From: adam radford <aradford@gmail.com>
To: Kyle Moffett <mrmacman_g4@mac.com>
Cc: LKML kernel <linux-kernel@vger.kernel.org>
Subject: Re: SCSI opcode 0x80 and 3ware Escalade 7000 ATA RAID
Date: Fri, 15 Apr 2005 15:50:56 -0700 [thread overview]
Message-ID: <b1bc6a0005041515505419ba1e@mail.gmail.com> (raw)
In-Reply-To: <8c5d8e66ebfcfe879244a18068544dc3@mac.com>
Make sure you are are using the 3ware character ioctl interface
at /dev/twe0 (dynamic major, controller number minor) for your smartmontools,
not /dev/sda.
i.e. smartctl -a -d 3ware,X /dev/tweY
where X = port # of the drive whose information you want, Y=controller #.
The old interface from smartmontools used SCSI_IOCTL_SEND_COMMAND ioctls
with a special passthru opcode of 0x80 that would get passed to the
driver. This interface
is deprecated in the driver and the kernel.
-Adam
On 4/15/05, Kyle Moffett <mrmacman_g4@mac.com> wrote:
> I've been getting the following message in syslog on a couple of my
> servers
> recently:
>
> > Apr 15 16:41:18 king kernel: scsi: unknown opcode 0x80
>
> I've tracked it down to the SCSI opcode verification patch that went in
> a
> while back. I also determined that the trigger was our smartd/smartctl
> runs,
> which execute tests and get status on a regular basis. Our kernel is
> latest
> Debian kernel-image-2.6.8-686-smp, although I've verified identical
> behavior
> with a recent kernel.org kernel.
>
> The below strace run generates exactly 8 warnings every time.
>
> On another (unrelated) note, we also get the following messages at the
> rate
> at which our Cisco does IPv6 router-announcement broadcasts. This is on
> every kernel that we have, from 2.4 through 2.6. Is there something
> wrong
> with our setup, or is this just a spurious error? (NOTE: I don't know
> for
> sure that our Cisco's set up properly, we're all new at IPv6 here, and
> we're
> not actually relying on the advertising yet, so...)
>
> > Apr 15 18:01:27 king kernel: IPv6 addrconf: prefix with wrong length 49
>
> I'll get a packet trace of necessary.
>
> Thanks for your help!
>
> Here's an example smartctl log (Without the console warnings).
> > # strace -o smart.trace smartctl /dev/sda -d 3ware,0 -a
> > smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
> > Home page is http://smartmontools.sourceforge.net/
> >
> > === START OF INFORMATION SECTION ===
> > Device Model: Maxtor 6Y200P0
> > Serial Number: Y60PVCZE
> > Firmware Version: YAR41BW0
> > Device is: In smartctl database [for details use: -P show]
> > ATA Version is: 7
> > ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
> > Local Time is: Fri Apr 15 17:25:49 2005 EDT
> > SMART support is: Available - device has SMART capability.
> > SMART support is: Enabled
> >
> > === START OF READ SMART DATA SECTION ===
> > SMART overall-health self-assessment test result: PASSED
> >
> > General SMART Values:
> > Offline data collection status: (0x82) Offline data collection
> > activity
> > was completed without error.
> > Auto Offline Data Collection:
> > Enabled.
> > Self-test execution status: ( 0) The previous self-test routine
> > completed
> > without error or no self-test
> > has ever
> > been run.
> > Total time to complete Offline
> > data collection: ( 243) seconds.
> > Offline data collection
> > capabilities: (0x5b) SMART execute Offline
> > immediate.
> > Auto Offline data collection
> > on/off support.
> > Suspend Offline collection
> > upon new
> > command.
> > Offline surface scan supported.
> > Self-test supported.
> > No Conveyance Self-test
> > supported.
> > Selective Self-test supported.
> > SMART capabilities: (0x0003) Saves SMART data before
> > entering
> > power-saving mode.
> > Supports SMART auto save timer.
> > Error logging capability: (0x01) Error logging supported.
> > No General Purpose Logging
> > support.
> > Short self-test routine
> > recommended polling time: ( 2) minutes.
> > Extended self-test routine
> > recommended polling time: ( 91) minutes.
