From: Frank Li <Frank.li@oss.nxp.com>
To: "Benoît Monin" <benoit.monin@bootlin.com>
Cc: Frank Li <Frank.Li@nxp.com>, Vinod Koul <vkoul@kernel.org>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Frank Li <Frank.Li@kernel.org>,
imx@lists.linux.dev, dmaengine@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v10 2/2] dmaengine: fsl-edma: Support dynamic scatter/gather chaining
Date: Fri, 11 Sep 2026 09:14:58 -0500 [thread overview]
Message-ID: <aqQM4rC18SoAA_KH@SMW015318> (raw)
In-Reply-To: <20260911-fsl-edma-dyn-sg-v10-2-700eb72def57@bootlin.com>
On Fri, Sep 11, 2026 at 03:11:37PM +0200, Benoît Monin wrote:
> Implement dynamic linking of scatter/gather transfers to enable
> chaining multiple DMA descriptors without stopping the channel.
> This avoids waiting for the channel to go idle if there is another
> transaction already issued.
>
> Add fsl_edma_link_sg() to dynamically link the last TCD of a previously
> issued descriptor to the first TCD of a new descriptor by setting the
> scatter/gather address and the E_SG flag, and keeping the channel active
> by clearing the DREQ bit.
>
> Also in fsl_edma_link_sg(), assign a non-zero identifier to the new
> descriptor that is stored in the EDMA_TCD_CSR_LINKCH field of the CSR
> of each TCD, after checking that the descriptors are not using channel
> linking. The use of this field (MAJORLINKCH in the datasheet) as an
> identifier for dynamic scatter/gather is suggested in the i.MX93 datasheet.
>
> When the last issued descriptor is the one currently active on the
> channel and has a single TCD, the scatter/gather address and CSR are
> also written directly to the hardware registers to ensure the link
> takes effect immediately, unless the DMA controller requires the DONE
> bit to be cleared for the CSR change to take effect. Clearing the DONE
> bit would disrupt the interrupt handler.
>
> Linking is done in fsl_edma_issue_pending(), which iterates over the
> submitted descriptors, links each one to the previously issued
> descriptor via fsl_edma_link_sg(), and then moves it to the issued
> list. This ensures that transactions are linked in the order they were
> issued. Linking of a descriptor is limited to 31 outstanding descriptors
> on the issued list so the identifier fits in the LINKCH field of the CSR
> register. The value of zero is left to identify non-linked descriptors.
>
> Update fsl_edma_xfer_desc() to avoid re-initializing the hardware when a
> transfer is already in progress, allowing seamless chaining of descriptors.
>
> Modify the transfer completion handler to check the DONE flag in the
> channel CSR before marking the transfer complete. Since this flag is only
> available on SoC with the split registers layout, only link transactions
> for DMA controllers flagged with newly added FSL_EDMA_DRV_CSR_LINKCH. This
> flag is set for eDMA3 and EDMA4 controllers which are able to perform
> dynamic scatter/gather linking.
>
> The completion handler also reaps issued descriptors whose link channel ID
> (EDMA_TCD_CSR_LINKCH) has already been passed by the hardware, marking
> them as completed even if their corresponding interrupt has been missed.
>
> Add trace event for scatter/gather linking operations.
