From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Jiri Slaby <jirislaby@kernel.org>,
linux-serial@vger.kernel.org,
qianfan Zhao <qianfanguijin@163.com>,
Adriana Nicolae <adriana@arista.com>,
linux-kernel@vger.kernel.org, "Bandal,
Shankar" <shankar.bandal@intel.com>,
"Murthy, Shanth" <shanth.murthy@intel.com>,
stable@vger.kernel.org
Subject: Re: [PATCH v2 5/7] serial: 8250_dw: Rework IIR_NO_INT handling to stop interrupt storm
Date: Wed, 28 Jan 2026 16:03:55 +0200 [thread overview]
Message-ID: <aXoXSxsem4hOLlrO@smile.fi.intel.com> (raw)
In-Reply-To: <20260128105301.1869-6-ilpo.jarvinen@linux.intel.com>
On Wed, Jan 28, 2026 at 12:52:59PM +0200, Ilpo Järvinen wrote:
> INTC10EE UART can end up into an interrupt storm where it reports
> IIR_NO_INT (0x1). If the storm happens during active UART operation, it
> is promptly stopped by IIR value change due to Rx or Tx events.
> However, when there is no activity, either due to idle serial line or
> due to specific circumstances such as during shutdown that writes
> IER=0, there is nothing to stop the storm.
>
> During shutdown the storm is particularly problematic because
> serial8250_do_shutdown() calls synchronize_irq() that will hang in
> waiting for the storm to finish which never happens.
>
> This problem can also result in triggering a warning:
>
> irq 45: nobody cared (try booting with the "irqpoll" option)
> [...snip...]
> handlers:
> serial8250_interrupt
> Disabling IRQ #45
>
> Normal means to reset interrupt status by reading LSR, MSR, USR, or RX
> register do not result in the UART deasserting the IRQ.
>
> Add a quirk to INTC10EE UARTs to enable Tx interrupts if UART's Tx is
> currently empty and inactive. Rework IIR_NO_INT to keep track of the
> number of consecutive IIR_NO_INT, and on fourth one perform the quirk.
> Enabling Tx interrupts should change IIR value from IIR_NO_INT to
> IIR_THRI which has been observed to stop the storm.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
...
> +/*
> + * Number of consecutive IIR_NO_INT interrupts required to trigger interrupt
> + * storm prevention code.
> + */
> +#define DW_UART_QUIRK_IER_KICK_THRES 4
Actually if we...
> struct dw8250_platform_data {
> u8 usr_reg;
> unsigned int skip_autocfg:1;
> unsigned int uart_16550_compatible:1;
> +
> + u8 no_int_count;
...define this as
unsigned int no_int_count:2;
there will be no need to have a modulo at all. But I agree it might look a bit
weird.
> };
--
With Best Regards,
Andy Shevchenko
next prev parent reply other threads:[~2026-01-28 14:04 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-28 10:52 [PATCH v2 0/7] 8250 DW UART fixes when under constant Rx pressure Ilpo Järvinen
2026-01-28 10:52 ` [PATCH v2 1/7] serial: 8250: Protect LCR write in shutdown Ilpo Järvinen
2026-01-28 13:12 ` Andy Shevchenko
2026-01-28 10:52 ` [PATCH v2 2/7] serial: 8250_dw: Avoid unnecessary LCR writes Ilpo Järvinen
2026-01-28 13:36 ` Andy Shevchenko
2026-01-28 10:52 ` [PATCH v2 3/7] serial: 8250: Add serial8250_handle_irq_locked() Ilpo Järvinen
2026-01-28 13:20 ` Andy Shevchenko
2026-01-28 13:26 ` Ilpo Järvinen
2026-01-28 10:52 ` [PATCH v2 4/7] serial: 8250_dw: Rework dw8250_handle_irq() locking and IIR handling Ilpo Järvinen
2026-01-28 13:48 ` Andy Shevchenko
2026-01-28 14:00 ` Ilpo Järvinen
2026-01-28 10:52 ` [PATCH v2 5/7] serial: 8250_dw: Rework IIR_NO_INT handling to stop interrupt storm Ilpo Järvinen
2026-01-28 14:03 ` Andy Shevchenko [this message]
2026-01-28 10:53 ` [PATCH v2 6/7] serial: 8250: Add late synchronize_irq() to shutdown to handle DW UART BUSY Ilpo Järvinen
2026-01-28 14:37 ` Andy Shevchenko
2026-01-28 15:07 ` Ilpo Järvinen
2026-01-28 10:53 ` [PATCH v2 7/7] serial: 8250_dw: Ensure BUSY is deasserted Ilpo Järvinen
2026-01-28 15:42 ` Andy Shevchenko
2026-01-30 12:44 ` Ilpo Järvinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aXoXSxsem4hOLlrO@smile.fi.intel.com \
--to=andriy.shevchenko@linux.intel.com \
--cc=adriana@arista.com \
--cc=gregkh@linuxfoundation.org \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=qianfanguijin@163.com \
--cc=shankar.bandal@intel.com \
--cc=shanth.murthy@intel.com \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.