From: bugzilla-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 111381] New: mvsas 0.8.16 on Marvell 88SE9485 reports timeouts on load
Date: Wed, 27 Jan 2016 21:56:17 +0000 [thread overview]
Message-ID: <bug-111381-11613@https.bugzilla.kernel.org/> (raw)
https://bugzilla.kernel.org/show_bug.cgi?id=111381
Bug ID: 111381
Summary: mvsas 0.8.16 on Marvell 88SE9485 reports timeouts on
load
Product: SCSI Drivers
Version: 2.5
Kernel Version: 4.1.15
Hardware: x86-64
OS: Linux
Tree: Mainline
Status: NEW
Severity: high
Priority: P1
Component: Other
Assignee: scsi_drivers-other@kernel-bugs.osdl.org
Reporter: gdevenyi@gmail.com
Regression: No
Motherboard: P9A-I/C2550/SAS/4L
lsscsi -t -v:
[0:0:0:0] disk sas:0x5000c50034367baa /dev/sdb
dir: /sys/bus/scsi/devices/0:0:0:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:0/end_device-0:0/target0:0:0/0:0:0:0]
[0:0:1:0] disk sas:0x5000c50034367ba9 /dev/sdc
dir: /sys/bus/scsi/devices/0:0:1:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:1/end_device-0:1/target0:0:1/0:0:1:0]
[0:0:2:0] disk sas:0x5000c5003432eafe /dev/sdd
dir: /sys/bus/scsi/devices/0:0:2:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:2/end_device-0:2/target0:0:2/0:0:2:0]
[0:0:3:0] disk sas:0x5000c5003432eafd /dev/sde
dir: /sys/bus/scsi/devices/0:0:3:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:3/end_device-0:3/target0:0:3/0:0:3:0]
[0:0:4:0] disk sas:0x5000c500741d842a /dev/sdf
dir: /sys/bus/scsi/devices/0:0:4:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:4/end_device-0:4/target0:0:4/0:0:4:0]
[0:0:5:0] disk sas:0x5000c500741d8429 /dev/sdg
dir: /sys/bus/scsi/devices/0:0:5:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:5/end_device-0:5/target0:0:5/0:0:5:0]
[0:0:6:0] disk sas:0x5000c5003c9335ca /dev/sdh
dir: /sys/bus/scsi/devices/0:0:6:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:6/end_device-0:6/target0:0:6/0:0:6:0]
[0:0:7:0] disk sas:0x5000c5003c9335c9 /dev/sdi
dir: /sys/bus/scsi/devices/0:0:7:0
[/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:7/end_device-0:7/target0:0:7/0:0:7:0]
[2:0:0:0] disk sata: /dev/sda
dir: /sys/bus/scsi/devices/2:0:0:0
[/sys/devices/pci0000:00/0000:00:18.0/ata2/host2/target2:0:0/2:0:0:0]
[3:0:0:0] disk sas:0x5000c5005d722942 /dev/sdj
dir: /sys/bus/scsi/devices/3:0:0:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:0/end_device-3:0/target3:0:0/3:0:0:0]
[3:0:1:0] disk sas:0x5000c5005d722941 /dev/sdk
dir: /sys/bus/scsi/devices/3:0:1:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:1/end_device-3:1/target3:0:1/3:0:1:0]
[3:0:2:0] disk sas:0x5000c5005d84e1a6 /dev/sdl
dir: /sys/bus/scsi/devices/3:0:2:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:2/end_device-3:2/target3:0:2/3:0:2:0]
[3:0:3:0] disk sas:0x5000c5005d84e1a5 /dev/sdm
dir: /sys/bus/scsi/devices/3:0:3:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:3/end_device-3:3/target3:0:3/3:0:3:0]
[3:0:4:0] disk sas:0x5000c5007408d282 /dev/sdn
dir: /sys/bus/scsi/devices/3:0:4:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:4/end_device-3:4/target3:0:4/3:0:4:0]
[3:0:5:0] disk sas:0x5000c5007408d281 /dev/sdo
dir: /sys/bus/scsi/devices/3:0:5:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:5/end_device-3:5/target3:0:5/3:0:5:0]
[3:0:6:0] disk sas:0x5000c500740c1212 /dev/sdp
