Re: [PATCH 3/5] ARM: mach-imx: tzasc: add region configure helpers

[Sascha Hauer <s.hauer@pengutronix.de>]

On Thu, Jun 19, 2025 at 05:25:54PM +0200, Marco Felsch wrote:
> At the moment the TZC380 driver is very limited and focused on minimal
> platform setup unlike the TZC400 driver.
> 
> This commit adds helper functions to setup any number of TZASC regions
> of any size which is required by later commits to setup an early
> non-secure TZASC region1.
> 
> The code is based on the TZC400 barebox driver and the TZC380 OP-TEE
> driver.
> 
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
>  arch/arm/mach-imx/tzasc.c | 235 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 235 insertions(+)
> 
> diff --git a/arch/arm/mach-imx/tzasc.c b/arch/arm/mach-imx/tzasc.c
> index 4cb4d7c5cffc..4f6da6016601 100644
> --- a/arch/arm/mach-imx/tzasc.c
> +++ b/arch/arm/mach-imx/tzasc.c
> @@ -1,11 +1,76 @@
>  // SPDX-License-Identifier: GPL-2.0-only
>  
> +#define pr_fmt(fmt) "tzc380: " fmt
> +
> +#include <common.h>
>  #include <mach/imx/generic.h>
>  #include <mach/imx/tzasc.h>
> +#include <linux/bitfield.h>
>  #include <linux/bitops.h>
> +#include <linux/log2.h>
> +#include <linux/sizes.h>
>  #include <mach/imx/imx8m-regs.h>
>  #include <io.h>
>  
> +/*******************************************************************************
> + *                         TZC380 defines
> + ******************************************************************************/
> +
> +#define TZC380_BUILD_CONFIG		0x000
> +#define   TZC380_BUILD_CONFIG_AW	GENMASK(13, 8)
> +#define   TZC380_BUILD_CONFIG_NR	GENMASK(4, 0)
> +
> +/*
> + * All TZC region configuration registers are placed one after another. It
> + * depicts size of block of registers for programming each region.
> + */
> +#define TZC380_REGION_REG_SIZE		0x10
> +
> +#define TZC380_REGION_SETUP_LOW_0	0x100
> +#define TZC380_REGION_SETUP_HIGH_0	0x104
> +#define TZC380_REGION_ATTR_0		0x108
> +#define   TZC380_REGION_SP		GENMASK(31, 28)
> +#define   TZC380_SUBREGION_DIS_MASK	GENMASK(15, 8)
> +#define   TZC380_REGION_SIZE		GENMASK(6, 1)
> +#define   TZC380_REGION_EN		BIT(0)
> +
> +/* ID Registers */
> +#define TZC380_PID0_OFF			0xfe0
> +#define TZC380_PID1_OFF			0xfe4
> +#define   TZC380_PERIPHERAL_ID		0x380
> +#define TZC380_PID2_OFF			0xfe8
> +#define TZC380_PID3_OFF			0xfec
> +#define TZC380_PID4_OFF			0xfd0
> +#define TZC380_CID0_OFF			0xff0
> +#define TZC380_CID1_OFF			0xff4
> +#define TZC380_CID2_OFF			0xff8
> +
> +#define TZC380_REGION_OFFSET(region_no)		\
> +		(TZC380_REGION_REG_SIZE * (region_no))
> +#define TZC380_REGION_SETUP_LOW(region_no)	\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_SETUP_LOW_0)
> +#define TZC380_REGION_SETUP_HIGH(region_no)	\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_SETUP_HIGH_0)
> +#define TZC380_REGION_ATTR(region_no)		\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_ATTR_0)
> +
> +#define TZC380_REGION_SP_NS_W		FIELD_PREP(TZC380_REGION_SP, BIT(0))
> +#define TZC380_REGION_SP_NS_R		FIELD_PREP(TZC380_REGION_SP, BIT(1))