>
> Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
> ---
Reviewed-by: Frank Li <Frank.Li@nxp.com>
> drivers/dma/fsl-edma-common.c | 138 ++++++++++++++++++++++++++++++++++++++++--
> drivers/dma/fsl-edma-common.h | 11 +++-
> drivers/dma/fsl-edma-trace.h | 5 ++
> 3 files changed, 146 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/dma/fsl-edma-common.c b/drivers/dma/fsl-edma-common.c
> index c5f5951c988b..76fbd2bc5154 100644
> --- a/drivers/dma/fsl-edma-common.c
> +++ b/drivers/dma/fsl-edma-common.c
> @@ -55,10 +55,36 @@ void fsl_edma_tx_chan_handler(struct fsl_edma_chan *fsl_chan)
> }
>
> if (!fsl_chan->edesc->iscyclic) {
> - list_del(&fsl_chan->edesc->vdesc.node);
> - vchan_cookie_complete(&fsl_chan->edesc->vdesc);
> + u16 csr = edma_read_tcdreg(fsl_chan, csr);
> + u8 link_sg_id = FIELD_GET(EDMA_TCD_CSR_LINKCH, csr);
> + struct virt_dma_desc *vdesc, *tmp;
> +
> + /* Channel is DONE when a TCD with D_REQ set completes */
> + if (!(fsl_edma_drvflags(fsl_chan) & FSL_EDMA_DRV_SPLIT_REG) ||
> + (edma_readl_chreg(fsl_chan, ch_csr) & EDMA_V3_CH_CSR_DONE)) {
> + fsl_chan->status = DMA_COMPLETE;
> + }
> +
> + list_for_each_entry_safe(vdesc, tmp, &fsl_chan->vchan.desc_issued, node) {
> + struct fsl_edma_desc *fsl_desc = to_fsl_edma_desc(vdesc);
> + bool id_match = (link_sg_id == fsl_desc->link_sg_id);
> +
> + /*
> + * If the transfer is still running,
> + * don't mark as complete the current descriptor
> + */
> + if (id_match && fsl_chan->status != DMA_COMPLETE)
> + break;
> +
> + list_del(&vdesc->node);
> + vchan_cookie_complete(vdesc);
> +
> + if (id_match)
> + break;
> + }
> +
> fsl_chan->edesc = NULL;
> - fsl_chan->status = DMA_COMPLETE;
> +
> } else {
> vchan_cyclic_callback(&fsl_chan->edesc->vdesc);
> }
> @@ -931,14 +957,99 @@ void fsl_edma_xfer_desc(struct fsl_edma_chan *fsl_chan)
> if (!vdesc)
> return;
> fsl_chan->edesc = to_fsl_edma_desc(vdesc);
> - fsl_edma_set_tcd_regs(fsl_chan, fsl_chan->edesc->tcd[0].vtcd);
> - fsl_edma_enable_request(fsl_chan);
> - fsl_chan->status = DMA_IN_PROGRESS;
> +
> + if (fsl_chan->status != DMA_IN_PROGRESS) {
> + fsl_edma_set_tcd_regs(fsl_chan, fsl_chan->edesc->tcd[0].vtcd);
> + fsl_edma_enable_request(fsl_chan);
> + fsl_chan->status = DMA_IN_PROGRESS;
> + }
> +}
> +
> +static void fsl_edma_link_sg(struct fsl_edma_chan *fsl_chan, struct fsl_edma_desc *fsl_desc)
> +{
> + u32 flags = fsl_edma_drvflags(fsl_chan);
> + struct fsl_edma_hw_tcd *last_tcd;
> + struct fsl_edma_desc *prev_desc;
> + struct virt_dma_desc *vdesc;
> + u16 last_csr;
> +
> + lockdep_assert_held(&fsl_chan->vchan.lock);
> +
> + if (!(flags & FSL_EDMA_DRV_CSR_LINKCH) || fsl_desc->iscyclic)
> + return;
> +
> + vdesc = list_last_entry_or_null(&fsl_chan->vchan.desc_issued,
> + struct virt_dma_desc, node);
> + if (!vdesc)
> + return;
> +
> + prev_desc = to_fsl_edma_desc(vdesc);
> + if (prev_desc->iscyclic)
> + return;
> +
> + last_tcd = prev_desc->tcd[prev_desc->n_tcds - 1].vtcd;
> + last_csr = fsl_edma_get_tcd_to_cpu(fsl_chan, last_tcd, csr);
> +
> + for (unsigned int i = 0; i < fsl_desc->n_tcds; i++) {
> + struct fsl_edma_hw_tcd *tcd = fsl_desc->tcd[i].vtcd;
> +
> + if (fsl_edma_get_tcd_to_cpu(fsl_chan, tcd, csr) & EDMA_TCD_CSR_E_LINK)
> + return;
> + }
> +
> + if (!(last_csr & EDMA_TCD_CSR_D_REQ) ||
> + last_csr & EDMA_TCD_CSR_E_LINK)
> + return;
> +
> + /* Set a non-zero linked SG identifier to all TCD of the new descriptor */
> + fsl_chan->link_sg_id++;
> + if (fsl_chan->link_sg_id > FIELD_MAX(EDMA_TCD_CSR_LINKCH))
> + fsl_chan->link_sg_id = 1;
> +
> + fsl_desc->link_sg_id = fsl_chan->link_sg_id;
> +
> + for (unsigned int i = 0; i < fsl_desc->n_tcds; i++) {
> + struct fsl_edma_hw_tcd *tcd = fsl_desc->tcd[i].vtcd;
> + u16 csr = fsl_edma_get_tcd_to_cpu(fsl_chan, tcd, csr);
> +
> + csr |= FIELD_PREP(EDMA_TCD_CSR_LINKCH, fsl_chan->link_sg_id);
> + fsl_edma_set_tcd_to_le(fsl_chan, tcd, csr, csr);
> + }
> +
> + /*
> + * Set DLAST_SGA before enabling E_SG in CSR: if the DMA engine
> + * only picks up the former, it updates DADDR at end of transfer,
> + * which is not reused.
