Re: [PATCH v5 23/23] gpu: nova-core: load and run FWSEC-FRTS

[Danilo Krummrich <dakr@kernel.org>]

On Thu, Jun 12, 2025 at 11:01:51PM +0900, Alexandre Courbot wrote:
> @@ -237,6 +237,67 @@ pub(crate) fn new(
>              },
>          )?;
>  
> +        // Check that the WPR2 region does not already exists - if it does, the GPU needs to be
> +        // reset.
> +        if regs::NV_PFB_PRI_MMU_WPR2_ADDR_HI::read(bar).hi_val() != 0 {
> +            dev_err!(
> +                pdev.as_ref(),
> +                "WPR2 region already exists - GPU needs to be reset to proceed\n"
> +            );
> +            return Err(EBUSY);
> +        }
> +
> +        // Reset falcon, load FWSEC-FRTS, and run it.
> +        gsp_falcon
> +            .reset(bar)
> +            .inspect_err(|e| dev_err!(pdev.as_ref(), "Failed to reset GSP falcon: {:?}\n", e))?;
> +        gsp_falcon
> +            .dma_load(bar, &fwsec_frts)
> +            .inspect_err(|e| dev_err!(pdev.as_ref(), "Failed to load FWSEC-FRTS: {:?}\n", e))?;
> +        let (mbox0, _) = gsp_falcon
> +            .boot(bar, Some(0), None)
> +            .inspect_err(|e| dev_err!(pdev.as_ref(), "Failed to boot FWSEC-FRTS: {:?}\n", e))?;
> +        if mbox0 != 0 {
> +            dev_err!(pdev.as_ref(), "FWSEC firmware returned error {}\n", mbox0);
> +            return Err(EIO);
> +        }
> +
> +        // SCRATCH_E contains FWSEC-FRTS' error code, if any.
> +        let frts_status = regs::NV_PBUS_SW_SCRATCH_0E::read(bar).frts_err_code();
> +        if frts_status != 0 {
> +            dev_err!(
> +                pdev.as_ref(),
> +                "FWSEC-FRTS returned with error code {:#x}",
> +                frts_status
> +            );
> +            return Err(EIO);
> +        }
> +
> +        // Check the WPR2 has been created as we requested.
> +        let (wpr2_lo, wpr2_hi) = (
> +            (regs::NV_PFB_PRI_MMU_WPR2_ADDR_LO::read(bar).lo_val() as u64) << 12,
> +            (regs::NV_PFB_PRI_MMU_WPR2_ADDR_HI::read(bar).hi_val() as u64) << 12,
> +        );
> +        if wpr2_hi == 0 {
> +            dev_err!(
> +                pdev.as_ref(),
> +                "WPR2 region not created after running FWSEC-FRTS\n"
> +            );
> +
> +            return Err(EIO);
> +        } else if wpr2_lo != fb_layout.frts.start {
> +            dev_err!(
> +                pdev.as_ref(),
> +                "WPR2 region created at unexpected address {:#x}; expected {:#x}\n",
> +                wpr2_lo,
> +                fb_layout.frts.start,
> +            );
> +            return Err(EIO);
> +        }
> +
> +        dev_dbg!(pdev.as_ref(), "WPR2: {:#x}-{:#x}\n", wpr2_lo, wpr2_hi);
> +        dev_dbg!(pdev.as_ref(), "GPU instance built\n");
> +

This makes Gpu::new() quite messy, can we move this to a separate function
please?