port, but
diff --git a/Documentation/driver-api/serial/serial-rs485.rst b/Documentation/driver-api/serial/serial-rs485.rst
index 00b5d333acba..6ebad75c74ed 100644
--- a/Documentation/driver-api/serial/serial-rs485.rst
+++ b/Documentation/driver-api/serial/serial-rs485.rst
@@ -99,7 +99,31 @@ RS485 Serial Communications
/* Error handling. See errno. */
}
-5. References
+5. Multipoint Addressing
+========================
+
+ The Linux kernel provides addressing mode for multipoint RS-485 serial
+ communications line. The addressing mode is enabled with SER_RS485_ADDRB
+ flag in serial_rs485. Struct serial_rs485 has two additional flags and
+ fields for enabling receive and destination addresses.
+
+ Address mode flags:
+ - SER_RS485_ADDRB: Enabled addressing mode (sets also ADDRB in termios).
+ - SER_RS485_ADDR_RECV: Receive (filter) address enabled.
+ - SER_RS485_ADDR_DEST: Set destination address.
+
+ Address fields (enabled with corresponding SER_RS485_ADDR_* flag):
+ - addr_recv: Receive address.
+ - addr_dest: Destination address.
+
+ Once a receive address is set, the communication can occur only with the
+ particular device and other peers are filtered out. It is left up to the
+ receiver side to enforce the filtering. Receive address will be cleared
+ if SER_RS485_ADDR_RECV is not set.
+
+ Note: not all devices supporting RS485 support multipoint addressing.
+
+6. References
=============
[1] include/uapi/linux/serial.h
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 44c3785445e3..414099e3262a 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1294,6 +1294,17 @@ static int uart_check_rs485_flags(struct uart_port *port, struct serial_rs485 *r
if (flags & ~port->rs485_supported->flags)
return -EINVAL;
+ /* Asking for address w/o addressing mode? */
+ if (!(rs485->flags & SER_RS485_ADDRB) &&
+ (rs485->flags & (SER_RS485_ADDR_RECV|SER_RS485_ADDR_DEST)))
+ return -EINVAL;
+
+ /* Address given but not enabled? */
+ if (!(rs485->flags & SER_RS485_ADDR_RECV) && rs485->addr_recv)
+ return -EINVAL;
+ if (!(rs485->flags & SER_RS485_ADDR_DEST) && rs485->addr_dest)
+ return -EINVAL;
+
return 0;
}
@@ -1349,7 +1360,8 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4
rs485->flags &= supported_flags;
/* Return clean padding area to userspace */
- memset(rs485->padding, 0, sizeof(rs485->padding));
+ memset(rs485->padding0, 0, sizeof(rs485->padding0));
+ memset(rs485->padding1, 0, sizeof(rs485->padding1));
}
int uart_rs485_config(struct uart_port *port)
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index adae687f654b..ed253f2337a7 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -319,6 +319,8 @@ unsigned char tty_get_frame_size(unsigned int cflag)
bits++;
if (cflag & PARENB)
bits++;
+ if (cflag & ADDRB)
+ bits++;
return bits;
}
@@ -353,6 +355,8 @@ int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios)
old_termios = tty->termios;
tty->termios = *new_termios;
unset_locked_termios(tty, &old_termios);
+ /* Reset any ADDRB changes, ADDRB is changed through ->rs485_config() */
+ tty->termios.c_cflag ^= (tty->termios.c_cflag ^ old_termios.c_cflag) & ADDRB;
if (tty->ops->set_termios)
tty->ops->set_termios(tty, &old_termios);
diff --git a/include/uapi/asm-generic/termbits-common.h b/include/uapi/asm-generic/termbits-common.h
index 4d084fe8def5..4a6a79f28b21 100644
--- a/include/uapi/asm-generic/termbits-common.h
+++ b/include/uapi/asm-generic/termbits-common.h
@@ -46,6 +46,7 @@ typedef unsigned int speed_t;
#define EXTA B19200
#define EXTB B38400
+#define ADDRB 0x20000000 /* address bit */
#define CMSPAR 0x40000000 /* mark or space (stick) parity */
#define CRTSCTS 0x80000000 /* flow control */
diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h
index fa6b16e5fdd8..c4c75fd7037e 100644
--- a/include/uapi/linux/serial.h
+++ b/include/uapi/linux/serial.h
@@ -126,10 +126,26 @@ struct serial_rs485 {
#define SER_RS485_TERMINATE_BUS (1 << 5) /* Enable bus
termination
(if supported) */
+
+/* RS-485 addressing mode */