> >
> > SMART Attributes Data Structure revision number: 16
> > Vendor Specific SMART Attributes with Thresholds:
> > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
> > UPDATED WHEN_FAILED RAW_VALUE
> > 3 Spin_Up_Time 0x0027 252 252 063 Pre-fail
> > Always - 5945
> > 4 Start_Stop_Count 0x0032 253 253 000 Old_age
> > Always - 17
> > 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail
> > Always - 1
> > 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
> > Offline - 0
> > 7 Seek_Error_Rate 0x000a 253 252 000 Old_age
> > Always - 0
> > 8 Seek_Time_Performance 0x0027 251 248 187 Pre-fail
> > Always - 47575
> > 9 Power_On_Minutes 0x0032 220 220 000 Old_age
> > Always - 849h+05m
> > 10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail
> > Always - 0
> > 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
> > Always - 0
> > 12 Power_Cycle_Count 0x0032 253 253 000 Old_age
> > Always - 19
> > 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age
> > Always - 0
> > 193 Load_Cycle_Count 0x0032 253 253 000 Old_age
> > Always - 0
> > 194 Temperature_Celsius 0x0032 253 253 000 Old_age
> > Always - 12
> > 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age
> > Always - 5743
> > 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age
> > Offline - 0
> > 197 Current_Pending_Sector 0x0008 253 253 000 Old_age
> > Offline - 0
> > 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age
> > Offline - 0
> > 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age
> > Offline - 0
> > 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age
> > Always - 0
> > 201 Soft_Read_Error_Rate 0x000a 253 251 000 Old_age
> > Always - 5
> > 202 TA_Increase_Count 0x000a 253 252 000 Old_age
> > Always - 0
> > 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail
> > Always - 0
> > 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age
> > Always - 0
> > 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age
> > Always - 0
> > 207 Spin_High_Current 0x002a 252 252 000 Old_age
> > Always - 0
> > 208 Spin_Buzz 0x002a 252 252 000 Old_age
> > Always - 0
> > 209 Offline_Seek_Performnce 0x0024 196 191 000 Old_age
> > Offline - 0
> > 99 Unknown_Attribute 0x0004 253 253 000 Old_age
> > Offline - 0
> > 100 Unknown_Attribute 0x0004 253 253 000 Old_age
> > Offline - 0
> > 101 Unknown_Attribute 0x0004 253 253 000 Old_age
> > Offline - 0
> >
> > SMART Error Log Version: 1
> > ATA Error Count: 1
> > CR = Command Register [HEX]
> > FR = Features Register [HEX]
> > SC = Sector Count Register [HEX]
> > SN = Sector Number Register [HEX]
> > CL = Cylinder Low Register [HEX]
> > CH = Cylinder High Register [HEX]
> > DH = Device/Head Register [HEX]
> > DC = Device Command Register [HEX]
> > ER = Error register [HEX]
> > ST = Status register [HEX]
> > Powered_Up_Time is measured from power on, and printed as
> > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
> > SS=sec, and sss=millisec. It "wraps" after 49.710 days.
> >
> > Error 1 occurred at disk power-on lifetime: 4990 hours (207 days + 22
> > hours)
> > When the command that caused the error occurred, the device was in
> > an unknown state.
> >
> > After command completion occurred, registers were:
> > ER ST SC SN CL CH DH
> > -- -- -- -- -- -- --
> > 40 51 03 bb bc 0c e0 Error: UNC 3 sectors at LBA = 0x000cbcbb =
> > 834747
> >
> > Commands leading to the command that caused the error were:
> > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> > -- -- -- -- -- -- -- -- ---------------- --------------------
> > 25 00 08 bb bc 0c e0 00 23d+08:28:01.392 READ DMA EXT
> > 25 00 10 83 bc 0c e0 00 23d+08:28:01.392 READ DMA EXT
> > 25 00 08 3b bc 0c e0 00 23d+08:28:01.392 READ DMA EXT