dir: /sys/bus/scsi/devices/3:0:6:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:6/end_device-3:6/target3:0:6/3:0:6:0]
[3:0:7:0] disk sas:0x5000c500740c1211 /dev/sdq
dir: /sys/bus/scsi/devices/3:0:7:0
[/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:7/end_device-3:7/target3:0:7/3:0:7:0]
[4:0:0:0] cd/dvd usb: 1-1.3.2:1.0 /dev/sr0
dir: /sys/bus/scsi/devices/4:0:0:0
[/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.2/1-1.3.2:1.0/host4/target4:0:0/4:0:0:0]
[5:0:0:0] disk usb: 1-1.3.3:1.0 /dev/sdr
dir: /sys/bus/scsi/devices/5:0:0:0
[/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.3/1-1.3.3:1.0/host5/target5:0:0/5:0:0:0]
[6:0:0:0] disk usb: 1-1.3.4:1.0 /dev/sds
dir: /sys/bus/scsi/devices/6:0:0:0
[/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/host6/target6:0:0/6:0:0:0]
Relevant dmesg snip:
[ 1.274088] mvsas 0000:02:00.0: mvsas: driver version 0.8.16
[ 1.276086] dca service started, version 1.12.1
[ 1.296857] mvsas 0000:02:00.0: mvsas: PCI-E x4, Bandwidth Usage: 5.0 Gbps
[ 1.303168] ahci 0000:00:18.0: version 3.0
[ 1.303887] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.15-k
[ 1.310071] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.318636] ahci 0000:00:18.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3
impl SATA mode
[ 1.325008] ahci 0000:00:18.0: flags: 64bit ncq led clo pio deso sadm sds
apst
[ 1.332076] scsi host1: ahci
[ 1.338704] scsi host2: ahci
[ 1.345099] ata1: SATA max UDMA/133 abar m2048@0xde412000 port 0xde412100
irq 28
[ 1.351516] ata2: SATA max UDMA/133 abar m2048@0xde412000 port 0xde412180
irq 28
[ 1.535197] usb 1-1: New USB device found, idVendor=8087, idProduct=07db
[ 1.541442] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 1.548138] hub 1-1:1.0: USB hub found
[ 1.554581] hub 1-1:1.0: 4 ports detected
[ 1.682855] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.689116] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.696299] ata2.00: ATA-9: TS32GMTS400, N1126I, max UDMA/133
[ 1.700761] igb 0000:00:14.0: added PHC on eth0
[ 1.700763] igb 0000:00:14.0: Intel(R) Gigabit Ethernet Network Connection
[ 1.700866] igb 0000:00:14.0: eth0: PBA No: 001800-000
[ 1.700868] igb 0000:00:14.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx
queue(s)
[ 1.727495] ata2.00: 62533296 sectors, multi 2: LBA48 NCQ (depth 31/32), AA
[ 1.734384] ata2.00: configured for UDMA/133
[ 1.740435] tsc: Refined TSC clocksource calibration: 2393.903 MHz
[ 1.740675] scsi 2:0:0:0: Direct-Access ATA TS32GMTS400 6I
PQ: 0 ANSI: 5
[ 1.741127] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1.741163] sd 2:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0
GB/29.8 GiB)
[ 1.741356] sd 2:0:0:0: [sda] Write Protect is off
[ 1.741359] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.741416] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.771415] sda: sda1 sda2 sda3
[ 1.772620] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.795221] clocksource tsc: mask: 0xffffffffffffffff max_cycles:
0x2281b7b41ef, max_idle_ns: 440795228866 ns
[ 1.848857] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
[ 1.854997] EXT4-fs (sda2): write access will be enabled during recovery
[ 1.862974] usb 1-1.2: new low-speed USB device number 3 using ehci-pci
[ 2.048981] igb 0000:00:14.1: added PHC on eth1
[ 2.055033] igb 0000:00:14.1: Intel(R) Gigabit Ethernet Network Connection
[ 2.061179] igb 0000:00:14.1: eth1: PBA No: 001800-000