+#define SER_RS485_ADDRB (1 << 6) /* Enable addressing mode */
+#define SER_RS485_ADDR_RECV (1 << 7) /* Receive address filter */
+#define SER_RS485_ADDR_DEST (1 << 8) /* Destination address */
+
__u32 delay_rts_before_send; /* Delay before send (milliseconds) */
__u32 delay_rts_after_send; /* Delay after send (milliseconds) */
- __u32 padding[5]; /* Memory is cheap, new structs
- are a royal PITA .. */
+ union {
+ /* v1 */
+ __u32 padding[5]; /* Memory is cheap, new structs are a pain */
+
+ /* v2 (adds addressing mode fields) */
+ struct {
+ __u8 addr_recv;
+ __u8 addr_dest;
+ __u8 padding0[2];
+ __u32 padding1[4];
+ };
+ };
};
/*
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses
2022-06-20 6:40 ` [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses Ilpo Järvinen
@ 2022-06-20 10:58 ` Andy Shevchenko
2022-06-20 11:26 ` Ilpo Järvinen
0 siblings, 1 reply; 11+ messages in thread
From: Andy Shevchenko @ 2022-06-20 10:58 UTC (permalink / raw)
To: Ilpo Järvinen
Cc: linux-serial, Greg KH, Jiri Slaby, Jonathan Corbet, Arnd Bergmann,
linux-doc, linux-kernel, linux-arch, Lukas Wunner,
Uwe Kleine-König, Lino Sanfilippo, linux-api
On Mon, Jun 20, 2022 at 09:40:29AM +0300, Ilpo Järvinen wrote:
> Add support for RS-485 multipoint addressing using 9th bit [*]. The
> addressing mode is configured through ->rs485_config().
>
> ADDRB in termios indicates 9th bit addressing mode is enabled. In this
> mode, 9th bit is used to indicate an address (byte) within the
> communication line. ADDRB can only be enabled/disabled through
> ->rs485_config() that is also responsible for setting the destination and
> receiver (filter) addresses.
> The changes to serial_rs485 struct were test built with a few traps to
> detect mislayouting on archs lkp/0day builts for (all went fine):
> BUILD_BUG_ON(((&rs485.delay_rts_after_send) + 1) != &rs485.padding[0]);
> BUILD_BUG_ON(&rs485.padding[1] != &rs485.padding1[0]);
> BUILD_BUG_ON(sizeof(rs485) != ((u8 *)(&rs485.padding[4]) -
> ((u8 *)&rs485.flags) + sizeof(__u32)));
You may add static_asserts() for the above mentioned cases.
> [*] Technically, RS485 is just an electronic spec and does not itself
> specify the 9th bit addressing mode but 9th bit seems at least
> "semi-standard" way to do addressing with RS485.
...
> - __u32 padding[5]; /* Memory is cheap, new structs
> - are a royal PITA .. */
> + union {
> + /* v1 */
> + __u32 padding[5]; /* Memory is cheap, new structs are a pain */
> +
> + /* v2 (adds addressing mode fields) */
How user space will inform a kernel that it's trying v2?
Usually when we have a union, it should be accompanied with the enum or version
or something to tell which part of it is in use. I can imagine that in this case
it's implied by the IOCTL parameters that never should be used on a garbage.
Either add a commit message / UAPI comment or add a version field or ...?
> + struct {
> + __u8 addr_recv;
> + __u8 addr_dest;
> + __u8 padding0[2];
> + __u32 padding1[4];
> + };
> + };
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses
2022-06-20 10:58 ` Andy Shevchenko
@ 2022-06-20 11:26 ` Ilpo Järvinen
2022-06-20 11:48 ` Andy Shevchenko
0 siblings, 1 reply; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 11:26 UTC (permalink / raw)
To: Andy Shevchenko
Cc: linux-serial, Greg KH, Jiri Slaby, Jonathan Corbet, Arnd Bergmann,
linux-doc, LKML, linux-arch, Lukas Wunner, Uwe Kleine-König,
Lino Sanfilippo, linux-api
[-- Attachment #1: Type: text/plain, Size: 2279 bytes --]
On Mon, 20 Jun 2022, Andy Shevchenko wrote:
> On Mon, Jun 20, 2022 at 09:40:29AM +0300, Ilpo Järvinen wrote:
> > Add support for RS-485 multipoint addressing using 9th bit [*]. The
> > addressing mode is configured through ->rs485_config().
> >
> > ADDRB in termios indicates 9th bit addressing mode is enabled. In this
> > mode, 9th bit is used to indicate an address (byte) within the
> > communication line. ADDRB can only be enabled/disabled through
> > ->rs485_config() that is also responsible for setting the destination and
> > receiver (filter) addresses.