> + */
> + fsl_edma_set_tcd_to_le(fsl_chan, last_tcd, fsl_desc->tcd[0].ptcd, dlast_sga);
> +
> + dma_wmb();
> +
> + last_csr &= ~EDMA_TCD_CSR_D_REQ;
> + last_csr |= EDMA_TCD_CSR_E_SG;
> + fsl_edma_set_tcd_to_le(fsl_chan, last_tcd, last_csr, csr);
> +
> + /*
> + * Update the registers if the engine already loaded the TCD,
> + * unless doing so requires clearing the DONE bit, as that could
> + * lead to lost completion.
> + */
> + if (prev_desc == fsl_chan->edesc &&
> + prev_desc->n_tcds == 1 &&
> + !(flags & FSL_EDMA_DRV_CLEAR_DONE_E_SG)) {
> + edma_cp_tcd_to_reg(fsl_chan, last_tcd, dlast_sga);
> + edma_cp_tcd_to_reg(fsl_chan, last_tcd, csr);
> + }
> +
> + trace_edma_link_sg(fsl_chan, last_tcd);
> }
>
> void fsl_edma_issue_pending(struct dma_chan *chan)
> {
> struct fsl_edma_chan *fsl_chan = to_fsl_edma_chan(chan);
> + struct virt_dma_desc *vdesc, *tmp;
> + size_t issued_count = 0;
> + struct list_head *pos;
> unsigned long flags;
>
> spin_lock_irqsave(&fsl_chan->vchan.lock, flags);
> @@ -949,6 +1060,21 @@ void fsl_edma_issue_pending(struct dma_chan *chan)
> return;
> }
>
> + /* Count the issued desc up to the maximum number of linked SG id */
> + list_for_each(pos, &fsl_chan->vchan.desc_issued) {
> + if (++issued_count > FIELD_MAX(EDMA_TCD_CSR_LINKCH))
> + break;
> + }
> +
> + /* Link the SG descriptors with the available identifiers */
> + list_for_each_entry_safe(vdesc, tmp, &fsl_chan->vchan.desc_submitted, node) {
> + if (++issued_count > FIELD_MAX(EDMA_TCD_CSR_LINKCH))
> + break;
> + fsl_edma_link_sg(fsl_chan, to_fsl_edma_desc(vdesc));
> + list_move_tail(&vdesc->node, &fsl_chan->vchan.desc_issued);
> + }
> +
> + /* Issue the rest of the descriptors unlinked */
> if (vchan_issue_pending(&fsl_chan->vchan) && !fsl_chan->edesc)
> fsl_edma_xfer_desc(fsl_chan);
>
> diff --git a/drivers/dma/fsl-edma-common.h b/drivers/dma/fsl-edma-common.h
> index 0d028048701d..cbb077e98f55 100644
> --- a/drivers/dma/fsl-edma-common.h
> +++ b/drivers/dma/fsl-edma-common.h
> @@ -42,6 +42,7 @@
> #define EDMA_TCD_CSR_E_LINK BIT(5)
> #define EDMA_TCD_CSR_ACTIVE BIT(6)
> #define EDMA_TCD_CSR_DONE BIT(7)
> +#define EDMA_TCD_CSR_LINKCH GENMASK(12, 8)
>
> #define EDMA_V3_TCD_NBYTES_MLOFF_NBYTES(x) ((x) & GENMASK(9, 0))
> #define EDMA_V3_TCD_NBYTES_MLOFF(x) (x << 10)
> @@ -169,6 +170,7 @@ struct fsl_edma_chan {
> struct dma_slave_config cfg;
> u32 attr;
> bool is_sw;
> + u8 link_sg_id;
> struct dma_pool *tcd_pool;
> dma_addr_t dma_dev_addr;
> u32 dma_dev_size;
> @@ -199,6 +201,7 @@ struct fsl_edma_desc {
> struct virt_dma_desc vdesc;
> struct fsl_edma_chan *echan;
> bool iscyclic;
> + u8 link_sg_id;
> enum dma_transfer_direction dirn;