[ 2.067121] igb 0000:00:14.1: Using MSI-X interrupts. 4 rx queue(s), 4 tx
queue(s)
[ 2.073980] usb 1-1.2: New USB device found, idVendor=051d, idProduct=0002
[ 2.080015] usb 1-1.2: New USB device strings: Mfr=3, Product=1,
SerialNumber=2
[ 2.086172] usb 1-1.2: Product: Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8
[ 2.092281] usb 1-1.2: Manufacturer: American Power Conversion
[ 2.098478] usb 1-1.2: SerialNumber: BB0820012670
[ 2.112737] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.148885] EXT4-fs (sda2): orphan cleanup on readonly fs
[ 2.155061] EXT4-fs (sda2): 2 orphan inodes deleted
[ 2.161145] EXT4-fs (sda2): recovery complete
[ 2.176864] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
(null)
[ 2.183027] usb 1-1.3: new high-speed USB device number 4 using ehci-pci
[ 2.425276] igb 0000:00:14.2: added PHC on eth2
[ 2.431530] igb 0000:00:14.2: Intel(R) Gigabit Ethernet Network Connection
[ 2.438023] igb 0000:00:14.2: eth2: PBA No: 001800-000
[ 2.444316] igb 0000:00:14.2: Using MSI-X interrupts. 4 rx queue(s), 4 tx
queue(s)
[ 2.485000] usb 1-1.3: New USB device found, idVendor=046b, idProduct=ff01
[ 2.491400] usb 1-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 2.497736] usb 1-1.3: Product: Virtual Hub
[ 2.503956] usb 1-1.3: Manufacturer: American Megatrends Inc.
[ 2.510176] usb 1-1.3: SerialNumber: serial
[ 2.516878] hub 1-1.3:1.0: USB hub found
[ 2.522991] hub 1-1.3:1.0: 5 ports detected
[ 2.712822] usbcore: registered new interface driver usbhid
[ 2.718787] usbhid: USB HID core driver
[ 2.797332] igb 0000:00:14.3: added PHC on eth3
[ 2.803157] igb 0000:00:14.3: Intel(R) Gigabit Ethernet Network Connection
[ 2.808999] igb 0000:00:14.3: eth3: PBA No: 001800-000
[ 2.814722] igb 0000:00:14.3: Using MSI-X interrupts. 4 rx queue(s), 4 tx
queue(s)
[ 2.821282] Switched to clocksource tsc
[ 2.851520] usb 1-1.3.1: new low-speed USB device number 5 using ehci-pci
[ 3.012794] usb 1-1.3.1: New USB device found, idVendor=046b, idProduct=ff10
[ 3.018561] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 3.024327] usb 1-1.3.1: Product: Virtual Keyboard and Mouse
[ 3.030071] usb 1-1.3.1: Manufacturer: American Megatrends Inc.
[ 3.159691] usb 1-1.3.2: new high-speed USB device number 6 using ehci-pci
[ 3.320714] usb 1-1.3.2: New USB device found, idVendor=046b, idProduct=ff20
[ 3.326434] usb 1-1.3.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 3.332120] usb 1-1.3.2: Product: Virtual Cdrom Device
[ 3.337745] usb 1-1.3.2: Manufacturer: American Megatrends Inc.
[ 3.343394] usb 1-1.3.2: SerialNumber: AAAABBBBCCCC1
[ 3.475869] usb 1-1.3.3: new high-speed USB device number 7 using ehci-pci
[ 3.636901] usb 1-1.3.3: New USB device found, idVendor=046b, idProduct=ff40
[ 3.642636] usb 1-1.3.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 3.648426] usb 1-1.3.3: Product: Virtual Floppy Device
[ 3.654156] usb 1-1.3.3: Manufacturer: American Megatrends Inc.
[ 3.659810] usb 1-1.3.3: SerialNumber: AAAABBBBCCCC2
[ 3.788051] usb 1-1.3.4: new high-speed USB device number 8 using ehci-pci
[ 3.949074] usb 1-1.3.4: New USB device found, idVendor=046b, idProduct=ff31
[ 3.954635] usb 1-1.3.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 3.960087] usb 1-1.3.4: Product: Virtual HardDisk Device
[ 3.965503] usb 1-1.3.4: Manufacturer: American Megatrends Inc.
