All of lore.kernel.org
 help / color / mirror / Atom feed
From: Frank Li <Frank.li@oss.nxp.com>
To: Haoning Cheng <Haoning.CHENG@cn.bosch.com>
Cc: Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Shawn Guo <shawnguo@kernel.org>, Frank Li <Frank.Li@nxp.com>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	imx@lists.linux.dev, linux-arm-kernel@lists.infradead.org,
	Leonhard Hesse <leonhard.hesse@bshg.com>
Subject: Re: [PATCH v2 3/8] ARM: dts: imx6ulz: Adjust BSH SMM-M2 Wi-Fi and Bluetooth pin settings
Date: Fri, 6 Nov 2026 10:47:25 -0600	[thread overview]
Message-ID: <au4EnWiIRT4xoT-6@SMW015318> (raw)
In-Reply-To: <20261105-add-bsh-smm-m2-v2-3-fb5ffc7da486@cn.bosch.com>

On Thu, Nov 05, 2026 at 10:41:17AM +0800, Haoning Cheng wrote:
> From: Leonhard Hesse <leonhard.hesse@bshg.com>
>
> Adjustment of wifi and bluetooth REG_ON pin settings.
> Tests have shown that minor changes in drive strength, slew rate
> and speed resulted in the best performance.

It is just GPIO, why strength, slew rate impact performace?

Frank

>
> Signed-off-by: Leonhard Hesse <leonhard.hesse@bshg.com>
> Signed-off-by: Haoning Cheng <Haoning.CHENG@cn.bosch.com>
> ---
>  arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> index aac211a9f9eb..dabe17222f13 100644
> --- a/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> +++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> @@ -125,7 +125,7 @@ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
>  			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b099
>  			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
>  			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b099
> -			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x79		/* BT_REG_ON */
> +			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x100b1		/* BT_REG_ON */
>  			MX6UL_PAD_SD1_CLK__GPIO2_IO17		0x100b1		/* BT_DEV_WAKE out */
>  			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b0b0		/* BT_HOST_WAKE in */
>  		>;
> @@ -146,7 +146,7 @@ MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17059
>  			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17059
>  			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17059
>  			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17059
> -			MX6UL_PAD_SD1_DATA3__GPIO2_IO21		0x79		/* WL_REG_ON */
> +			MX6UL_PAD_SD1_DATA3__GPIO2_IO21		0x3029		/* WL_REG_ON */
>  			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22	0x100b1		/* WL_DEV_WAKE - WiFi_GPIO_4 - WiFi FW UART */
>  			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x1b0b1		/* WL_HOST_WAKE - WIFI_GPIO_0 - OOB IRQ */
>  			MX6UL_PAD_ENET1_RX_EN__OSC32K_32K_OUT	0x4001b031	/* OSC 32Khz wifi clk in */
>
> --
> 2.43.0
>
>

  reply	other threads:[~2026-11-06 16:47 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-05  2:41 [PATCH v2 0/8] Update BSH SystemMaster device trees and add SMM-M2B support Haoning Cheng
2026-11-05  2:41 ` [PATCH v2 1/8] dt-bindings: arm: fsl: Add BSH SMM-M2B board Haoning Cheng
2026-11-06 12:51   ` Krzysztof Kozlowski
2026-11-05  2:41 ` [PATCH v2 2/8] dts: imx: Use minimum NAND ECC strength on BSH boards Haoning Cheng
2026-11-05  2:48   ` sashiko-bot
2026-11-05  3:23     ` Haoning Cheng
2026-11-05  2:41 ` [PATCH v2 3/8] ARM: dts: imx6ulz: Adjust BSH SMM-M2 Wi-Fi and Bluetooth pin settings Haoning Cheng
2026-11-06 16:47   ` Frank Li [this message]
2026-11-05  2:41 ` [PATCH v2 4/8] ARM: dts: imx6ulz: Fix BSH SMM-M2 WLAN host wake configuration Haoning Cheng
2026-11-06 16:50   ` Frank Li
2026-11-05  2:41 ` [PATCH v2 5/8] ARM: dts: imx6ulz: Factor out BSH SMM-M2 common device tree Haoning Cheng
2026-11-05  2:41 ` [PATCH v2 6/8] ARM: dts: imx6ulz: Add BSH SMM-M2B board support Haoning Cheng
2026-11-05  2:41 ` [PATCH v2 7/8] ARM: dts: imx6ulz: Configure UART2 pins on BSH SMM-M2 variants Haoning Cheng
2026-11-05  2:41 ` [PATCH v2 8/8] dts: imx: Enable USB OTG mode on BSH SMM-M2 and SMM-S2 Haoning Cheng
2026-11-06 16:44   ` Frank Li

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=au4EnWiIRT4xoT-6@SMW015318 \
    --to=frank.li@oss.nxp.com \
    --cc=Frank.Li@nxp.com \
    --cc=Haoning.CHENG@cn.bosch.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=imx@lists.linux.dev \
    --cc=kernel@pengutronix.de \
    --cc=krzk+dt@kernel.org \
    --cc=leonhard.hesse@bshg.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.