Re: [PATCH net-next 2/2] net: phy: marvell: add RGMII-to-Copper mode configuration

["Marek Behún" <kabel@kernel.org>]

On Mon, Nov 09, 2026 at 01:44:56PM +0100, Paul Louvel wrote:
> The driver currently programs it only for SGMII-to-Copper, based on the
> PHY interface mode.
> 
> Some MAC connect to the PHY via RGMII. Add code to configure the device
> in m88e1510_config_init().
> 
> Signed-off-by: Paul Louvel (Schneider Electric) <paul.louvel@bootlin.com>
> ---
>  drivers/net/phy/marvell.c | 31 +++++++------------------------
>  1 file changed, 7 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
> index aef5f8279133..b8b466eb1c45 100644
> --- a/drivers/net/phy/marvell.c
> +++ b/drivers/net/phy/marvell.c
> @@ -1394,31 +1394,14 @@ static int m88e1510_config_init(struct phy_device *phydev)
>  	if (err < 0)
>  		return err;
>  
> -	/* SGMII-to-Copper mode initialization */
> -	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
> -		/* Select page 18 */
> -		err = marvell_set_page(phydev, 18);
> -		if (err < 0)
> -			return err;
> -
> -		/* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */
> -		err = phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1,
> -				 MII_88E1510_GEN_CTRL_REG_1_MODE_MASK,
> -				 MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII);
> -		if (err < 0)
> -			return err;
> -
> -		/* PHY reset is necessary after changing MODE[2:0] */
> -		err = phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1,
> -				   MII_88E1510_GEN_CTRL_REG_1_RESET);
> -		if (err < 0)
> -			return err;
> +	/* RGMII/SGMII-to-Copper mode initialization */
> +	if (phydev->interface == PHY_INTERFACE_MODE_SGMII)
> +		err = m88e1510_config_mode(phydev, MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII);

This first part belongs either to the first patch (deduplicates the mode setting code)
or to a separate patch.

Marek

> +	else if (phy_interface_is_rgmii(phydev))
> +		err = m88e1510_config_mode(phydev, MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII);
> +	if (err < 0)
> +		return err;
>  
> -		/* Reset page selection */
> -		err = marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE);
> -		if (err < 0)
> -			return err;
> -	}
>  	err = m88e1011_set_downshift(phydev, 3);
>  	if (err < 0)
>  		return err;
> 
> -- 
> 2.56.0
> 
>