[ 3.970899] usb 1-1.3.4: SerialNumber: AAAABBBBCCCC3
[ 8.691723] scsi host0: mvsas
[ 8.697850] mvsas 0000:01:00.0: mvsas: driver version 0.8.16
[ 8.703663] mvsas 0000:01:00.0: mvsas: PCI-E x4, Bandwidth Usage: 5.0 Gbps
[ 8.707897] sas: phy-0:0 added to port-0:0, phy_mask:0x1 (5000c50034367baa)
[ 8.707900] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 1
[ 8.727818] sas: phy-0:1 added to port-0:1, phy_mask:0x2 (5000c50034367ba9)
[ 8.727823] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 2
[ 8.757662] sas: phy-0:2 added to port-0:2, phy_mask:0x4 (5000c5003432eafe)
[ 8.757665] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 4
[ 8.797395] sas: DOING DISCOVERY on port 0, pid:155
[ 8.797399] sas: DONE DISCOVERY on port 0, pid:155, result:0
[ 8.797448] sas: phy-0:3 added to port-0:3, phy_mask:0x8 (5000c5003432eafd)
[ 8.797451] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 8
[ 8.847156] sas: phy-0:4 added to port-0:4, phy_mask:0x1 (5000c500741d842a)
[ 8.847160] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 1
[ 8.867071] sas: phy-0:5 added to port-0:5, phy_mask:0x2 (5000c500741d8429)
[ 8.867074] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 2
[ 8.896874] sas: DOING DISCOVERY on port 1, pid:155
[ 8.896877] sas: DONE DISCOVERY on port 1, pid:155, result:0
[ 8.896927] sas: phy-0:6 added to port-0:6, phy_mask:0x4 (5000c5003c9335ca)
[ 8.896930] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 4
[ 8.936699] sas: phy-0:7 added to port-0:7, phy_mask:0x8 (5000c5003c9335c9)
[ 8.936702] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 8
[ 8.986359] sas: DOING DISCOVERY on port 2, pid:155
[ 8.986363] sas: DONE DISCOVERY on port 2, pid:155, result:0
[ 8.987647] scsi 0:0:0:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 8.995126] sas: DOING DISCOVERY on port 3, pid:155
[ 8.995136] sas: DONE DISCOVERY on port 3, pid:155, result:0
[ 8.995145] sas: DOING DISCOVERY on port 4, pid:155
[ 8.995149] sas: DONE DISCOVERY on port 4, pid:155, result:0
[ 8.995161] sas: DOING DISCOVERY on port 5, pid:155
[ 8.995166] sas: DONE DISCOVERY on port 5, pid:155, result:0
[ 8.996181] scsi 0:0:1:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 9.003056] sas: DOING DISCOVERY on port 6, pid:155
[ 9.003062] sas: DONE DISCOVERY on port 6, pid:155, result:0
[ 9.003071] sas: DOING DISCOVERY on port 7, pid:155
[ 9.003074] sas: DONE DISCOVERY on port 7, pid:155, result:0
[ 9.004324] scsi 0:0:2:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 9.012459] scsi 0:0:3:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 9.020051] scsi 0:0:4:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 9.026562] scsi 0:0:5:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 9.033522] scsi 0:0:6:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 9.040745] scsi 0:0:7:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 9.047242] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 9.052400] sd 0:0:1:0: Attached scsi generic sg2 type 0
[ 9.052502] sd 0:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.053230] sd 0:0:1:0: [sdc] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.057101] sd 0:0:0:0: [sdb] Write Protect is off
[ 9.057104] sd 0:0:0:0: [sdb] Mode Sense: d7 00 10 08
[ 9.058949] sd 0:0:1:0: [sdc] Write Protect is off
[ 9.058952] sd 0:0:1:0: [sdc] Mode Sense: d7 00 10 08