>
> > The changes to serial_rs485 struct were test built with a few traps to
> > detect mislayouting on archs lkp/0day builts for (all went fine):
> > BUILD_BUG_ON(((&rs485.delay_rts_after_send) + 1) != &rs485.padding[0]);
> > BUILD_BUG_ON(&rs485.padding[1] != &rs485.padding1[0]);
> > BUILD_BUG_ON(sizeof(rs485) != ((u8 *)(&rs485.padding[4]) -
> > ((u8 *)&rs485.flags) + sizeof(__u32)));
>
> You may add static_asserts() for the above mentioned cases.
I'll add into the end of serial_core.h but in a cleaned up form
using offsetof(). Those above look rather ugly :-).
> > [*] Technically, RS485 is just an electronic spec and does not itself
> > specify the 9th bit addressing mode but 9th bit seems at least
> > "semi-standard" way to do addressing with RS485.
>
> ...
>
> > - __u32 padding[5]; /* Memory is cheap, new structs
> > - are a royal PITA .. */
> > + union {
> > + /* v1 */
> > + __u32 padding[5]; /* Memory is cheap, new structs are a pain */
> > +
> > + /* v2 (adds addressing mode fields) */
>
> How user space will inform a kernel that it's trying v2?
>
> Usually when we have a union, it should be accompanied with the enum or version
> or something to tell which part of it is in use. I can imagine that in this case
> it's implied by the IOCTL parameters that never should be used on a garbage.
>
> Either add a commit message / UAPI comment or add a version field or ...?
>
> > + struct {
> > + __u8 addr_recv;
> > + __u8 addr_dest;
The flags in .flags indicate when these two new fields are in use. Do you
think I need something beyond that. Maybe I should remove those comments
so they don't mislead you to think it's a "version" for real?
--
i.
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses
2022-06-20 11:26 ` Ilpo Järvinen
@ 2022-06-20 11:48 ` Andy Shevchenko
0 siblings, 0 replies; 11+ messages in thread
From: Andy Shevchenko @ 2022-06-20 11:48 UTC (permalink / raw)
To: Ilpo Järvinen
Cc: linux-serial, Greg KH, Jiri Slaby, Jonathan Corbet, Arnd Bergmann,
linux-doc, LKML, linux-arch, Lukas Wunner, Uwe Kleine-König,
Lino Sanfilippo, linux-api
On Mon, Jun 20, 2022 at 02:26:17PM +0300, Ilpo Järvinen wrote:
> On Mon, 20 Jun 2022, Andy Shevchenko wrote:
> > On Mon, Jun 20, 2022 at 09:40:29AM +0300, Ilpo Järvinen wrote:
...
> > > The changes to serial_rs485 struct were test built with a few traps to
> > > detect mislayouting on archs lkp/0day builts for (all went fine):
> > > BUILD_BUG_ON(((&rs485.delay_rts_after_send) + 1) != &rs485.padding[0]);
> > > BUILD_BUG_ON(&rs485.padding[1] != &rs485.padding1[0]);
> > > BUILD_BUG_ON(sizeof(rs485) != ((u8 *)(&rs485.padding[4]) -
> > > ((u8 *)&rs485.flags) + sizeof(__u32)));
> >
> > You may add static_asserts() for the above mentioned cases.
>
> I'll add into the end of serial_core.h but in a cleaned up form
> using offsetof(). Those above look rather ugly :-).
Agree!
...
> > > - __u32 padding[5]; /* Memory is cheap, new structs
> > > - are a royal PITA .. */
> > > + union {
> > > + /* v1 */
> > > + __u32 padding[5]; /* Memory is cheap, new structs are a pain */
> > > +
> > > + /* v2 (adds addressing mode fields) */
> >
> > How user space will inform a kernel that it's trying v2?
> >
> > Usually when we have a union, it should be accompanied with the enum or version
> > or something to tell which part of it is in use. I can imagine that in this case
> > it's implied by the IOCTL parameters that never should be used on a garbage.
> >
> > Either add a commit message / UAPI comment or add a version field or ...?
> >
> > > + struct {
> > > + __u8 addr_recv;
> > > + __u8 addr_dest;
>
> The flags in .flags indicate when these two new fields are in use. Do you
> think I need something beyond that. Maybe I should remove those comments
> so they don't mislead you to think it's a "version" for real?
