From: bugzilla-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 209177] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10791/_scsih_probe()!
Date: Tue, 29 Sep 2020 19:59:17 +0000 [thread overview]
Message-ID: <bug-209177-11613-OSE9e4xQRI@https.bugzilla.kernel.org/> (raw)
In-Reply-To: <bug-209177-11613@https.bugzilla.kernel.org/>
https://bugzilla.kernel.org/show_bug.cgi?id=209177
--- Comment #1 from sun.nagarajan@gmail.com ---
Kernel version 5.8.12 with the following patches were suggested by Suganath
Prabu Subramani on Sep-29-2020:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/scsi/mpt3sas?h=v5.9-rc4&id=61e6ba03ea26f0205e535862009ff6ffdbf4de0c
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/scsi/mpt3sas?h=v5.9-rc4&id=f56577e8c7d0f3054f97d1f0d1cbe9a4d179cc47
I built kernel version 5.8.12, and these patches were already applied.
The problem still exists.
EDITED dmesg output below:
[ 10.110816] mpt2sas_cm0: mpt3sas_base_attach
[ 10.110913] dca service started, version 1.12.1
[ 10.122668] mpt2sas_cm0: mpt3sas_base_map_resources
[ 10.140735] usb 2-1.7: New USB device found, idVendor=1546, idProduct=01a6,
bcdDevice= 7.03
[ 10.147693] scsi host2: ahci
[ 10.163432] usb 2-1.7: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 10.173819] mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem
(197972228 kB)
[ 10.189366] usb 2-1.7: Product: u-blox 6 - GPS Receiver
[ 10.206466] mpt2sas_cm0: _base_get_ioc_facts
[ 10.219986] usb 2-1.7: Manufacturer: u-blox AG - www.u-blox.com
[ 10.246805] mpt2sas_cm0: _base_wait_for_iocstate
[ 10.260177] scsi host3: ahci
[ 10.271074] scsi host4: ahci
[ 10.281958] scsi host5: ahci
[ 10.292565] scsi host6: ahci
[ 10.299138] usb 2-1.8: new full-speed USB device number 6 using ehci-pci
[ 10.303153] scsi host7: ahci
[ 10.328158] ata1: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700100
irq 53
[ 10.343989] ata2: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700180
irq 53
[ 10.359546] ata3: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700200
irq 53
[ 10.374807] ata4: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700280
irq 53
[ 10.389813] ata5: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700300
irq 53
[ 10.404635] ata6: SATA max UDMA/133 abar m2048@0xd1700000 port 0xd1700380
irq 53
[ 10.412371] scsi 0:0:0:0: Direct-Access SanDisk Ultra Fit 1.00
PQ: 0 ANSI: 6
[ 10.433718] usb 2-1.8: New USB device found, idVendor=051d, idProduct=0003,
bcdDevice= 1.06
[ 10.435546] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 10.450887] usb 2-1.8: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 10.464152] offset:data
[ 10.478544] usb 2-1.8: Product: Smart-UPS 2200 FW:UPS 06.3 / MCU 11.0
[ 10.488004] mpt2sas_cm0: [0x00]:03100200
[ 10.488004] mpt2sas_cm0: [0x04]:00002300
[ 10.488005] mpt2sas_cm0: [0x08]:00000000
[ 10.488005] mpt2sas_cm0: [0x0c]:00000000
[ 10.488006] mpt2sas_cm0: [0x10]:00000000
[ 10.488007] mpt2sas_cm0: [0x14]:00010080
[ 10.488007] mpt2sas_cm0: [0x18]:22137ec7
[ 10.488008] mpt2sas_cm0: [0x1c]:0001285c