[ 9.059533] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.061023] sd 0:0:1:0: [sdc] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.077443] sdb: sdb1 sdb9
[ 9.080843] sdc: sdc1 sdc9
[ 9.090572] sd 0:0:0:0: [sdb] Attached SCSI disk
[ 9.091371] sd 0:0:1:0: [sdc] Attached SCSI disk
[ 9.101422] sd 0:0:2:0: Attached scsi generic sg3 type 0
[ 9.105866] sd 0:0:3:0: Attached scsi generic sg4 type 0
[ 9.106006] sd 0:0:2:0: [sdd] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.106774] sd 0:0:3:0: [sde] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.109925] sd 0:0:2:0: [sdd] Write Protect is off
[ 9.109928] sd 0:0:2:0: [sdd] Mode Sense: d7 00 10 08
[ 9.111779] sd 0:0:3:0: [sde] Write Protect is off
[ 9.111782] sd 0:0:3:0: [sde] Mode Sense: d7 00 10 08
[ 9.112379] sd 0:0:2:0: [sdd] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.113844] sd 0:0:3:0: [sde] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.133888] sd 0:0:4:0: Attached scsi generic sg5 type 0
[ 9.134050] sd 0:0:4:0: [sdf] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.137751] sd 0:0:4:0: [sdf] Write Protect is off
[ 9.137754] sd 0:0:4:0: [sdf] Mode Sense: d7 00 10 08
[ 9.138307] sd 0:0:4:0: [sdf] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.138761] sdd: sdd1 sdd9
[ 9.142160] sde: sde1 sde9
[ 9.146352] random: nonblocking pool is initialized
[ 9.154838] sd 0:0:2:0: [sdd] Attached SCSI disk
[ 9.156295] sd 0:0:3:0: [sde] Attached SCSI disk
[ 9.168918] sd 0:0:5:0: Attached scsi generic sg6 type 0
[ 9.172961] sd 0:0:6:0: Attached scsi generic sg7 type 0
[ 9.173030] sd 0:0:5:0: [sdg] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.173418] sd 0:0:6:0: [sdh] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.173786] sdf: sdf1 sdf9
[ 9.176797] sd 0:0:5:0: [sdg] Write Protect is off
[ 9.176800] sd 0:0:5:0: [sdg] Mode Sense: d7 00 10 08
[ 9.177650] sd 0:0:6:0: [sdh] Write Protect is off
[ 9.177653] sd 0:0:6:0: [sdh] Mode Sense: d7 00 10 08
[ 9.177853] sd 0:0:5:0: [sdg] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.181519] sd 0:0:6:0: [sdh] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.182154] sd 0:0:4:0: [sdf] Attached SCSI disk
[ 9.192969] sdg: sdg1 sdg9
[ 9.202032] sd 0:0:5:0: [sdg] Attached SCSI disk
[ 9.202056] sdh: sdh1 sdh9
[ 9.212823] sd 0:0:6:0: [sdh] Attached SCSI disk
[ 9.226675] sd 0:0:7:0: Attached scsi generic sg8 type 0
[ 9.227054] sd 0:0:7:0: [sdi] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 9.236118] sd 0:0:7:0: [sdi] Write Protect is off
[ 9.240479] sd 0:0:7:0: [sdi] Mode Sense: d7 00 10 08
[ 9.241806] sd 0:0:7:0: [sdi] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 9.253848] sdi: sdi1 sdi9
[ 9.263261] sd 0:0:7:0: [sdi] Attached SCSI disk
[ 16.099998] scsi host3: mvsas
[ 16.175273] sas: phy-3:0 added to port-3:0, phy_mask:0x1 (5000c5005d722942)
[ 16.175277] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 1
[ 16.195203] sas: phy-3:1 added to port-3:1, phy_mask:0x2 (5000c5005d722941)
[ 16.195206] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 2
[ 16.225049] sas: phy-3:2 added to port-3:2, phy_mask:0x4 (5000c5005d84e1a6)
[ 16.225052] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 4
[ 16.264821] sas: phy-3:3 added to port-3:3, phy_mask:0x8 (5000c5005d84e1a5)
[ 16.264824] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 8
[ 16.314519] sas: phy-3:4 added to port-3:4, phy_mask:0x1 (5000c5007408d282)
[ 16.314523] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 1