> > 25 00 08 33 bc 0c e0 00 23d+08:28:01.392 READ DMA EXT
> > 25 00 08 13 bc 0c e0 00 23d+08:28:01.392 READ DMA EXT
> >
> > SMART Self-test log structure revision number 1
> > Num Test_Description Status Remaining
> > LifeTime(hours) LBA_of_first_error
> > # 1 Short offline Completed without error 00% 11020
> > -
> > # 2 Short offline Completed without error 00% 10997
> > -
> > # 3 Short offline Completed without error 00% 10975
> > -
> > # 4 Short offline Completed without error 00% 10953
> > -
> > # 5 Short offline Completed without error 00% 10930
> > -
> > # 6 Extended offline Completed without error 00% 10909
> > -
> > # 7 Short offline Completed without error 00% 10885
> > -
> > # 8 Short offline Completed without error 00% 10863
> > -
> > # 9 Short offline Completed without error 00% 10841
> > -
> > #10 Short offline Completed without error 00% 10818
> > -
> > #11 Short offline Completed without error 00% 10796
> > -
> > #12 Short offline Completed without error 00% 10774
> > -
> > #13 Extended offline Completed without error 00% 10754
> > -
> > #14 Short offline Completed without error 00% 10730
> > -
> > #15 Short offline Completed without error 00% 10707
> > -
> > #16 Short offline Completed without error 00% 10685
> > -
> > #17 Short offline Completed without error 00% 10663
> > -
> > #18 Short offline Completed without error 00% 10640
> > -
> > #19 Short offline Completed without error 00% 10618
> > -
> > #20 Extended offline Completed without error 00% 10597
> > -
> > #21 Short offline Completed without error 00% 10573
> > -
> >
> > SMART Selective self-test log data structure revision number 1
> > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> > 1 0 0 Not_testing
> > 2 0 0 Not_testing
> > 3 0 0 Not_testing
> > 4 0 0 Not_testing
> > 5 0 0 Not_testing
> > Selective self-test flags (0x0):
> > After scanning selected spans, do NOT read-scan remainder of disk.
> > If Selective self-test is pending on power-up, resume after 0 minute
> > delay.
>
> > # cat smartctl.trace
> > execve("/usr/sbin/smartctl", ["smartctl", "/dev/sda", "-d", "3ware,0",
> > "-a"], [/* 19 vars */]) = 0
> > uname({sys="Linux", node="king", ...}) = 0
> > brk(0) = 0x807d000
> > old_mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS,
> > -1, 0) = 0x40017000
> > access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or
> > directory)
> > open("/etc/ld.so.preload", O_RDONLY) = -1 ENOENT (No such file or
> > directory)
> > open("/etc/ld.so.cache", O_RDONLY) = 3
> > fstat64(3, {st_mode=S_IFREG|0644, st_size=23579, ...}) = 0
> > old_mmap(NULL, 23579, PROT_READ, MAP_PRIVATE, 3, 0) = 0x40018000
> > close(3) = 0
> > access("/etc/ld.so.nohwcap", F_OK) = -1 ENOENT (No such file or
> > directory)
> > open("/lib/tls/libc.so.6", O_RDONLY) = 3
> > read(3, "\177ELF\1\1\1\0\0\0\0\0\0\0\0\0\3\0\3\0\1\0\0\0\360Y\1"...,
> > 512) = 512
> > fstat64(3, {st_mode=S_IFREG|0644, st_size=1253924, ...}) = 0
> > old_mmap(NULL, 1260140, PROT_READ|PROT_EXEC, MAP_PRIVATE, 3, 0) =
> > 0x4001e000
> > old_mmap(0x40147000, 32768, PROT_READ|PROT_WRITE,
> > MAP_PRIVATE|MAP_FIXED, 3, 0x129000) = 0x40147000
> > old_mmap(0x4014f000, 10860, PROT_READ|PROT_WRITE,
> > MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x4014f000
> > close(3) = 0
> > old_mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS,
> > -1, 0) = 0x40152000
> > set_thread_area({entry_number:-1 -> 6, base_addr:0x401522a0,
> > limit:1048575, seg_32bit:1, contents:0, read_exec_only:0,
> > limit_in_pages:1, seg_not_present:0, useable:1}) = 0
> > munmap(0x40018000, 23579) = 0
> > brk(0) = 0x807d000
> > brk(0x809e000) = 0x809e000
> > brk(0) = 0x809e000
> > fstat64(1, {st_mode=S_IFREG|0644, st_size=0, ...}) = 0
> > mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1,
> > 0) = 0x40018000
> > write(1, "smartctl version 5.32 Copyright "..., 55) = 55
> > write(1, "Home page is http://smartmontool"..., 52) = 52
> > open("/dev/sda", O_RDONLY|O_NONBLOCK) = 3
> > ioctl(3, FIBMAP, 0xbfffe290) = 0
> > write(1, "=== START OF INFORMATION SECTION"..., 37) = 37
> > write(1, "Device Model: ", 18) = 18
> > write(1, "Maxtor 6Y200P0\n", 15) = 15
> > write(1, "Serial Number: ", 18) = 18
> > write(1, "Y60PVCZE\n", 9) = 9
> > write(1, "Firmware Version: ", 18) = 18
> > write(1, "YAR41BW0\n", 9) = 9
> > write(1, "Device is: In smartctl da"..., 66) = 66
> > write(1, "ATA Version is: 7\n", 20) = 20
> > write(1, "ATA Standard is: ATA/ATAPI-7 T1"..., 51) = 51
> > time(NULL) = 1113600349
> > open("/usr/share/zoneinfo/GMT", O_RDONLY) = 4
> > fstat64(4, {st_mode=S_IFREG|0644, st_size=56, ...}) = 0
> > mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1,
> > 0) = 0x40019000
> > read(4, "TZif\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\1\0\0\0\1\0"...,
> > 4096) = 56
> > close(4) = 0
> > munmap(0x40019000, 4096) = 0
> > open("/etc/localtime", O_RDONLY) = 4
> > fstat64(4, {st_mode=S_IFREG|0644, st_size=1267, ...}) = 0
> > mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1,
> > 0) = 0x40019000
> > read(4, "TZif\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0"...,
> > 4096) = 1267
> > close(4) = 0
> > munmap(0x40019000, 4096) = 0
> > write(1, "Local Time is: Fri Apr 15 17:"..., 47) = 47
> > write(1, "SMART support is: Available - de"..., 59) = 59
> > write(1, "SMART support is: Enabled\n", 26) = 26
> > write(1, "\n", 1) = 1
> > ioctl(3, FIBMAP, 0xbfffe2a0) = 0
> > ioctl(3, FIBMAP, 0xbfffe2a0) = 0
> > ioctl(3, FIBMAP, 0xbfffe2a0) = 0
> > ioctl(3, FIBMAP, 0xbfffe2a0) = 0
> > write(1, "=== START OF READ SMART DATA SEC"..., 41) = 41
> > write(1, "SMART overall-health self-assess"..., 57) = 57
> > write(1, "\n", 1) = 1
> > write(1, "General SMART Values:\n", 22) = 22
> > write(1, "Offline data collection status: "..., 40) = 40
> > write(1, "Offline data collection activity"..., 67) = 67
> > write(1, "\t\t\t\t\tAuto Offline Data Collectio"..., 44) = 44
> > write(1, "Self-test execution status: "..., 33) = 33
> > write(1, "( 0)\tThe previous self-test ro"..., 53) = 53
> > write(1, "without error or no self-test ha"..., 55) = 55
> > write(1, "Total time to complete Offline \n", 32) = 32
> > write(1, "data collection: \t\t ( 243) secon"..., 36) = 36
> > write(1, "Offline data collection\n", 24) = 24
> > write(1, "capabilities: \t\t\t (0x5b) ", 25) = 25
> > write(1, "SMART execute Offline immediate."..., 33) = 33
> > write(1, "\t\t\t\t\tAuto Offline data collectio"..., 50) = 50
> > write(1, "\t\t\t\t\tSuspend Offline collection "..., 55) = 55
> > write(1, "\t\t\t\t\tOffline surface scan suppor"..., 37) = 37
> > write(1, "\t\t\t\t\tSelf-test supported.\n", 26) = 26
> > write(1, "\t\t\t\t\tNo Conveyance Self-test sup"..., 40) = 40
> > write(1, "\t\t\t\t\tSelective Self-test support"..., 36) = 36
> > write(1, "SMART capabilities: ", 31) = 31
> > write(1, "(0x0003)\t", 9) = 9
> > write(1, "Saves SMART data before entering"..., 57) = 57
> > write(1, "\t\t\t\t\tSupports SMART auto save ti"..., 37) = 37
> > write(1, "Error logging capability: ", 32) = 32
> > write(1, " (0x01)\tError logging supported."..., 33) = 33
> > write(1, "\t\t\t\t\tNo General Purpose Logging "..., 41) = 41
> > write(1, "Short self-test routine \n", 25) = 25
> > write(1, "recommended polling time: \t ( "..., 44) = 44
> > write(1, "Extended self-test routine\n", 27) = 27
> > write(1, "recommended polling time: \t ( 9"..., 44) = 44
> > write(1, "\n", 1) = 1