Yes, either drop this versioning, or replace with a comment on top of a union
like:
/* The fields are defined by flags */
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v8 6/6] serial: 8250_dwlib: Support for 9th bit multipoint addressing
2022-06-20 6:40 [PATCH v8 0/6] Add RS485 9th bit addressing mode support to DW UART Ilpo Järvinen
` (4 preceding siblings ...)
2022-06-20 6:40 ` [PATCH v8 5/6] serial: Support for RS-485 multipoint addresses Ilpo Järvinen
@ 2022-06-20 6:40 ` Ilpo Järvinen
5 siblings, 0 replies; 11+ messages in thread
From: Ilpo Järvinen @ 2022-06-20 6:40 UTC (permalink / raw)
To: linux-serial, Greg KH, Jiri Slaby, Andy Shevchenko, linux-kernel
Cc: Lukas Wunner, Uwe Kleine-König, Lino Sanfilippo,
Ilpo Järvinen, Heikki Krogerus, Raymond Tan,
Lakshmi Sowjanya
Add 9th bit multipoint addressing mode for DW UART. 9th bit addressing
can be used only when HW RS485 is available.
Updating RAR (receive address register) is bit tricky because busy
indication is not be available when DW UART is strictly 16550
compatible, which is the case with the hardware I was testing with. RAR
should not be updated while receive is in progress which is now
achieved by deasserting RE and waiting for one frame (in case rx would
be in progress, the driver seems to have no way of knowing it w/o busy
indication). Because of this complexity, it's better to avoid doing it
unless really needed.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_dwlib.c | 102 ++++++++++++++++++++++++++-
1 file changed, 101 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
index d1ff3daeb0ba..da330ef46446 100644
--- a/drivers/tty/serial/8250/8250_dwlib.c
+++ b/drivers/tty/serial/8250/8250_dwlib.c
@@ -3,8 +3,10 @@
#include <linux/bitops.h>
#include <linux/bitfield.h>
+#include <linux/delay.h>
#include <linux/device.h>
#include <linux/kernel.h>
+#include <linux/math.h>
#include <linux/property.h>
#include <linux/serial_8250.h>
#include <linux/serial_core.h>
@@ -16,9 +18,18 @@
#define DW_UART_DE_EN 0xb0 /* Driver Output Enable Register */
#define DW_UART_RE_EN 0xb4 /* Receiver Output Enable Register */
#define DW_UART_DLF 0xc0 /* Divisor Latch Fraction Register */
+#define DW_UART_RAR 0xc4 /* Receive Address Register */
+#define DW_UART_TAR 0xc8 /* Transmit Address Register */
+#define DW_UART_LCR_EXT 0xcc /* Line Extended Control Register */
#define DW_UART_CPR 0xf4 /* Component Parameter Register */
#define DW_UART_UCV 0xf8 /* UART Component Version */
+/* Receive / Transmit Address Register bits */
+#define DW_UART_ADDR_MASK GENMASK(7, 0)
+
+/* Line Status Register bits */
+#define DW_UART_LSR_ADDR_RCVD BIT(8)
+
/* Transceiver Control Register bits */
#define DW_UART_TCR_RS485_EN BIT(0)
#define DW_UART_TCR_RE_POL BIT(1)
@@ -28,6 +39,12 @@
#define DW_UART_TCR_XFER_MODE_SW_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 1)
#define DW_UART_TCR_XFER_MODE_DE_OR_RE FIELD_PREP(DW_UART_TCR_XFER_MODE, 2)
+/* Line Extended Control Register bits */
+#define DW_UART_LCR_EXT_DLS_E BIT(0)
+#define DW_UART_LCR_EXT_ADDR_MATCH BIT(1)
+#define DW_UART_LCR_EXT_SEND_ADDR BIT(2)
+#define DW_UART_LCR_EXT_TRANSMIT_MODE BIT(3)
+
/* Component Parameter Register bits */
#define DW_UART_CPR_ABP_DATA_WIDTH (3 << 0)
#define DW_UART_CPR_AFCE_MODE (1 << 4)
@@ -82,9 +99,83 @@ void dw8250_do_set_termios(struct uart_port *p, struct ktermios *termios, struct
p->status |= UPSTAT_AUTOCTS;
serial8250_do_set_termios(p, termios, old);
+
+ /* Filter addresses which have 9th bit set */
+ p->ignore_status_mask |= DW_UART_LSR_ADDR_RCVD;
+ p->read_status_mask |= DW_UART_LSR_ADDR_RCVD;
}
EXPORT_SYMBOL_GPL(dw8250_do_set_termios);
+/*
+ * Wait until re is de-asserted for sure. An ongoing receive will keep
+ * re asserted until end of frame. Without BUSY indication available,
+ * only available course of action is to wait for the time it takes to
+ * receive one frame (there might nothing to receive but w/o BUSY the
+ * driver cannot know).