[ 16.334436] sas: phy-3:5 added to port-3:5, phy_mask:0x2 (5000c5007408d281)
[ 16.334439] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 2
[ 16.364281] sas: phy-3:6 added to port-3:6, phy_mask:0x4 (5000c500740c1212)
[ 16.364285] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 4
[ 16.404052] sas: phy-3:7 added to port-3:7, phy_mask:0x8 (5000c500740c1211)
[ 16.404055] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide
port phy map 8
[ 16.453711] sas: DOING DISCOVERY on port 0, pid:6
[ 16.453716] sas: DONE DISCOVERY on port 0, pid:6, result:0
[ 16.453725] sas: DOING DISCOVERY on port 1, pid:6
[ 16.453728] sas: DONE DISCOVERY on port 1, pid:6, result:0
[ 16.453735] sas: DOING DISCOVERY on port 2, pid:6
[ 16.453740] sas: DONE DISCOVERY on port 2, pid:6, result:0
[ 16.453747] sas: DOING DISCOVERY on port 3, pid:6
[ 16.453751] sas: DONE DISCOVERY on port 3, pid:6, result:0
[ 16.453757] sas: DOING DISCOVERY on port 4, pid:6
[ 16.453760] sas: DONE DISCOVERY on port 4, pid:6, result:0
[ 16.453767] sas: DOING DISCOVERY on port 5, pid:6
[ 16.453771] sas: DONE DISCOVERY on port 5, pid:6, result:0
[ 16.453780] sas: DOING DISCOVERY on port 6, pid:6
[ 16.453785] sas: DONE DISCOVERY on port 6, pid:6, result:0
[ 16.453791] sas: DOING DISCOVERY on port 7, pid:6
[ 16.453794] sas: DONE DISCOVERY on port 7, pid:6, result:0
[ 16.454955] scsi 3:0:0:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 16.462566] scsi 3:0:1:0: Direct-Access SEAGATE ST32000444SS 0006
PQ: 0 ANSI: 5
[ 16.469684] scsi 3:0:2:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.475938] scsi 3:0:3:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.482286] scsi 3:0:4:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.488166] scsi 3:0:5:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.494331] scsi 3:0:6:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.500037] scsi 3:0:7:0: Direct-Access SEAGATE ST2000NM0001 0002
PQ: 0 ANSI: 6
[ 16.505321] sd 3:0:0:0: Attached scsi generic sg9 type 0
[ 16.505715] sd 3:0:0:0: [sdj] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.509529] sd 3:0:0:0: [sdj] Write Protect is off
[ 16.509532] sd 3:0:0:0: [sdj] Mode Sense: d7 00 10 08
[ 16.510861] sd 3:0:0:0: [sdj] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.522593] sd 3:0:1:0: Attached scsi generic sg10 type 0
[ 16.522759] sdj: sdj1 sdj9
[ 16.523057] sd 3:0:1:0: [sdk] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.528211] sd 3:0:1:0: [sdk] Write Protect is off
[ 16.528214] sd 3:0:1:0: [sdk] Mode Sense: d7 00 10 08
[ 16.530029] sd 3:0:1:0: [sdk] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.535869] sd 3:0:0:0: [sdj] Attached SCSI disk
[ 16.545809] sdk: sdk1 sdk9
[ 16.553421] sd 3:0:1:0: [sdk] Attached SCSI disk
[ 16.559721] sd 3:0:2:0: Attached scsi generic sg11 type 0
[ 16.559930] sd 3:0:2:0: [sdl] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.560876] sd 3:0:2:0: [sdl] Write Protect is off
[ 16.560880] sd 3:0:2:0: [sdl] Mode Sense: d7 00 10 08
[ 16.561424] sd 3:0:2:0: [sdl] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.579652] sd 3:0:3:0: Attached scsi generic sg12 type 0
[ 16.584941] sd 3:0:4:0: Attached scsi generic sg13 type 0
[ 16.585205] sd 3:0:4:0: [sdn] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.590244] sd 3:0:4:0: [sdn] Write Protect is off
[ 16.590247] sd 3:0:4:0: [sdn] Mode Sense: d7 00 10 08