[ 10.488017] mpt2sas_cm0: [0x20]:14000600
[ 10.501945] usb 2-1.8: Manufacturer: American Power Conversion
[ 10.501961] usb 2-1.8: SerialNumber: JS1051006712
[ 10.513140] mpt2sas_cm0: [0x24]:00000020
[ 10.513140] mpt2sas_cm0: [0x28]:04000020
[ 10.513141] mpt2sas_cm0: [0x2c]:00810080
[ 10.513141] mpt2sas_cm0: [0x30]:007f0003
[ 10.513142] mpt2sas_cm0: [0x34]:0020ffe0
[ 10.513154] mpt2sas_cm0: [0x38]:008004b0
[ 10.513154] mpt2sas_cm0: [0x3c]:00000011
[ 10.513155] mpt2sas_cm0: [0x40]:00000000
[ 10.513156] mpt2sas_cm0: CurrentHostPageSize is 0: Setting default host page
size to 4k
[ 10.524350] sd 0:0:0:0: [sda] 30031250 512-byte logical blocks: (15.4
GB/14.3 GiB)
[ 10.535178] mpt2sas_cm0: CurrentHostPageSize(0)
[ 10.548205] sd 0:0:0:0: [sda] Write Protect is off
[ 10.556610] mpt2sas_cm0: hba queue depth(32455), max chains per io(128)
[ 10.566972] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 10.577132] mpt2sas_cm0: request frame size(128), reply frame size(128)
[ 10.589074] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 10.597175] mpt2sas_cm0: msix is supported, vector_count(1)
[ 10.692084] hid: raw HID events driver (C) Jiri Kosina
[ 10.692148] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
[ 10.692149] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 10.705215] mpt2sas_cm0: MSI-X vectors supported: 1
[ 10.705216] no of cores: 32, max_msix_vectors: -1
[ 10.705217] mpt2sas_cm0: 0 1
[ 10.705359] mpt2sas_cm0: High IOPs queues : disabled
[ 10.757534] ata4: SATA link down (SStatus 0 SControl 300)
[ 10.761609] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 56
[ 10.761611] mpt2sas_cm0: iomem(0x00000000d1380000),
mapped(0x(____ptrval____)), size(16384)
[ 10.761613] mpt2sas_cm0: ioport(0x0000000000002000), size(256)
[ 10.781648] ata1: SATA link down (SStatus 0 SControl 300)
[ 10.793026] mpt2sas_cm0: _base_get_ioc_facts
[ 10.804281] ata6: SATA link down (SStatus 0 SControl 300)
[ 10.817492] mpt2sas_cm0: _base_wait_for_iocstate
[ 10.821742] usbcore: registered new interface driver usbhid
[ 10.821743] usbhid: USB HID core driver
[ 10.829361] ata3: SATA link down (SStatus 0 SControl 300)
[ 10.906674] offset:data
[ 10.917639] ata5: SATA link down (SStatus 0 SControl 300)
[ 10.917791] input: American Megatrends Inc. Virtual Keyboard and Mouse as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/0003:046B:FF10.0001/input/input2
[ 10.917893] hid-generic 0003:046B:FF10.0001: input,hidraw0: USB HID v1.10
Keyboard [American Megatrends Inc. Virtual Keyboard and Mouse] on
usb-0000:00:1d.0-1.4/input0
[ 10.918019] input: American Megatrends Inc. Virtual Keyboard and Mouse as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.1/0003:046B:FF10.0002/input/input3
[ 10.918245] hid-generic 0003:046B:FF10.0002: input,hidraw1: USB HID v1.10
Mouse [American Megatrends Inc. Virtual Keyboard and Mouse] on
usb-0000:00:1d.0-1.4/input1
[ 10.918692] hid-generic 0003:051D:0003.0003: hiddev0,hidraw2: USB HID v1.00
Device [American Power Conversion Smart-UPS 2200 FW:UPS 06.3 / MCU 11.0] on