> > write(1, "SMART Attributes Data Structure "..., 52) = 52
> > write(1, "Vendor Specific SMART Attributes"..., 50) = 50
> > write(1, "ID# ATTRIBUTE_NAME FLAG"..., 97) = 97
> > write(1, " 3 Spin_Up_Time ", 28) = 28
> > write(1, "0x0027 252 252 063 Pre-"..., 59) = 59
> > write(1, "5945\n", 5) = 5
> > write(1, " 4 Start_Stop_Count ", 28) = 28
> > write(1, "0x0032 253 253 000 Old_"..., 59) = 59
> > write(1, "17\n", 3) = 3
> > write(1, " 5 Reallocated_Sector_Ct ", 28) = 28
> > write(1, "0x0033 253 253 063 Pre-"..., 59) = 59
> > write(1, "1\n", 2) = 2
> > write(1, " 6 Read_Channel_Margin ", 28) = 28
> > write(1, "0x0001 253 253 100 Pre-"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, " 7 Seek_Error_Rate ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, " 8 Seek_Time_Performance ", 28) = 28
> > write(1, "0x0027 251 248 187 Pre-"..., 59) = 59
> > write(1, "47575\n", 6) = 6
> > write(1, " 9 Power_On_Minutes ", 28) = 28
> > write(1, "0x0032 220 220 000 Old_"..., 59) = 59
> > write(1, "849h+05m\n", 9) = 9
> > write(1, " 10 Spin_Retry_Count ", 28) = 28
> > write(1, "0x002b 252 252 157 Pre-"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, " 11 Calibration_Retry_Count ", 28) = 28
> > write(1, "0x002b 253 252 223 Pre-"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, " 12 Power_Cycle_Count ", 28) = 28
> > write(1, "0x0032 253 253 000 Old_"..., 59) = 59
> > write(1, "19\n", 3) = 3
> > write(1, "192 Power-Off_Retract_Count ", 28) = 28
> > write(1, "0x0032 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "193 Load_Cycle_Count ", 28) = 28
> > write(1, "0x0032 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "194 Temperature_Celsius ", 28) = 28
> > write(1, "0x0032 253 253 000 Old_"..., 59) = 59
> > write(1, "12\n", 3) = 3
> > write(1, "195 Hardware_ECC_Recovered ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "5743\n", 5) = 5
> > write(1, "196 Reallocated_Event_Count ", 28) = 28
> > write(1, "0x0008 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "197 Current_Pending_Sector ", 28) = 28
> > write(1, "0x0008 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "198 Offline_Uncorrectable ", 28) = 28
> > write(1, "0x0008 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "199 UDMA_CRC_Error_Count ", 28) = 28
> > write(1, "0x0008 199 199 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "200 Multi_Zone_Error_Rate ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "201 Soft_Read_Error_Rate ", 28) = 28
> > write(1, "0x000a 253 251 000 Old_"..., 59) = 59
> > write(1, "5\n", 2) = 2
> > write(1, "202 TA_Increase_Count ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "203 Run_Out_Cancel ", 28) = 28
> > write(1, "0x000b 253 252 180 Pre-"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "204 Shock_Count_Write_Opern ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "205 Shock_Rate_Write_Opern ", 28) = 28
> > write(1, "0x000a 253 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "207 Spin_High_Current ", 28) = 28
> > write(1, "0x002a 252 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "208 Spin_Buzz ", 28) = 28
> > write(1, "0x002a 252 252 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "209 Offline_Seek_Performnce ", 28) = 28
> > write(1, "0x0024 196 191 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, " 99 Unknown_Attribute ", 28) = 28
> > write(1, "0x0004 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "100 Unknown_Attribute ", 28) = 28
> > write(1, "0x0004 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "101 Unknown_Attribute ", 28) = 28
> > write(1, "0x0004 253 253 000 Old_"..., 59) = 59
> > write(1, "0\n", 2) = 2
> > write(1, "\n", 1) = 1
> > ioctl(3, FIBMAP, 0xbfffe290) = 0