+ */
+static void dw8250_wait_re_deassert(struct uart_port *p)
+{
+ ndelay(p->frame_time);
+}
+
+static void dw8250_update_rar(struct uart_port *p, u32 addr)
+{
+ u32 re_en = dw8250_readl_ext(p, DW_UART_RE_EN);
+
+ /*
+ * RAR shouldn't be changed while receiving. Thus, de-assert RE_EN
+ * if asserted and wait.
+ */
+ if (re_en)
+ dw8250_writel_ext(p, DW_UART_RE_EN, 0);
+ dw8250_wait_re_deassert(p);
+ dw8250_writel_ext(p, DW_UART_RAR, addr);
+ if (re_en)
+ dw8250_writel_ext(p, DW_UART_RE_EN, re_en);
+}
+
+static void dw8250_rs485_set_addr(struct uart_port *p, struct serial_rs485 *rs485,
+ struct ktermios *termios)
+{
+ u32 lcr = dw8250_readl_ext(p, DW_UART_LCR_EXT);
+
+ if (rs485->flags & SER_RS485_ADDRB) {
+ lcr |= DW_UART_LCR_EXT_DLS_E;
+ if (termios)
+ termios->c_cflag |= ADDRB;
+
+ if (rs485->flags & SER_RS485_ADDR_RECV) {
+ u32 delta = p->rs485.flags ^ rs485->flags;
+
+ /*
+ * rs485 (param) is equal to uart_port's rs485 only during init
+ * (during init, delta is not yet applicable).
+ */
+ if (unlikely(&p->rs485 == rs485))
+ delta = rs485->flags;
+
+ if ((delta & SER_RS485_ADDR_RECV) ||
+ (p->rs485.addr_recv != rs485->addr_recv))
+ dw8250_update_rar(p, rs485->addr_recv);
+ lcr |= DW_UART_LCR_EXT_ADDR_MATCH;
+ } else {
+ lcr &= ~DW_UART_LCR_EXT_ADDR_MATCH;
+ }
+ if (rs485->flags & SER_RS485_ADDR_DEST) {
+ /*
+ * Don't skip writes here as another endpoint could
+ * have changed communication line's destination
+ * address in between.
+ */
+ dw8250_writel_ext(p, DW_UART_TAR, rs485->addr_dest);
+ lcr |= DW_UART_LCR_EXT_SEND_ADDR;
+ }
+ } else {
+ lcr = 0;
+ }
+ dw8250_writel_ext(p, DW_UART_LCR_EXT, lcr);
+}
+
static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
struct serial_rs485 *rs485)
{
@@ -109,6 +200,9 @@ static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
dw8250_writel_ext(p, DW_UART_DE_EN, 1);
dw8250_writel_ext(p, DW_UART_RE_EN, 1);
} else {
+ if (termios)
+ termios->c_cflag &= ~ADDRB;
+
tcr &= ~DW_UART_TCR_RS485_EN;
}
@@ -123,6 +217,10 @@ static int dw8250_rs485_config(struct uart_port *p, struct ktermios *termios,
dw8250_writel_ext(p, DW_UART_TCR, tcr);
+ /* Addressing mode can only be set up after TCR */
+ if (rs485->flags & SER_RS485_ENABLED)
+ dw8250_rs485_set_addr(p, rs485, termios);
+
return 0;
}
@@ -142,7 +240,8 @@ static bool dw8250_detect_rs485_hw(struct uart_port *p)
static const struct serial_rs485 dw8250_rs485_supported = {
.flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_RTS_ON_SEND |
- SER_RS485_RTS_AFTER_SEND,
+ SER_RS485_RTS_AFTER_SEND | SER_RS485_ADDRB | SER_RS485_ADDR_RECV |
+ SER_RS485_ADDR_DEST,
};
void dw8250_setup_port(struct uart_port *p)
@@ -155,6 +254,7 @@ void dw8250_setup_port(struct uart_port *p)
pd->hw_rs485_support = dw8250_detect_rs485_hw(p);
if (pd->hw_rs485_support) {
p->rs485_config = dw8250_rs485_config;
+ up->lsr_save_mask = LSR_SAVE_FLAGS | DW_UART_LSR_ADDR_RCVD;
p->rs485_supported = &dw8250_rs485_supported;
} else {
p->rs485_config = serial8250_em485_config;
--
2.30.2
^ permalink raw reply related [flat|nested] 11+ messages in thread