usb-0000:00:1d.0-1.8/input0
[ 10.925117] random: fast init done
[ 10.929067] mpt2sas_cm0: [0x00]:03100200
[ 10.939600] ata2: SATA link down (SStatus 0 SControl 300)
[ 10.951294] mpt2sas_cm0: [0x04]:00002300
[ 10.984639] sda: sda1 sda2 sda3
[ 10.985180] mpt2sas_cm0: [0x08]:00000000
[ 11.005873] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 11.006343] mpt2sas_cm0: [0x0c]:00000000
[ 11.285853] mpt2sas_cm0: [0x10]:00000000
[ 11.298311] mpt2sas_cm0: [0x14]:00010080
[ 11.310617] mpt2sas_cm0: [0x18]:22137ec7
[ 11.322831] mpt2sas_cm0: [0x1c]:0001285c
[ 11.334964] mpt2sas_cm0: [0x20]:14000600
[ 11.347072] mpt2sas_cm0: [0x24]:00000020
[ 11.359060] mpt2sas_cm0: [0x28]:04000020
[ 11.370880] mpt2sas_cm0: [0x2c]:00810080
[ 11.382482] mpt2sas_cm0: [0x30]:007f0003
[ 11.393927] mpt2sas_cm0: [0x34]:0020ffe0
[ 11.405226] mpt2sas_cm0: [0x38]:008004b0
[ 11.416400] mpt2sas_cm0: [0x3c]:00000011
[ 11.427427] mpt2sas_cm0: [0x40]:00000000
[ 11.438335] mpt2sas_cm0: CurrentHostPageSize is 0: Setting default host page
size to 4k
[ 11.453888] mpt2sas_cm0: CurrentHostPageSize(0)
[ 11.465416] mpt2sas_cm0: hba queue depth(32455), max chains per io(128)
[ 11.479358] mpt2sas_cm0: request frame size(128), reply frame size(128)
[ 11.493291] mpt2sas_cm0: _base_make_ioc_ready
[ 11.507135] mpt2sas_cm0: _base_get_port_facts
[ 11.519349] igb 0000:07:00.0: added PHC on eth0
[ 11.530468] igb 0000:07:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 11.544129] igb 0000:07:00.0: eth0: (PCIe:5.0Gb/s:Width x4)
00:1e:67:97:4d:e9
[ 11.558034] igb 0000:07:00.0: eth0: PBA No: 100000-000
[ 11.569355] igb 0000:07:00.0: Using MSI-X interrupts. 8 rx queue(s), 8 tx
queue(s)
[ 11.616691] offset:data
[ 11.624765] mpt2sas_cm0: [0x00]:05070000
[ 11.634321] mpt2sas_cm0: [0x04]:00000000
[ 11.643579] mpt2sas_cm0: [0x08]:00000000
[ 11.652537] mpt2sas_cm0: [0x0c]:00000000
[ 11.661248] mpt2sas_cm0: [0x10]:00000000
[ 11.669892] mpt2sas_cm0: [0x14]:00003000
[ 11.678382] mpt2sas_cm0: [0x18]:00000100
[ 11.686741] mpt2sas_cm0: _base_allocate_memory_pools
[ 11.696171] mpt2sas_cm0: scatter gather: sge_in_main_msg(1),
sge_per_chain(9), sge_per_io(128), chains_per_io(15)
[ 11.715890] ------------[ cut here ]------------
[ 11.725227] WARNING: CPU: 0 PID: 5 at mm/page_alloc.c:4831
__alloc_pages_nodemask+0x1ce/0x310
[ 11.739330] Modules linked in: fjes(-) hid_generic usbhid hid
crct10dif_pclmul igb(+) crc32_pclmul ghash_clmulni_intel dca aesni_intel ptp
ahci crypto_simd mpt3sas(+) pps_core xhci_pci cryptd mlx4_core(+) raid_class
i2c_algo_bit libahci xhci_pci_renesas glue_helper scsi_transport_sas wmi uas
usb_storage deflate
[ 11.791023] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.8.12 #1
[ 11.803622] Hardware name: ZTSYSTEM CYPRESS11 /S2600CP , BIOS
SE5C600.86B.02.06.0006.032420170950 03/24/2017
[ 11.827610] Workqueue: events work_for_cpu_fn
[ 11.838884] RIP: 0010:__alloc_pages_nodemask+0x1ce/0x310
[ 11.851367] Code: ff ff ff 65 48 8b 04 25 c0 7b 01 00 48 05 78 08 00 00 41
bd 01 00 00 00 48 89 44 24 08 e9 05 ff ff ff 81 e7 00 20 00 00 75 02 <0f> 0b 45