> > write(1, "SMART Error Log Version: 1\n", 27) = 27
> > write(1, "ATA Error Count: 1\n", 19) = 19
> > write(1, "\tCR = Command Register [HEX]\n\tFR"..., 490) = 490
> > write(1, "Error 1 occurred at disk power-o"..., 77) = 77
> > write(1, " When the command that caused t"..., 88) = 88
> > write(1, " After command completion occur"..., 121) = 121
> > write(1, " Error: UNC 3 sectors at LBA = "..., 51) = 51
> > write(1, "\n\n", 2) = 2
> > write(1, " Commands leading to the comman"..., 194) = 194
> > write(1, " 25 00 08 bb bc 0c e0 00 23d+0"..., 58) = 58
> > write(1, " 25 00 10 83 bc 0c e0 00 23d+0"..., 58) = 58
> > write(1, " 25 00 08 3b bc 0c e0 00 23d+0"..., 58) = 58
> > write(1, " 25 00 08 33 bc 0c e0 00 23d+0"..., 58) = 58
> > write(1, " 25 00 08 13 bc 0c e0 00 23d+0"..., 58) = 58
> > write(1, "\n", 1) = 1
> > ioctl(3, FIBMAP, 0xbfffe2a0) = 0
> > write(1, "SMART Self-test log structure re"..., 48) = 48
> > write(1, "Num Test_Description Status "..., 96) = 96
> > write(1, "# 1 Short offline Complet"..., 79) = 79
> > write(1, "# 2 Short offline Complet"..., 79) = 79
> > write(1, "# 3 Short offline Complet"..., 79) = 79
> > write(1, "# 4 Short offline Complet"..., 79) = 79
> > write(1, "# 5 Short offline Complet"..., 79) = 79
> > write(1, "# 6 Extended offline Complet"..., 79) = 79
> > write(1, "# 7 Short offline Complet"..., 79) = 79
> > write(1, "# 8 Short offline Complet"..., 79) = 79
> > write(1, "# 9 Short offline Complet"..., 79) = 79
> > write(1, "#10 Short offline Complet"..., 79) = 79
> > write(1, "#11 Short offline Complet"..., 79) = 79
> > write(1, "#12 Short offline Complet"..., 79) = 79
> > write(1, "#13 Extended offline Complet"..., 79) = 79
> > write(1, "#14 Short offline Complet"..., 79) = 79
> > write(1, "#15 Short offline Complet"..., 79) = 79
> > write(1, "#16 Short offline Complet"..., 79) = 79
> > write(1, "#17 Short offline Complet"..., 79) = 79
> > write(1, "#18 Short offline Complet"..., 79) = 79
> > write(1, "#19 Short offline Complet"..., 79) = 79
> > write(1, "#20 Extended offline Complet"..., 79) = 79
> > write(1, "#21 Short offline Complet"..., 79) = 79
> > write(1, "\n", 1) = 1
> > ioctl(3, FIBMAP, 0xbfffe290) = 0
> > write(1, "SMART Selective self-test log da"..., 63) = 63
> > write(1, " SPAN MIN_LBA MAX_LBA CURRENT"..., 45) = 45
> > write(1, " 1 0 0 Not_tes"..., 37) = 37
> > write(1, " 2 0 0 Not_tes"..., 37) = 37
> > write(1, " 3 0 0 Not_tes"..., 37) = 37
> > write(1, " 4 0 0 Not_tes"..., 37) = 37
> > write(1, " 5 0 0 Not_tes"..., 37) = 37
> > write(1, "Selective self-test flags (0x0):"..., 33) = 33
> > write(1, " After scanning selected spans,"..., 69) = 69
> > write(1, "If Selective self-test is pendin"..., 76) = 76
> > write(1, "\n", 1) = 1
> > munmap(0x40018000, 4096) = 0
> > exit_group(64) = ?
>
> Cheers,
> Kyle Moffett
>
> -----BEGIN GEEK CODE BLOCK-----
> Version: 3.12
> GCM/CS/IT/U d- s++: a18 C++++>$ UB/L/X/*++++(+)>$ P+++(++++)>$
> L++++(+++) E W++(+) N+++(++) o? K? w--- O? M++ V? PS+() PE+(-) Y+
> PGP+++ t+(+++) 5 X R? tv-(--) b++++(++) DI+ D+ G e->++++$ h!*()>++$ r
> !y?(-)
> ------END GEEK CODE BLOCK------
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
next prev parent reply other threads:[~2005-04-15 22:53 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-04-15 22:26 SCSI opcode 0x80 and 3ware Escalade 7000 ATA RAID Kyle Moffett
2005-04-15 22:50 ` adam radford [this message]
2005-04-15 23:55 ` Kyle Moffett
2005-04-16 10:52 ` Jurgen Kramer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b1bc6a0005041515505419ba1e@mail.gmail.com \
--to=aradford@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mrmacman_g4@mac.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.