> unsigned int n_tcds;
> struct fsl_edma_sw_tcd tcd[];
> @@ -225,6 +228,8 @@ struct fsl_edma_desc {
> #define FSL_EDMA_DRV_TCD64 BIT(15)
> /* All channel ERR IRQ share one IRQ line */
> #define FSL_EDMA_DRV_ERRIRQ_SHARE BIT(16)
> +/* Major link channel in CSR used for linking SG descriptors */
> +#define FSL_EDMA_DRV_CSR_LINKCH BIT(17)
>
>
> #define FSL_EDMA_DRV_EDMA3 (FSL_EDMA_DRV_SPLIT_REG | \
> @@ -232,13 +237,15 @@ struct fsl_edma_desc {
> FSL_EDMA_DRV_DEV_TO_DEV | \
> FSL_EDMA_DRV_ALIGN_64BYTE | \
> FSL_EDMA_DRV_CLEAR_DONE_E_SG | \
> - FSL_EDMA_DRV_CLEAR_DONE_E_LINK)
> + FSL_EDMA_DRV_CLEAR_DONE_E_LINK | \
> + FSL_EDMA_DRV_CSR_LINKCH)
>
> #define FSL_EDMA_DRV_EDMA4 (FSL_EDMA_DRV_SPLIT_REG | \
> FSL_EDMA_DRV_BUS_8BYTE | \
> FSL_EDMA_DRV_DEV_TO_DEV | \
> FSL_EDMA_DRV_ALIGN_64BYTE | \
> - FSL_EDMA_DRV_CLEAR_DONE_E_LINK)
> + FSL_EDMA_DRV_CLEAR_DONE_E_LINK | \
> + FSL_EDMA_DRV_CSR_LINKCH)
>
> struct fsl_edma_drvdata {
> u32 dmamuxs; /* only used before v3 */
> diff --git a/drivers/dma/fsl-edma-trace.h b/drivers/dma/fsl-edma-trace.h
> index 45d964a3726d..f4b0021d2bd0 100644
> --- a/drivers/dma/fsl-edma-trace.h
> +++ b/drivers/dma/fsl-edma-trace.h
> @@ -121,6 +121,11 @@ DEFINE_EVENT(edma_log_tcd, edma_fill_tcd,
> TP_ARGS(chan, tcd)
> );
>
> +DEFINE_EVENT(edma_log_tcd, edma_link_sg,
> + TP_PROTO(struct fsl_edma_chan *chan, void *tcd),
> + TP_ARGS(chan, tcd)
> +);
> +
> #endif
>
> /* this part must be outside header guard */
>
> --
> 2.55.0
>
next prev parent reply other threads:[~2026-09-11 14:15 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-11 13:11 [PATCH v10 0/2] dmaengine: fsl-edma: Scatter/gather improvements Benoît Monin
2026-09-11 13:11 ` [PATCH v10 1/2] dmaengine: fsl-edma: Implement device_prep_peripheral_dma_vec Benoît Monin
2026-09-11 13:27 ` sashiko-bot
2026-09-11 13:11 ` [PATCH v10 2/2] dmaengine: fsl-edma: Support dynamic scatter/gather chaining Benoît Monin
2026-09-11 13:23 ` sashiko-bot
2026-09-11 14:14 ` Frank Li [this message]
2026-09-15 17:31 ` [PATCH v10 0/2] dmaengine: fsl-edma: Scatter/gather improvements Vinod Koul
2026-10-05 15:42 ` Vinod Koul
-- strict thread matches above, loose matches on Subject: below --
2026-09-23 13:16 [PATCH v10 2/2] dmaengine: fsl-edma: Support dynamic scatter/gather chaining kernel test robot
2026-09-24 3:39 kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aqQM4rC18SoAA_KH@SMW015318 \
--to=frank.li@oss.nxp.com \
--cc=Frank.Li@kernel.org \
--cc=Frank.Li@nxp.com \
--cc=benoit.monin@bootlin.com \
--cc=dmaengine@vger.kernel.org \
--cc=imx@lists.linux.dev \
--cc=linux-kernel@vger.kernel.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.