[ 16.590820] sd 3:0:4:0: [sdn] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.595308] sd 3:0:3:0: [sdm] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.595927] sdl: sdl1 sdl9
[ 16.599987] sd 3:0:3:0: [sdm] Write Protect is off
[ 16.599996] sd 3:0:3:0: [sdm] Mode Sense: d7 00 10 08
[ 16.601006] sd 3:0:3:0: [sdm] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.611179] sd 3:0:2:0: [sdl] Attached SCSI disk
[ 16.621188] sdm: sdm1 sdm9
[ 16.621920] sdn: sdn1 sdn9
[ 16.631919] sd 3:0:3:0: [sdm] Attached SCSI disk
[ 16.641101] sd 3:0:4:0: [sdn] Attached SCSI disk
[ 16.651243] sd 3:0:5:0: Attached scsi generic sg14 type 0
[ 16.651458] sd 3:0:5:0: [sdo] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.652367] sd 3:0:5:0: [sdo] Write Protect is off
[ 16.652370] sd 3:0:5:0: [sdo] Mode Sense: d7 00 10 08
[ 16.656289] sd 3:0:5:0: [sdo] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.672397] sdo: sdo1 sdo9
[ 16.672628] sd 3:0:6:0: Attached scsi generic sg15 type 0
[ 16.672895] sd 3:0:6:0: [sdp] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.672926] sd 3:0:7:0: Attached scsi generic sg16 type 0
[ 16.673456] sd 3:0:7:0: [sdq] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 16.674218] sd 3:0:6:0: [sdp] Write Protect is off
[ 16.674222] sd 3:0:6:0: [sdp] Mode Sense: d7 00 10 08
[ 16.678415] sd 3:0:6:0: [sdp] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.678646] sd 3:0:7:0: [sdq] Write Protect is off
[ 16.678649] sd 3:0:7:0: [sdq] Mode Sense: d7 00 10 08
[ 16.679391] sd 3:0:7:0: [sdq] Write cache: enabled, read cache: enabled,
supports DPO and FUA
[ 16.718785] sdp: sdp1 sdp9
[ 16.718975] sdq: sdq1 sdq9
[ 16.732110] sd 3:0:6:0: [sdp] Attached SCSI disk
[ 16.741467] sd 3:0:7:0: [sdq] Attached SCSI disk
[ 16.747488] sd 3:0:5:0: [sdo] Attached SCSI disk
And finally reported errors on load:
[ 2007.415225] sd 0:0:6:0: [sdh] tag#0 FAILED Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2007.415239] sd 0:0:6:0: [sdh] tag#0 Sense Key : Aborted Command [current]
[ 2007.415246] sd 0:0:6:0: [sdh] tag#0 Add. Sense: Ack/nak timeout
[ 2007.415252] sd 0:0:6:0: [sdh] tag#0 CDB: Read(10) 28 00 2d 02 9d 24 00 00 dc
00
[ 2007.415257] blk_update_request: I/O error, dev sdh, sector 755146020
[ 2958.428448] sd 0:0:6:0: [sdh] tag#0 FAILED Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[ 2958.428466] sd 0:0:6:0: [sdh] tag#0 Sense Key : Aborted Command [current]
[ 2958.428474] sd 0:0:6:0: [sdh] tag#0 Add. Sense: Ack/nak timeout
[ 2958.428481] sd 0:0:6:0: [sdh] tag#0 CDB: Read(10) 28 00 08 fe 2f c9 00 00 dd
00
[ 2958.428486] blk_update_request: I/O error, dev sdh, sector 150876105
--
You are receiving this mail because:
You are watching the assignee of the bug.
next reply other threads:[~2016-01-27 21:56 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-27 21:56 bugzilla-daemon [this message]
2016-01-27 22:02 ` [Bug 111381] New: mvsas 0.8.16 on Marvell 88SE9485 reports timeouts on load James Bottomley
2016-01-27 22:18 ` [Bug 111381] " bugzilla-daemon
2016-01-28 0:37 ` bugzilla-daemon
2016-01-28 0:47 ` James Bottomley
2016-02-05 16:33 ` bugzilla-daemon
2016-02-08 17:24 ` bugzilla-daemon
2016-02-09 0:11 ` [Bug 111381] mvsas 0.8.16 on Marvell 88SE9485 reports timeouts on load with SMART commands bugzilla-daemon
2016-04-01 18:56 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bug-111381-11613@https.bugzilla.kernel.org/ \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.