All of lore.kernel.org
 help / color / mirror / Atom feed
From: Yao Zi <me@ziyao.cc>
To: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>,
	Yao Zi <me@ziyao.cc>
Cc: u-boot@lists.u-boot-project.org,
	Tim Ouyang <tim609@andestech.com>,
	Leo Liang <leo.liang@sifive.com>, Tom Rini <trini@konsulko.com>,
	E Shattow <e@freeshell.de>,
	Troy Mitchell <troy.mitchell@linux.spacemit.com>
Subject: Re: [PATCH v3] riscv: Disable M-IMSIC and M-APLIC nodes in DT passed to next stage in S mode
Date: Fri, 20 Nov 2026 17:07:10 +0000	[thread overview]
Message-ID: <awB-PvfuEDIu_t0l@pie> (raw)
In-Reply-To: <CAEev2e9SdqXvipxXGXFjLqe77RA=LsbGSY8AFnL9VbbYAC0ZJQ@mail.gmail.com>

On Fri, Nov 20, 2026 at 10:09:49AM -0600, Anirudh Srinivasan wrote:
> Hi Yao,
> 
> On Fri, Nov 20, 2026 at 4:47 AM Yao Zi <me@ziyao.cc> wrote:
> >
> > On Thu, Nov 19, 2026 at 09:47:07AM -0600, Anirudh Srinivasan wrote:
> > > When U-Boot is running in S mode, the DT passed to the next S mode stage
> > > can either be the bundled in DT U-Boot and the previous M mode stage
> > > use, or be loaded by U-Boot from some boot media. In the former case,
> > > the M mode stage can fix up the DT to disable the M-IMSIC and M-APLIC
> > > nodes on an AIA system (for example, OpenSBI does this fixup). These
> > > controllers are to be managed by M-mode software, so this is done to
> > > prevent S mode software from trying to probe them.
> > >
> > > This fixup doesn't happen in the latter case because U-Boot loads a
> > > fresh DT from boot media. Add a fdt fixup to do this similar to OpenSBI.
> > > This gets rid of prints like this during linux boots.
> > >
> > > [    0.000000] riscv-imsic: interrupt-controller@a0000000: no parent irqs available
> > > [    0.000000] riscv-imsic: interrupt-controller@a0000000: failed to setup state (error -22)
> > > [    0.000000] OF: of_irq_init: Failed to init /soc/interrupt-controller@a0000000 ((____ptrval____)), parent (____ptrval____)
> > >
> > > [   10.727605] platform cc000000.interrupt-controller: deferred probe pending: platform: supplier a0000000.interrupt-controller not ready
> > >
> > > Reviewed-by: E Shattow <e@freeshell.de>
> > > Signed-off-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
> > > ---
> > > Changes in v3:
> > > - Reword commit title to say M-APLIC/M-IMSIC and drop references to M Mode to avoid any confusion
> > > - Link to v2: https://patch.msgid.link/20261119-mimsic_maplic_fixup-v2-1-e29e04bf1b76@oss.tenstorrent.com
> > >
> > > Changes in v2:
> > > - Rename riscv_aia_mmode_aplic_imsic_fixup to riscv_aia_mimsic_maplic_fixup
> > > - Drop most references to OpenSBI/Linux in commit message and just use M-mode/s-mode software
> > > - Link to v1: https://patch.msgid.link/20261118-mimsic_maplic_fixup-v1-1-52dea8f39779@oss.tenstorrent.com
> > > ---
> > >  arch/riscv/lib/fdt_fixup.c | 86 ++++++++++++++++++++++++++++++++++++++++++++++
> > >  1 file changed, 86 insertions(+)

...

> > > + * riscv_aia_mimsic_maplic_fixup() - Disable M-APLIC and M-IMSIC nodes in DT
> > > + * @fdt: Pointer to the device tree in which nodes are to be disabled
> > > + *
> > > + * On RISC-V AIA systems, M-mode software manages the M-APLIC and M-IMSIC.
> > > + * If S-mode U-Boot loads a device tree from boot media, the DT nodes for these
> > > + * could still be enabled, so fixup the DT to disable these nodes before passing
> > > + * it to the next S-mode stage.
> > > + *
> > > + * Return: 0 on success or error otherwise.
> > > + */
> > > +static int riscv_aia_mimsic_maplic_fixup(void *fdt)
> > > +{
> > > +     int offset, err;
> > > +
> > > +     /* Disable M-IMSIC in APLIC-IMSIC configuration */
> > > +     fdt_for_each_node_by_compatible(offset, fdt, -1, "riscv,imsics") {
> > > +             if (riscv_node_handles_mmode_external_interrupts(fdt, offset)) {
> > > +                     err = fdt_status_disabled(fdt, offset);
> >
> > Should we use "reserved" instead of "disabled"? Quoting the devicetree
> > specification,
> >
> > > "disabled"
> > >       Indicates that the device is not presently operational, but it
> > >       might become operational in the future (for example, something
> > >       is not plugged in, or switched off).
> > >
> > > "reserved"
> > >       Indicates that the device is operational, but should not be
> > >       used. Typically this is used for devices that are controlled by
> > >       another software component, such as platform firmware.
> >
> > Another possible problem is that these loops overrides the status
> > unconditionally, turning already "reserved" devices into "disabled".
> 
> I don't think we should be using reserved here. OpenSBI sets the node
> to disabled, so we should be doing the same thing.
> 
> I'll add a check to see if the node is enabled and disable it only then.

I think this is probably an OpenSBI defect, please try raising this to
OpenSBI upstream.

[...]

> Thanks for your comments. I'll address the style issues.
> 
> >
> > --
> > Thanks,
> > Yao Zi
> >
> > Meow-mrrp-mrow, I'm a cat.

-- 
Thanks,
Yao Zi

Meow-mrrp-mrow, I'm a cat.

  reply	other threads:[~2026-11-20 17:07 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-19 15:47 [PATCH v3] riscv: Disable M-IMSIC and M-APLIC nodes in DT passed to next stage in S mode Anirudh Srinivasan
2026-11-19 21:31 ` E Shattow
2026-11-20  1:04   ` Anirudh Srinivasan
2026-11-20 10:46 ` Yao Zi
2026-11-20 16:09   ` Anirudh Srinivasan
2026-11-20 17:07     ` Yao Zi [this message]
2026-11-20 17:24       ` Anirudh Srinivasan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=awB-PvfuEDIu_t0l@pie \
    --to=me@ziyao.cc \
    --cc=asrinivasan@oss.tenstorrent.com \
    --cc=e@freeshell.de \
    --cc=leo.liang@sifive.com \
    --cc=tim609@andestech.com \
    --cc=trini@konsulko.com \
    --cc=troy.mitchell@linux.spacemit.com \
    --cc=u-boot@lists.u-boot-project.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.