31 ed eb 95 44 8b 64 24 18 65 8b 05 1f a6 7a 4b 89 c0 48
[ 11.893686] RSP: 0018:ffffc18e000bbc98 EFLAGS: 00010246
[ 11.906822] RAX: 0000000000000000 RBX: 0000000000000cc0 RCX:
0000000000000000
[ 11.922228] RDX: 0000000000000000 RSI: 000000000000000b RDI:
0000000000000000
[ 11.937510] RBP: 000000000075d000 R08: 000000000075d000 R09:
ffffffffffffffff
[ 11.952755] R10: 0000000000000000 R11: ffff9e6a16c22350 R12:
ffffffffffffffff
[ 11.967942] R13: 0000000000000000 R14: ffff9e5215c34f58 R15:
ffff9e52163590b0
[ 11.983165] FS: 0000000000000000(0000) GS:ffff9e521ea00000(0000)
knlGS:0000000000000000
[ 11.999566] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 12.013320] CR2: 000055c7853e9ef0 CR3: 00000003d620a003 CR4:
00000000000606f0
[ 12.028719] Call Trace:
[ 12.038777] dma_direct_alloc_pages+0x171/0x2a0
[ 12.051185] dma_pool_alloc+0xd0/0x1c0
[ 12.062585] base_alloc_rdpq_dma_pool+0x118/0x1d0 [mpt3sas]
[ 12.076131] _base_allocate_memory_pools+0x2d6/0x1240 [mpt3sas]
[ 12.090232] mpt3sas_base_attach+0x4a4/0x930 [mpt3sas]
[ 12.103599] _scsih_probe+0x4e3/0x920 [mpt3sas]
[ 12.116383] local_pci_probe+0x42/0x90
[ 12.128401] work_for_cpu_fn+0x16/0x20
[ 12.140466] process_one_work+0x208/0x400
[ 12.152910] worker_thread+0x221/0x3e0
[ 12.165053] ? process_one_work+0x400/0x400
[ 12.177573] kthread+0x117/0x130
[ 12.188759] ? kthread_park+0x90/0x90
[ 12.200400] ret_from_fork+0x22/0x30
[ 12.211748] ---[ end trace 1d2f9a5394100a7e ]---
[ 12.224134] mpt2sas_cm0: mpt3sas_base_free_resources
[ 12.237582] mpt2sas_cm0: _base_make_ioc_ready
[ 12.249253] mpt2sas_cm0: mpt3sas_base_unmap_resources
[ 12.264417] igb 0000:07:00.1: added PHC on eth1
[ 12.276024] igb 0000:07:00.1: Intel(R) Gigabit Ethernet Network Connection
[ 12.290184] igb 0000:07:00.1: eth1: (PCIe:5.0Gb/s:Width x4)
00:1e:67:97:4d:ea
[ 12.304604] igb 0000:07:00.1: eth1: PBA No: 100000-000
[ 12.316624] igb 0000:07:00.1: Using MSI-X interrupts. 8 rx queue(s), 8 tx
queue(s)
[ 12.331505] mpt2sas_cm0: _base_release_memory_pools
[ 12.343209] mpt2sas_cm0: failure at
drivers/scsi/mpt3sas/mpt3sas_scsih.c:10791/_scsih_probe()!
--
You are receiving this mail because:
You are on the CC list for the bug.
next parent reply other threads:[~2020-09-29 19:59 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <bug-209177-11613@https.bugzilla.kernel.org/>
2020-09-29 19:59 ` bugzilla-daemon [this message]
2020-09-29 20:00 ` [Bug 209177] mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10791/_scsih_probe()! bugzilla-daemon
2020-09-30 19:03 ` bugzilla-daemon
2020-09-30 19:04 ` bugzilla-daemon
2021-04-11 7:43 ` bugzilla-daemon
2022-01-03 0:42 ` bugzilla-daemon
2023-10-09 8:29 ` bugzilla-daemon
2024-06-22 11:32 ` bugzilla-daemon
2024-06-22 11:49 ` bugzilla-daemon
2024-07-02 8:09 ` bugzilla-daemon
2024-07-02 8:55 ` bugzilla-daemon
2024-07-02 9:45 ` bugzilla-daemon
2024-09-12 10:54 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bug-209177-11613-OSE9e4xQRI@https.bugzilla.kernel.org/ \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.