> +#define TZC380_REGION_SP_S_W		FIELD_PREP(TZC380_REGION_SP, BIT(2))
> +#define TZC380_REGION_SP_S_R		FIELD_PREP(TZC380_REGION_SP, BIT(3))
> +
> +#define TZC380_REGION_SP_ALL		\
> +		(TZC380_REGION_SP_NS_W | TZC380_REGION_SP_NS_R | \
> +		 TZC380_REGION_SP_S_W | TZC380_REGION_SP_S_R)
> +#define TZC380_REGION_SP_S_RW		\
> +		(TZC380_REGION_SP_S_W | TZC380_REGION_SP_S_R)
> +#define TZC380_REGION_SP_NS_RW		\
> +		(TZC380_REGION_SP_NS_W | TZC380_REGION_SP_NS_R)
> +
> +/*******************************************************************************
> + *                         SoC specific defines
> + ******************************************************************************/
> +
>  #define GPR_TZASC_EN					BIT(0)
>  #define GPR_TZASC_ID_SWAP_BYPASS		BIT(1)
>  #define GPR_TZASC_EN_LOCK				BIT(16)
> @@ -14,6 +79,176 @@
>  #define MX8M_TZASC_REGION_ATTRIBUTES_0		(MX8M_TZASC_BASE_ADDR + 0x108)
>  #define MX8M_TZASC_REGION_ATTRIBUTES_0_SP	GENMASK(31, 28)
>  
> +/*
> + * Implementation defined values used to validate inputs later.
> + * Filters : max of 4 ; 0 to 3
> + * Regions : max of 9 ; 0 to 8
> + * Address width : Values between 32 to 64
> + */
> +struct tzc380_instance {
> +	void __iomem *base;
> +	uint8_t addr_width;
> +	uint8_t num_regions;
> +};
> +/* Some platforms like i.MX6 does have two tzc380 controllers */
> +static struct tzc380_instance tzc380_inst[2];
> +
> +static inline unsigned int tzc_read_peripheral_id(void __iomem *base)
> +{
> +	unsigned int id;
> +
> +	id = in_le32(base + TZC380_PID0_OFF);
> +	/* Masks DESC part in PID1 */
> +	id |= ((in_le32(base + TZC380_PID1_OFF) & 0xFU) << 8U);
> +
> +	return id;
> +}
> +
> +static struct tzc380_instance *tzc380_init(void __iomem *base)
> +{
> +	struct tzc380_instance *tzc380 = &tzc380_inst[0];
> +	unsigned int tzc380_id;
> +	unsigned int tzc380_build;
> +
> +	if (tzc380->base)
> +		tzc380 = &tzc380_inst[1];
> +
> +	if (tzc380->base)
> +		panic("TZC-380: No free memory\n");
> +
> +	tzc380->base = base;
> +
> +	tzc380_id = tzc_read_peripheral_id(base);
> +	if (tzc380_id != TZC380_PERIPHERAL_ID)
> +		panic("TZC-380 : Wrong device ID (0x%x).\n", tzc380_id);
> +
> +	/* Save values we will use later. */
> +	tzc380_build = in_le32(base + TZC380_BUILD_CONFIG);
> +	tzc380->addr_width  = FIELD_GET(TZC380_BUILD_CONFIG_AW, tzc380_build) + 1;
> +	tzc380->num_regions = FIELD_GET(TZC380_BUILD_CONFIG_NR, tzc380_build) + 1;
> +
> +	return tzc380;
> +}
> +
> +static void
> +tzc380_configure_region(struct tzc380_instance *tzc380, unsigned int region,
> +			uint64_t region_base, unsigned int region_attr)
> +{
> +	void __iomem *base = tzc380->base;
> +
> +	/* Do range checks on regions */
> +	ASSERT((region < tzc380->num_regions));
> +
> +	pr_debug("TrustZone : Configuring region %u\n", region);

pr_fmt is already set, so this expands to "tzc380: TrustZone :" which
seems redundant. We should remove the "TrustZone :" No need to resend
just for that, I can fix it while applying.

Sascha

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |